Rollers by years listed below: 1999-2004 driver side roller: amzn.to/3RcJefr 1999-2004 passenger side roller: amzn.to/3edvuCA 2005-2010 passenger side roller: amzn.to/3cD5Arq 2005-2010 driver side roller: amzn.to/3wOjkXc 2005-2010 driver & passenger side aftermarket rollers: amzn.to/3q42BeN 2011-2017 passenger side roller: amzn.to/3q5xY8O 2011-2017 driver side roller: amzn.to/3wPf1Le #ad
I looked for the shortest video because I knew there wouldn't be no BS, just straight to the point. Thanks for showing everyone, saved me alot of headache and money.
Thanks for all your awesome videos. Just fixed my passenger sliding door Odyssey 2006 just like you described. Need to mark hinge with black marker to make sure it is aligned properly. Also, it might be easier to bend one side of metal leaf on cable holder so that you can insert back cable easier. Then bend back to secure cable. I found that after I replaced roller, the car would make the alarm door sound whenever I put car in drive, even though the sliding door was closed securely. I found that I needed to reset door by pulling fuse 7 under the driver's side foot well for 10 seconds and then putting it back in. This fuse is labelled BACK UP in owner's manual. This got rid of the door alarm noise and also the sliding door warning yellow light on the dash shut off.
I don't think you needed to pull the fuse. My van made the same beeping noise when I changed the roller. To clear the beep, I opened the door all the way and closed it while the van was on. Beep went away and hasn't made a sound since.
What happens if the hinge is not aligned properly? I marked mine and now the door won't shut or open automatically. If I shut it manually and try to open via power, it beeps three times and doesn't do anything. I've tried readjusting the hinge several times, but not getting any where.
I believe my issue was solved after doing the power sliding door reset feature. The door reset procedure is: 1. turn dash switch off. 2. Open both doors completely manually. 3. Pull passenger f13 for a couple minutes. Resets control units. 4. Replace f13 5. Turn Door switch on dash on. 6. Press and HOLD both dash door close switches until both doors are closed and continue holding for five seconds. Check doors. Try a second time if still a problem. F13 refers to the fuse.
I was working on a 2016 Ody with the same issue and found that even though this is a different van it was similar enough that I could use your video to help me tear down my van. Thanks, this was a HUGE help!
This was a greatly helpful video. My daughter and I replaced both sides in less than 2 hours and they work very well. Not perfectly aligned maybe but they open and close smoothly enough.
Just replaced my driver side roller and man - what an amazing video. GUYS! DO NOT NEGLECT YOUR ROLLERS! Take it from me. My driver side door was acting funny (I could pull it out away from the van a little) and I neglected to fix it. Later my cable got snagged and, not knowing what to do, I resorted to cutting it to free the door and get it working again. Bad, bad, bad move. I will end up paying dearly for that as I now have to replace the cable. The problem was that the roller had lost a wheel so that it was only operating on one wheel and one nub. With this video's help it literally took me 30 mins to get the roller off. And I wasn't going fast at all. Had I changed the roller when it started giving me problems, I would still have a functioning automatic driver door. I'll be checking my passenger door in a couple of days. @MrRangerZr1 - thank you for an incredibly clear, concise, no BS repair video.
Aww man, I just spent $389 for this exact part/fix/service at the Honda Dealer. I had the same exact part in my Amazon cart but just wasn’t sure I could fix it and put Humpty Dumpty back together again. Oh well, I’ll have the know how next time when the other side fails. Thanks !!!
Thanks for the video, my door rollers broke off n the door came off I had to remove the roller and slide the door back on the track, now I just have to replace it like you did in this video.
THANK YOU!!!!!! YOU ARE AWESOME SIR!!!!!!!!!!!!!!! Followed everything just like you did and it went super smooth!!!!!!! Took me maybe 20-30 mins because I was being careful but man way better than paying a shop $200 🥵THANK YOU!!!!!
Mr. Zanger, great video as always. I replaced mine about a year ago. However, whenever I drive, I hear some slight sound, like metal bumping into metal. I suspect I didn’t line up the bolts exactly the way it was before I removed it to change the roller. I’ve tried loosening, jacking up the door a bit more and tightening back 2x, but still hearing the noise. Any suggestions on lining up the door properly to eliminate the noise? I also hear squeaking from the door cable. I spray some lubricant on the cable and it stops.
Mr ranger you gott do a video on removing rear cylinder head and gasket replacement for 2008 honda odyssey great video roller ive been waiting to install that part for over a yr now gona change it out today now thanks my honda TH-cam buddy you the man bro!
Thank you sir! Saved me a bunch of time and gave me a great reference when I was unsure of what to do next! I appreciate your no nonsense and step by step approach! You have helped me with my alternator and now my door rollers, saving me a bunch of money in labor!!! 😃🤗✝️ I can help but wonder is a little grease on the rollers and/or rail would help those bearing last longer?
