I have two of the ix-12 series 12" subs on the rp1000.1D they handle it just fine there subs are so conservatively rated and I bought there amp wiring kit witch was plenty of wire and 4 skar audio 6x8's and to of there super tweeters mids and highs powered with a power acoustic 2,500 watt amp tuned to around 400 watts and the subs on the skar rp1000.1D man it freaking hits hard everyone I have gave a demo thanks I spent thousands on it all together it was $657.96
I've put mine into protect a few time low voltage 3 time speaker wire touching twice comes out of protect no probs but Hart still skips a beat every time
I actually have 2 evls 12's as spares to. Plus I got a sk2500 and a rp2000 as spares. Ive always ran skar audio in my car. currently got 2 vxf 12's on a rp4500 and man do they sub. I have another car with 2 rp2000's on 2 more vxf 12's and again I'm impressed.
I love the skar product I have a skar RP 4500w rms amp on 4 skar zvx 12s in a 4th order wall build in a 94 Toyota Camry and all skar mids and tweeters and I am impressed with skar
Not hard to install. Connect the rca wires together and get ready to BOOM. I have 1 12" @ 1 ohm EVL on a super bass box and being powered by the SKAR AUDIO SKv2 1500.1D @ 1 ohm. The whole car is SKAR AUDIO. Tweeters, 6x9's, 6.5's soundbox 0 gauge wires. Later on a 12" ZVX on a RP2000.1d is being is next. The box is being built for that project.
Ok I hooked this amp up yesterday to my SA 12 V2 sub and tuned it using the SMD DD1 and set the crossover using the SMD CC1 and set the Subsonic to 24 HZ because my box is tuned to 32 HZ. Don’t get me wrong the amp puts out its rated power and some but I did notice a little lack in the sound quality. I had my other amp hooked up first and it sounded very clean with rated power for my subwoofer on the dot. Sundown subs are underrated you can get way more performance out of them that is why I got this amp. I did notice it made my sub hit very hard because my rear view mirror immediately went down to the down position when the bass hit hard and parts of my car was vibrating that were not vibrating before. I hooked my other amp up today and noticed the night and day difference on the sound quality. And the one thing I did notice with my other amp was when I was playing it with just the sub without my mids and highs the bass was very clean with no unwanted frequencies. With the RP 2000.1 doing the same thing I can hear a slight frequency of the instrumentals or higher frequency slipping through. And I did not hear that on my other amp and I used the SMD DD1 and the CC1 to set everything and the subsonic set correctly because I don’t want to damage my sub. I think the main flaw in this amp is the crossovers that is affecting the sound quality but it hits pretty dam hard I must say just make sure you set your subsonic correctly; you don’t want to damage your sub. I am going to test it out for about a week and hook up a DSP and see if I can tailor the sound a little bit better. My other amp puts out half the power but cost about $70 more. So I guess you get what you pay for. For the power it puts out it is well worth the money, I am going to see if I can improve the sound with a DSP. If I can get the sound a little better I will keep it.
I got a set of dual 12 evls for free. Super excited. I really like loud bass. Hope my electrical should be fine with the rp2000.1d. It's not an insane amp and purposely got one with less wattage so I don't need all that extra stuff. All 0 gauge ofc wiring and the big 3 to help my alternator. Can't wait for the install day.
2nd battery maybe needed depending on power requirements of your 4 channel amp. Measure voltage at the amplifiers inputs with volume set to loudest you will use and check for voltage drop. Too much voltage drop can kill your amp (some amps are more sensitive to voltage drop than others)
*Take the time to MOUNT everything if you got a nice set up* I made wooden molds of my base in the trunk. (the floor) Then I made some thick wood that is also light, but strong. All of My things including amp, and speakers Have frames built around them holding them to the board. They are so strong and reinforced with epoxy. Basically, if someone manages to get into my trunk, they actually won't be able to take anything. How to you beat a theif? Simply make it too hard to take. And for the car? go to your dealership, have them install a remove cut off switch. As soon as the car starts, press the button and shut it off :)
Put some rubber spacers between where your amp is mounted and your amp. Problem solved. Or if you are that worried about it wire it to 2 ohms instead of 1. I've not had any problems with mine tho.
@@TheReeferCuz wow that's crazy man. Only problem I've had with skar is I ordered a evl 15 and the dustcap was messed up, it's like the logo is peeling off the cap.
