Thank you so much, my launcher got stuck while launching fafnir and i was afraid of opening it without knowing what to do because i already broke a crap ton of string launchers not knowing how to fix them
@@stephensiegel66 thank you soo much I really appreciate it 🙏🏻 bc I think my spring inside needs to be fixed cause it doesn’t rewind at all when I twist the switch with my screw driver
If you’re talking about the smaller gears you’re going to need to put the pull side of the string in between the two gears and gently rotate one of them the string will push through and get free. To avoid that from happening again use a thing piece of cardboard from a new bey box cut it out so it can cover the gears
The ribbon or the gears are locked out, make sure proper spin orientation is done before you retract the string LR Launchers should be in right spin to reset the launcher after repair. Also make sure the ribbon is orientated the right way. It took me a few tries to get it right.
Hello, I don't know if you're going to see this comment, but the tutorial to repair it, I don't know if something's wrong, oh, follow the tutorial, I did something wrong, but you could do another updated tutorial.😊
The best way I have found is full strength liquid gorilla glue now that is if the stem is attached to the gear and pin. If the pin/screw is is no longer staying in place, then take a toothpick and dip it into the glue and use the tip of the pick to push glue into the hole and only in the hole the pin goes in. Make sure you don’t get it on the top of the pin or the gear will stick to the stem. After glue is in the hole insert the pin in the gear and then the pin in the hole let the glue cure for at least 48 hours then you should be fine only pull lightly for the first few times to make sure it works, and then ease the launcher into full use.. hopefully the advice works.🙏🏻🙏🏻
So you’re launcher not cranking anymore is either due to the coil spring inside the gear, or the gears themselves in the launcher are stripped. You’ll wanna take apart the launcher and very closely watched this video.
I apologize. I thought I had posted a video on how to repair your string launcher. I will be uploading a video tomorrow the 16th on how to fully disassemble and repair your string launcher. Hopefully it’ll help you out, so stay tuned.
@@ytayeee the piece of plastic holding one of the gears to the body of the launcher, inside it. Take the screws out and separate the two halves of the launcher body and it will be obvious. I fixed one of these launchers for my nephew just yesterday. The glue I use to reattach the broken part is Forch K170.
Thanks for this video, my son’s launcher broke, I tried fixing it but couldn’t get the clockspring back in, now I know how to repair it.
Thank you so much, my launcher got stuck while launching fafnir and i was afraid of opening it without knowing what to do because i already broke a crap ton of string launchers not knowing how to fix them
really smart fix yet so simple
Thank u so much my launcher was not working properly and u just made my day
Legend thanks for this dude! Super helpful. Somehow however, mine now works in reverse haha.
Glad it helped!
Hey found this video and was wondering if you could do a full disassembly video of a betblade burst L launcher struggling with mine
I can most certainly do that
@@stephensiegel66 thank you soo much I really appreciate it 🙏🏻 bc I think my spring inside needs to be fixed cause it doesn’t rewind at all when I twist the switch with my screw driver
THANK YOU SO MUCH
Thanks for the video! I appreciate it!
My string is between the white gears on the top do i have to take them off?
If you’re talking about the smaller gears you’re going to need to put the pull side of the string in between the two gears and gently rotate one of them the string will push through and get free. To avoid that from happening again use a thing piece of cardboard from a new bey box cut it out so it can cover the gears
@@stephensiegel66Also when i let go of the thing when of the place where you put the bey on it doesn’t retract
Thanks you bro!
You're welcome!
can u make a video for when the spring breaks cus mine has broken and idk how to fix it
Yo whenever I try to use it the string doesn't move I opened it but idk how to make the wire come back
The ribbon or the gears are locked out, make sure proper spin orientation is done before you retract the string LR Launchers should be in right spin to reset the launcher after repair. Also make sure the ribbon is orientated the right way. It took me a few tries to get it right.
I buyed a quadstrike launcher and I can't change the L to R it won't turn
pls great beyblade lord share with me ur knowlege the orange cog is super tight n wont reel back
the string doesnt automatically reel back in when i pull it
also havung this prob
It does for me
Just open the lr changer and leave it in the middle for a bit, it'll reel back in
Or leave it alone for a bit, mine just started reeling back
@@migi3139 I fixed it and it didn’t reel back in fully but at least it works
Guys I need help my quad drive string launcher won’t crank anymore… can you guys tell me how to fix it
I have a video for that please go check it out and let me know if it helped.
omg thank you bro
No problem
What if the spring that holds the cord gets too tight?
It’ll either snap the plastic piece inside, drip or break the spring
Wow
everytime i do the thing with my index and it gets tight i stop and it just keeps rebounding
Hoping g this would help but the middle gear actually snapped off
This happened to ours, you can glue them back down and reinforce them. The product we used was Forch K170, but araldite would work too.
How did you unskrew the grip to put the white one
Are you talking about the launcher grip?
No about the tooth thing that you put the beys
There’s a flat gear under the holder and if it no longer stops then flat gear is stripped.
Can you explain it more
Please
Where were you when this happened to me.......
Hello, I don't know if you're going to see this comment, but the tutorial to repair it, I don't know if something's wrong, oh, follow the tutorial, I did something wrong, but you could do another updated tutorial.😊
Thank you I’ll do another one shortly
Where did you get that grip for the quaddrive launcher? I can't find it anywhere.
It was apart of the dual layer series like 6 years ago
I found it in target and walmart
When mine is on right spin it wont work
It is due to the spring being worn out I’ve had the same issue in the past.
One of my gears fell off idk how to fix it
The best way I have found is full strength liquid gorilla glue now that is if the stem is attached to the gear and pin. If the pin/screw is is no longer staying in place, then take a toothpick and dip it into the glue and use the tip of the pick to push glue into the hole and only in the hole the pin goes in. Make sure you don’t get it on the top of the pin or the gear will stick to the stem. After glue is in the hole insert the pin in the gear and then the pin in the hole let the glue cure for at least 48 hours then you should be fine only pull lightly for the first few times to make sure it works, and then ease the launcher into full use.. hopefully the advice works.🙏🏻🙏🏻
it worked but I had to do it like 5-10 times so yea
The coil inside isn't reflecting
Can u guys help me out my launcher won't crank any more
So you’re launcher not cranking anymore is either due to the coil spring inside the gear, or the gears themselves in the launcher are stripped. You’ll wanna take apart the launcher and very closely watched this video.
I apologize. I thought I had posted a video on how to repair your string launcher. I will be uploading a video tomorrow the 16th on how to fully disassemble and repair your string launcher. Hopefully it’ll help you out, so stay tuned.
Mine also broke but like the right spin mode won’t work like when u put a bey on it just falls off
yea mine too
How can I fix it
@@lancestar403 the gear post breaks, you can glue it back down and reinforce it.
@@rsoul7282 what is a gear post bro 💀
@@ytayeee the piece of plastic holding one of the gears to the body of the launcher, inside it. Take the screws out and separate the two halves of the launcher body and it will be obvious. I fixed one of these launchers for my nephew just yesterday. The glue I use to reattach the broken part is Forch K170.
I wish I saw this earlier
Beyblades are cheaply made pieces of garbage after buying a bunch for my kid and using this launcher
So Hasbro doesn’t use the same quality as TT try buying TT beys and if you need help finding them let me know and I’ll help by sending links.👍👍
dose not work
?
?
I buyed a quadstrike launcher and I can't change the L to R it won't turn
Apply the following steps in the video hopefully it’ll help you