I followed what I saw in the video. However, when I removed the hinge from the door and reattached it, there is a gap in the door. The door closes, but there is a slight difference. How can I align it properly?
Great video. Like others, after watching a dozen videos, with a dozen personalities of varying competences, I found this one perfectly straight-forward. Thank you very much. However, and no one ever mentioned that the system would need to be reset. Or have others been able to do this repair without needing to reset? I found a method which has mixed results, for me it was not successful, involving the pulling of four different fuses (located across the various fuse boxes), requiring a series of actions, including manually opening the doors with the PSD switch OFF, then Ignition to ON, PSD switch to on, push button til door closes, etc. Didn't work for me. Tried it a couple times in case I flubbed the first on. Any suggestions?
Hello, I just did this repair to replace roller assembly. Great details. My door will close on automatic about 5/6 of the way and the. Stops now. Can close all the way manually without issue. Any recommendations for what to try?
this is exactly what needs to be fixed on our van. I'm not physically able to do the repair myself right now, post-op for 8 weeks. the dealer wouldn't quote the repair. I'm wondering what the time frame was for y'all to do yours?
you did not show how to place back the hing into the exact position where the old one was be ause the door won t lock if is off of the old position even with a hair distance.
They want 650 cad this part now because it's updated and comes with a new electronic circuit board that you have to install on the 4th gens. I'm annoyed
Rollers by years listed below:
1999-2004 driver side roller: amzn.to/3RcJefr
1999-2004 passenger side roller: amzn.to/3edvuCA
2005-2010 passenger side roller: amzn.to/3cD5Arq
2005-2010 driver side roller: amzn.to/3wOjkXc
2005-2010 driver & passenger side aftermarket rollers: amzn.to/3q42BeN
2011-2017 passenger side roller: amzn.to/3q5xY8O
2011-2017 driver side roller: amzn.to/3wPf1Le
#ad
I looked for the shortest video because I knew there wouldn't be no BS, just straight to the point. Thanks for showing everyone, saved me alot of headache and money.
I just fixed my passenger sliding door on my 2010 Honda Odyssey. This video was exactly what I needed. Thank you!
Thanks for all your awesome videos. Just fixed my passenger sliding door Odyssey 2006 just like you described. Need to mark hinge with black marker to make sure it is aligned properly. Also, it might be easier to bend one side of metal leaf on cable holder so that you can insert back cable easier. Then bend back to secure cable. I found that after I replaced roller, the car would make the alarm door sound whenever I put car in drive, even though the sliding door was closed securely. I found that I needed to reset door by pulling fuse 7 under the driver's side foot well for 10 seconds and then putting it back in. This fuse is labelled BACK UP in owner's manual. This got rid of the door alarm noise and also the sliding door warning yellow light on the dash shut off.
I don't think you needed to pull the fuse. My van made the same beeping noise when I changed the roller. To clear the beep, I opened the door all the way and closed it while the van was on. Beep went away and hasn't made a sound since.
What happens if the hinge is not aligned properly? I marked mine and now the door won't shut or open automatically. If I shut it manually and try to open via power, it beeps three times and doesn't do anything.
I've tried readjusting the hinge several times, but not getting any where.
@@mine4751 How about I have the same problem with a 2000, how could you solve it?
I believe my issue was solved after doing the power sliding door reset feature.
The door reset procedure is:
1. turn dash switch off.
2. Open both doors completely manually.
3. Pull passenger f13 for a couple minutes. Resets control units.
4. Replace f13
5. Turn Door switch on dash on.
6. Press and HOLD both dash door close switches until both doors are closed and continue holding for five seconds.
Check doors. Try a second time if still a problem.
F13 refers to the fuse.
I was working on a 2016 Ody with the same issue and found that even though this is a different van it was similar enough that I could use your video to help me tear down my van. Thanks, this was a HUGE help!
Short, sweet, and to the point. Perfect video and all the info you need! Thank you. Changed both door rollers in approx. 1 hour. 10/10
You are honestly the best. Helped me replace my alternator on my 05 Odyssey, now this. Thanks a ton!
This was a greatly helpful video. My daughter and I replaced both sides in less than 2 hours and they work very well. Not perfectly aligned maybe but they open and close smoothly enough.
Just replaced my driver side roller and man - what an amazing video.
GUYS! DO NOT NEGLECT YOUR ROLLERS! Take it from me. My driver side door was acting funny (I could pull it out away from the van a little) and I neglected to fix it. Later my cable got snagged and, not knowing what to do, I resorted to cutting it to free the door and get it working again. Bad, bad, bad move. I will end up paying dearly for that as I now have to replace the cable.
The problem was that the roller had lost a wheel so that it was only operating on one wheel and one nub. With this video's help it literally took me 30 mins to get the roller off. And I wasn't going fast at all. Had I changed the roller when it started giving me problems, I would still have a functioning automatic driver door. I'll be checking my passenger door in a couple of days.
@MrRangerZr1 - thank you for an incredibly clear, concise, no BS repair video.