JL Audio to scar not only has the price better but the scar hit harder sound better and put up better Dino numbers or however they measure it underrated they can handle more than they are quoted to evl series absolutely blew my w6s away and performance range price power never buy another high-end set of speakers again when I can get these I promise anybody reading this comment that you cannot go wrong these things freaking lb saying that I would worry about is an alternator for your vehicle LOL because the big boy monobloc ants will eat them
Thanks for this video man! Just bought this same Amp, waiting on delivery. Will be Pushing 2 Sundown SA V.2 12's off of a 320a Alternator. Should boom?!
@@Kpaceguy awesome I cant wait to get it installed, I just have to swap out my stinger 4 gauge power and ground out for some 1/o ofc and I will be ready to go. I'm also going to be putting in a dsp.
You will like the skar audio products I have a SKAR RP 4500w rms amp on 4 SKAR ZVX 12s in a walled 4th order box in a 94 Toyota Camry and I love how hard they hit I am doing a 152.38db
I have the same amp and it gets warm but not hot. Running it @1 ohm and I run full tilt all the time no problems. Just dont mount to sub enclosure or skar wont warranty it.
Wait a minute a diagram that I saw it said that if you were wiring two dual four ohm voice coils to the amp then you wanted to Hook the speaker wire to the middle terminals. Maybe I have my system set up wrong can anyone confirm how you're supposed to wire up the subs to the amp?. I wired up two EVL 12 dual voice coil 4 ohm in the box for one ohm operation. I got a plus and minus speaker wire coming out of the box going into the amp. Which terminals do I use? Hopefully I haven't caused any damage to the speakers
If you're wiring 2 dual 4 ohm subs to 1 ohm amp you Need to go positive to positive and negative and negative on both subs then tether a positive and one negative going to one positive and one negative of the other sub.
@@Kpaceguy no what I'm saying is how do you hook the subs up to the amp I have everything wired up in the box down to one ohm and it comes out of one set of terminals on the side of the box and a positive and negative speaker wire goes from that and then into the amp. I read somewhere that you're supposed to use the middle terminal on the amp the plus and minus in the middle of the amplifier. Now am I supposed to be going by What you showed in the video?. If so, am I running my subs at the wrong power the wrong ohms. Or does it not matter on the amp end? Should I rehook up my box to the amp based on how you did it will it make a difference Or is using the middle terminals fine My box only has one set of terminals coming out of one side of it
@jaygee6983 it changes from amp to amp what terminals to use. So you'll need to download your manual if you don't have it. It 100% matters on the amp end what ohms you're running. It doesn't matter how you have things wired going out of the box it matters how you have the subs hooked up together which is what I just described.
@@Kpaceguy I have the RP 2000 skar I just purchased and it looks like what you show in the video. You use different terminals than I used. I wired the subs parallel for a one ohm load. I saw somewhere that they hooked up the plus and the minus in the middle of the amp. Is that right or do I got to use the same terminals you used. I guess I can read the book that came with the amp again but it didn't really show. It shows the wiring going to both terminals. It shows all four speaker terminals being used on the amp It doesn't really explain how you would hook up for parallel mode. The way I wired my box one terminal has leads coming out of it that would go to the amp so I only have two speaker wires, one positive and one negative so I'm kind of just trying to figure out where I hook those up on the amp if maybe I have it wrong
@@downhilldaddy9346 The one that was fine was sold. The one I Repaired is the one I have now that I'm selling. I put a video up of it. Sounds and works incredibly
single 2.500 watt along with 1.250 watt rms baby double makes 5k 2.500 rms sounds reasonable lol 30 32 hz he can shake house windows with that low hits
@@Kpaceguy if he is only using one 2000 watt amp he is only getting 2000 watts I know the amp does do over rated watts but only around 2700 watts so that's all he's getting.
@@Kpaceguy it.hold.up.two.good deal. Am sure find some useful for.them sell them locally or. Giveaway or sell them to.me lol timnowlin1@gmail.com.. I'll buy them
, Audio customer support is definitely one of the best they look out for their customers
I would send it back to Skar audio. It was VERY NICE THEY DID THAT FOR YOU!! I my self am building a Skar system!! ( make sure you break the subs in).
Breaking in subs is a myth
Haha @ myth.. go buy some $300 subs and push them as hard and as long as you can right out of the box. Lmk how that works out.
I have two of the ix-12 series 12" subs on the rp1000.1D they handle it just fine there subs are so conservatively rated and I bought there amp wiring kit witch was plenty of wire and 4 skar audio 6x8's and to of there super tweeters mids and highs powered with a power acoustic 2,500 watt amp tuned to around 400 watts and the subs on the skar rp1000.1D man it freaking hits hard everyone I have gave a demo thanks I spent thousands on it all together it was $657.96
Bro I'm going to post a video of my setup on my channel here in just a bit if you wanna check it out
skar doesn’t have a rp 1000 only the rp 1200
@@THEBLOODYBALLOON yeah thats what i meant
I love how so many of these amps have a scratch right though the logos. SO many of us drop the knife too far down when boxing lol
I've been waiting since the first one for this video. NOW I have to wait for a third?? You're driving me crazy!! LOL!!
Building suspense! Lol
Bro just subbed i have been saving up for months for my evl 12s
Welcome to the crew
get 1x12 with amp and wiring kit trust me 1x12 with box all that is enough power👍🏻
I've put mine into protect a few time low voltage 3 time speaker wire touching twice comes out of protect no probs but Hart still skips a beat every time
Very scary
I would love to get the broke ones to rebuild them .
Name your price! I just sold the working sub! You're welcome to buy the box and/or broken sub
@@Kpaceguy I build enclosures, but also build subs and am liking that evl motor. Problem is I am too broke 😪. Been a very hard year .
@@boominc0420 I understand! That's a hobby I wish I could do!
@@Kpaceguy just takes patience and time bud .
I'll buy the broke sub text me 7724107027
I actually have 2 evls 12's as spares to. Plus I got a sk2500 and a rp2000 as spares. Ive always ran skar audio in my car. currently got 2 vxf 12's on a rp4500 and man do they sub. I have another car with 2 rp2000's on 2 more vxf 12's and again I'm impressed.
I'm glad to hear that because tomorrow will be my first time with anything skar audio
famshotcaller do you hear a noticeable difference between the rp and the sk series amplifiers?
Honestly no I don't
@@Kpaceguy I promise skar audio will impress you. Follow my Instagram @famshotcaller. U will see
I love the skar product I have a skar RP 4500w rms amp on 4 skar zvx 12s in a 4th order wall build in a 94 Toyota Camry and all skar mids and tweeters and I am impressed with skar
I suggest a PAC- LC1 bass knob. It runs from the back of your radio. Simple and more convenient. Thank you.
I'm not sure I've ever heard of that
Look on Amazon. They have it really cheap. It replaces the long wire from the amp to the radio.
@@chingas24 I appreciate it
Not hard to install. Connect the rca wires together and get ready to BOOM. I have 1 12" @ 1 ohm EVL on a super bass box and being powered by the SKAR AUDIO SKv2 1500.1D @ 1 ohm. The whole car is SKAR AUDIO. Tweeters, 6x9's, 6.5's soundbox 0 gauge wires.
Later on a 12" ZVX on a RP2000.1d is being is next. The box is being built for that project.
To get it out from protect mode you must disconnect all wires power ground rca’s and remotes wait a few minutes then reconnect.
Get a custom enclosure made for the three 12s and get a skar rp 3500 or 4500
Ok I hooked this amp up yesterday to my SA 12 V2 sub and tuned it using the SMD DD1 and set the crossover using the SMD CC1 and set the Subsonic to 24 HZ because my box is tuned to 32 HZ. Don’t get me wrong the amp puts out its rated power and some but I did notice a little lack in the sound quality. I had my other amp hooked up first and it sounded very clean with rated power for my subwoofer on the dot. Sundown subs are underrated you can get way more performance out of them that is why I got this amp. I did notice it made my sub hit very hard because my rear view mirror immediately went down to the down position when the bass hit hard and parts of my car was vibrating that were not vibrating before. I hooked my other amp up today and noticed the night and day difference on the sound quality. And the one thing I did notice with my other amp was when I was playing it with just the sub without my mids and highs the bass was very clean with no unwanted frequencies. With the RP 2000.1 doing the same thing I can hear a slight frequency of the instrumentals or higher frequency slipping through. And I did not hear that on my other amp and I used the SMD DD1 and the CC1 to set everything and the subsonic set correctly because I don’t want to damage my sub. I think the main flaw in this amp is the crossovers that is affecting the sound quality but it hits pretty dam hard I must say just make sure you set your subsonic correctly; you don’t want to damage your sub. I am going to test it out for about a week and hook up a DSP and see if I can tailor the sound a little bit better. My other amp puts out half the power but cost about $70 more. So I guess you get what you pay for. For the power it puts out it is well worth the money, I am going to see if I can improve the sound with a DSP. If I can get the sound a little better I will keep it.