Ranger Z got some of the best videos around. Hit the like button.
Excellent video... everything I needed w/o all the extra garbage. Thank you!!
Thank You! Simple and straight to the point. Getting ready to swap mine 05 Odyssey 270k
great video watched twice and was able to replace mine on both side trouble free thanks so much!!!!
Aww man, I just spent $389 for this exact part/fix/service at the Honda Dealer. I had the same exact part in my Amazon cart but just wasn’t sure I could fix it and put Humpty Dumpty back together again. Oh well, I’ll have the know how next time when the other side fails. Thanks !!!
Fantastic video like always, quick simple provides all the sizes thank you!
Thanks SO much for this video. It was much easier than I thought and your videos are right on!!
Thanks for the video, my door rollers broke off n the door came off I had to remove the roller and slide the door back on the track, now I just have to replace it like you did in this video.
Helped me fix my rear door , thank you
Thank you much, took nothing but 30 min only because of those dam cables, but overall easy DIY
THANK YOU!!!!!! YOU ARE AWESOME SIR!!!!!!!!!!!!!!! Followed everything just like you did and it went super smooth!!!!!!! Took me maybe 20-30 mins because I was being careful but man way better than paying a shop $200 🥵THANK YOU!!!!!
Thank you!!! This is how to make a helpful video!!
Mr. Zanger, great video as always. I replaced mine about a year ago. However, whenever I drive, I hear some slight sound, like metal bumping into metal. I suspect I didn’t line up the bolts exactly the way it was before I removed it to change the roller. I’ve tried loosening, jacking up the door a bit more and tightening back 2x, but still hearing the noise. Any suggestions on lining up the door properly to eliminate the noise? I also hear squeaking from the door cable. I spray some lubricant on the cable and it stops.
Mr ranger you gott do a video on removing rear cylinder head and gasket replacement for 2008 honda odyssey great video roller ive been waiting to install that part for over a yr now gona change it out today now thanks my honda TH-cam buddy you the man bro!
MrRanger,
Could you make a TH-cam of how to remove the cup stand for Honda Odyssey 2008, please?
Thank you sir! Saved me a bunch of time and gave me a great reference when I was unsure of what to do next! I appreciate your no nonsense and step by step approach! You have helped me with my alternator and now my door rollers, saving me a bunch of money in labor!!! 😃🤗✝️
I can help but wonder is a little grease on the rollers and/or rail would help those bearing last longer?
Some silicone spray doesn't hurt but whatever you use don't use too much as it'll attract dirt. Thanks
I followed what I saw in the video. However, when I removed the hinge from the door and reattached it, there is a gap in the door. The door closes, but there is a slight difference. How can I align it properly?
Well that was easy. Great video once again. Thanks.
To the point and super helpful
Great video. Like others, after watching a dozen videos, with a dozen personalities of varying competences, I found this one perfectly straight-forward. Thank you very much. However, and no one ever mentioned that the system would need to be reset. Or have others been able to do this repair without needing to reset? I found a method which has mixed results, for me it was not successful, involving the pulling of four different fuses (located across the various fuse boxes), requiring a series of actions, including manually opening the doors with the PSD switch OFF, then Ignition to ON, PSD switch to on, push button til door closes, etc. Didn't work for me. Tried it a couple times in case I flubbed the first on. Any suggestions?
You dont need to reset for changing this roller
...mmm ? no need t try to clean and lube up the track and the pivot pin of that hinge ?
You can, mine didn't need it
Hello, I just did this repair to replace roller assembly. Great details. My door will close on automatic about 5/6 of the way and the. Stops now. Can close all the way manually without issue. Any recommendations for what to try?
See if your cable is put properly
this is exactly what needs to be fixed on our van. I'm not physically able to do the repair myself right now, post-op for 8 weeks. the dealer wouldn't quote the repair.
I'm wondering what the time frame was for y'all to do yours?
Not too long honestly, like half hour? Dealer will charge an arm and a leg btw.
@MrRangerZr1 yea, I am thinking to find a local shop that might do it cheaper tan the 3 or 400 the other commenter mentioned.
thank you!
Great video you should have way more then 237 likes ! I’m a sub now
How u gonna replace it if the door wont shut ?
great help sir...thank you
you did not show how to place back the hing into the exact position where the old one was be ause the door won t lock if is off of the old position even with a hair distance.
my '12 odyssey binds up when attempting to close the door using the handle. Is this the fix?
Should be yes
هل ممكن تحويل هذا الباب المنزلق إلى باب يدوي عادي دون ان يكون باب يفتح كهربائيآ؟!!
شكرآ للفيديو 🙏🏻🌷🌷
نعم أخي موجود في السيارة
Thanks Dude
They want 650 cad this part now because it's updated and comes with a new electronic circuit board that you have to install on the 4th gens. I'm annoyed
Old is gold lol
Thanks
I would have used a cheap screw driver instead of the Snapon 😅
Lol