So buy two to make it better in quality
get the skv2 series wayy better sound quality
I got a set of dual 12 evls for free. Super excited. I really like loud bass. Hope my electrical should be fine with the rp2000.1d. It's not an insane amp and purposely got one with less wattage so I don't need all that extra stuff. All 0 gauge ofc wiring and the big 3 to help my alternator. Can't wait for the install day.
Yup you should be fine but wouldn't hurt to get a 2nd battery
2nd battery maybe needed depending on power requirements of your 4 channel amp. Measure voltage at the amplifiers inputs with volume set to loudest you will use and check for voltage drop. Too much voltage drop can kill your amp (some amps are more sensitive to voltage drop than others)
Have a give-a-way contest!
*Take the time to MOUNT everything if you got a nice set up*
I made wooden molds of my base in the trunk. (the floor) Then I made some thick wood that is also light, but strong.
All of My things including amp, and speakers Have frames built around them holding them to the board. They are so strong and reinforced with epoxy.
Basically, if someone manages to get into my trunk, they actually won't be able to take anything. How to you beat a theif? Simply make it too hard to take.
And for the car? go to your dealership, have them install a remove cut off switch. As soon as the car starts, press the button and shut it off :)
Wish i was lucky to get even one of those speakers
Upgrading very soon. One could be yours. Subscribe if you havent already because I'll be getting rid of these very very soon
Give this guy a free sub.... Good karma!
shii you can send it to me 😂😂
How you been k pace my son was born an hour ago I'm so happy and keep the videos coming
Congrats!
@@Kpaceguy thank you 7 pounds and 12 ounces I see your doing big house systems they real nice
@@betotheboss8469 I appreciate it
Do you have any overheating problems with the rp 2000? Beacuse i do 🙁
Nope haven't ran into any problems so far
I heard they overheat if u mount them on the box or any flat surface because of vents being on the bottom.
Put some rubber spacers between where your amp is mounted and your amp. Problem solved. Or if you are that worried about it wire it to 2 ohms instead of 1. I've not had any problems with mine tho.
I sold the amp theres reviews that it does not like 2ohms and I did go with 2 ohms and it was worse
@@TheReeferCuz wow that's crazy man. Only problem I've had with skar is I ordered a evl 15 and the dustcap was messed up, it's like the logo is peeling off the cap.
Meanwhile I'm getting ready to return my skar evl 12s cus they're too heavy for my 2012 honda accord. Got the evl 15 in my backseat.
Plus. At full excursion, that plinth may be too close. Hope it down. Lol 👍🏻👍🏻👍🏻👍🏻I meant chop it down 😂😂😂
Skar makes good stuff for the money. But for your audio tastes man you deserve better....zapco cough cough
Never heard of them lol
@@Kpaceguy 😳 zapco is the stuff Legends are made of
@@donellis5005 zapco so overated
JL Audio to scar not only has the price better but the scar hit harder sound better and put up better Dino numbers or however they measure it underrated they can handle more than they are quoted to evl series absolutely blew my w6s away and performance range price power never buy another high-end set of speakers again when I can get these I promise anybody reading this comment that you cannot go wrong these things freaking lb saying that I would worry about is an alternator for your vehicle LOL because the big boy monobloc ants will eat them
Thanks for this video man! Just bought this same Amp, waiting on delivery. Will be Pushing 2 Sundown SA V.2 12's off of a 320a Alternator. Should boom?!
I hope you didn't leave them speaker up against that blue block you realize the speakers move when they hit
There's probably 3in of clearance between surround and the wood
i bought this but have not hooked it up yet, have you had any problems with it.
None whatsoever
@@Kpaceguy awesome I cant wait to get it installed, I just have to swap out my stinger 4 gauge power and ground out for some 1/o ofc and I will be ready to go. I'm also going to be putting in a dsp.
Nicely done!
Are you going to use a extra battery or h.o. Alternator?
I have 2 battery's currently
How do you hook up a extra battery im new to all this I have a skar rp3500 Nd 2 evl 15s
The way to use the bass boost is to turn it up all the way when you set your gains so that switching it on wont send a clip signal
I’ll buy
Long gone. When I post these thing they go almost same day
Send them my way
Speaker terminals don't matter it's a mono block
I know the gain is not a volume knob if my pioneer head unit is 2v where is the 2v gain set to is it ailtte over half? 3/4?? Please help
You need a distortion detector of some sort. Take it to your nearest audio shop
What is the best way to wire two skar EVL twelve's 4ohm on to a scar 2000. 1D watt amp
You will like the skar audio products I have a SKAR RP 4500w rms amp on 4 SKAR ZVX 12s in a walled 4th order box in a 94 Toyota Camry and I love how hard they hit I am doing a 152.38db
Make a video bro
@@LIFEWITHDANTE my buddy is Starting a you tube channel to follow I will have some video's of my system and I just upgraded to a Taramps 12k 1ohm amp
@@LIFEWITHDANTE we will post some video's of it on there for everyone to see it oh yah and now it's a 6th order also
@@bassheadfanatic950 lmk when its up 💪🏾😎
@@LIFEWITHDANTE will do I will let you know when we post
any problems with overheating with the wood amp rack ? im waiting to install mine had it all over a year
Nope not at all but I don't run it at Hugh volumes too often
@@Kpaceguy appreciate the reply bro thank you all i have left is just plug in all my wires and build amp rack just didnt want to send it in to protect
I have the same amp and it gets warm but not hot. Running it @1 ohm and I run full tilt all the time no problems. Just dont mount to sub enclosure or skar wont warranty it.
Could a 4 gauge kit work on that amp??
Not recommended
no, that amplfier isn’t a fan of bad voltage either. i’ve got one and i’ve noticed it doesn’t like below 13 for me. you’d be best of using 1/0 ofc
Can i have the broken evl ?
Can the EVL 10inch single sub handle this 2000w amp? Just asking bc I just order the 10inch n don't know if I should pair with this amp.
Its probably perfect for it just be mindful of how long you play it at full volume
You knocked on the amp and said " nice and sturdy solid metal". When have you ever seen an amplifier made out of anything but metal?
I've seen tons of hard plastics
What ohm are the evls? 2 or 4? Im new to this.
They come in dual 2 or 4 ohms depending on how many you want to run and how stable your amp is
You can wire two D4’s down to 1 ohm or keep at 4 ohm.
2 Ohm to 1 ohm in box comes with it im guessing so u just wire it unless custom box well start tunning up lol
You selling the enclosure?
Metal it's metal
How many batteries do you have
1 extra in the trunk
Buy a Skar single loaded enclosure and put the single good EVL in the house foe at home listening!!
Did you use the 3000 watt ofc wiring kit?
Not a kit but it is ofc 0 gauge
@@Kpaceguy what’s the wattage of your wire?
@@derrickwalters78 2000+ watts
I’ll buy the working 12 from you dude for a lower price. Let me know
How does $110 sound??
Let’s do it. Want my Venmo?
@@Evadingmoto PayPal would work much better for me if you could. Send me an email @ Xboxtube@live.com
Okay sounds good.
You buy it?
Man that basket really shouldn't have broken like that.
Wait a minute a diagram that I saw it said that if you were wiring two dual four ohm voice coils to the amp then you wanted to Hook the speaker wire to the middle terminals. Maybe I have my system set up wrong can anyone confirm how you're supposed to wire up the subs to the amp?.
I wired up two EVL 12 dual voice coil 4 ohm in the box for one ohm operation. I got a plus and minus speaker wire coming out of the box going into the amp. Which terminals do I use? Hopefully I haven't caused any damage to the speakers
If you're wiring 2 dual 4 ohm subs to 1 ohm amp you Need to go positive to positive and negative and negative on both subs then tether a positive and one negative going to one positive and one negative of the other sub.
@@Kpaceguy no what I'm saying is how do you hook the subs up to the amp I have everything wired up in the box down to one ohm and it comes out of one set of terminals on the side of the box and a positive and negative speaker wire goes from that and then into the amp. I read somewhere that you're supposed to use the middle terminal on the amp the plus and minus in the middle of the amplifier.
Now am I supposed to be going by What you showed in the video?.
If so, am I running my subs at the wrong power the wrong ohms. Or does it not matter on the amp end?
Should I rehook up my box to the amp based on how you did it will it make a difference Or is using the middle terminals fine
My box only has one set of terminals coming out of one side of it
@jaygee6983 it changes from amp to amp what terminals to use. So you'll need to download your manual if you don't have it. It 100% matters on the amp end what ohms you're running. It doesn't matter how you have things wired going out of the box it matters how you have the subs hooked up together which is what I just described.
@@Kpaceguy I have the RP 2000 skar I just purchased and it looks like what you show in the video. You use different terminals than I used.
I wired the subs parallel for a one ohm load. I saw somewhere that they hooked up the plus and the minus in the middle of the amp. Is that right or do I got to use the same terminals you used.
I guess I can read the book that came with the amp again but it didn't really show. It shows the wiring going to both terminals. It shows all four speaker terminals being used on the amp It doesn't really explain how you would hook up for parallel mode. The way I wired my box one terminal has leads coming out of it that would go to the amp so I only have two speaker wires, one positive and one negative so I'm kind of just trying to figure out where I hook those up on the amp if maybe I have it wrong
@@jaygee6983 use the same I used.
🀄️
I just bought the package does the rp 2000 SKAR amp do a good job at 2 ohms with the skar Evls cuz I wanna do 2ohms
No it's intended to be at 1 ohm and there's not really a reason why you wouldn't
So it’s the rp 2000 is good at 1ohm for the evls
@@shirazalli5566 yes
Did you need an upgraded alt, or capacitor or anything to help run this stock?
No but to get the best out of your amps I'd upgrade alt and battery
@@Kpaceguy didnt watch the video yet but what kinda car is it? waiting on my evl 12s and the skar 2000.d
@@BigHemiNJ 2016 accord
Are the Speakers any good?
Can I get them !! Please I want some speakers I’m willing to pay !
They've been gone a long time
Hey kpaceguy can u send me the wire diagram on the subs got a pair and wanting to know how to hook the bad boys up
Sure how do you want me to send it
Here just tell me we’re wire go we’re to we’re thanks
Lemme have the extra box and evl’s
I have 1 evl for sell
Kpaceguy how much?
@@downhilldaddy9346 Getting rid of it for 110
Kpaceguy so it isn’t the damaged one right?
@@downhilldaddy9346 The one that was fine was sold. The one I Repaired is the one I have now that I'm selling. I put a video up of it. Sounds and works incredibly
Hi bro what amp would you recommend for 2 skar VD-12 4 ohm?
Skar rp1500.1
So if I have just one Evl 12 and this amp you think my battery will be able to handle it without the big 3? 97 honda civic
Yes but I'd still do the big 3.
@@Kpaceguy alright. What about you think it'd fit under my seat? 😂
@@zslinkyzx9831 definitely not
Hey would this be enough power for both of the subs, I have 2 and I don’t know if I should go with this or the mono block 2500
What subs. If you're talking about vxf 2500 isn't enough. I'm finding that out now
Kpaceguy I have the evl 12s I was wondering if the SKV2-2500.1D would power it alright
The would be good
Help a mexican brother out with 1 evl 12 :D
Still for sale if you want it
dude is 200$ lol
Ps. Bin the old box.
Used jb weld and fix it
Why did you put 5000w in the title? It's a 2000w amp
Speakers max power combined
Oh, gonna need like two of these amps to even get close that 5k
@@rickytrevino8281 I have a whole new system
@@Kpaceguy What is it
@@rickytrevino8281 its on the channel
I have 2 skar evl 10s what amp do you recommend
2000.1D or 2500.1D
@@Kpaceguy hey I just researched, do you think a rockville db14 would work fine, my subs are 2 Ohm stable.
@@lilmudbuddy7633 yes but that 2000w rms probably isn't at 2ohms.
What about a Taramp's MD 3000.1
@@lilmudbuddy7633 that would be fine
Um, thats 2000 watts my dude
Dual evl max power combined is a total of 5000 watts
single 2.500 watt along with 1.250 watt rms baby double makes 5k 2.500 rms sounds reasonable lol 30 32 hz he can shake house windows with that low hits
@@Kpaceguy if he is only using one 2000 watt amp he is only getting 2000 watts I know the amp does do over rated watts but only around 2700 watts so that's all he's getting.
Can I have the extra evl lol
This has been long given away
@@Kpaceguy yea I figured😭😭😭
Or.do giveaway I'll pay for shipping lol
I broke mine the same way
Looks like sabotage to me!
I sure hope not
Kpaceguy jeeze mate, it looks well mashed!!! 👍🏻 good luck you have a replacement 👍🏻👍🏻👍🏻
Kpaceguy I think it’s only because of your channel they replaced that to be honest. Otherwise they’d blame you. I’ve had that shit. 👍🏻
Skar has great customer service. The channel has nothing to do with it. They really do replace any damages. All they ask for is pictures to prove it.
I'll buy it all just jb welid it
Yep I used jb weld. Worked like a charm
@@Kpaceguy it.hold.up.two.good deal. Am sure find some useful for.them sell them locally or. Giveaway or sell them to.me lol timnowlin1@gmail.com.. I'll buy them
Just donate them to me. I have a box with no subs for my 2000 Camaro
Dam..your shit always breaking 🤔