Bro .. I want to thank u!!! I was doing a retro cic swap, and I didn't disconnect the battery. 😢. I touched the monitor wires together during the swap. Then bam all hell breaks loose. Wipers turn on full speed, whinnying noise from my firewall, no electronics in the interior. But my car did start. But I couldn't control my headlights from being on. Man I just wanna thank u really 🎉. Did the swap step by step as u the walla. Thumbs up bro
I found your channel yesterday, and watched a lot of your videos. When I saw video "My BMW is dead..", I said, omG, it's not happening. Than I watched this video where you repaired the car. It's so nice to see how much time you spent upgrading your BMW, and thank you for showing everything like DIY videos. I just want to say, thanks dude, it's pleasure to watch your videos. Best regards from Bosnia and Herzegovina.
The junction box electronics unit detects the following signals and makes them available to other bus users: Power window switch, front passenger door. Power windows switch, right rear door. Power window switch, rear door on driver's side.
What electrical issues were you having before? I’m having wipers being stuck.. parking brake light illuminates when driving even tho brakes are brand new and hand brake down.. passenger seated seats don’t stay on.. they turn on them go off. My tach sometimes doesn’t show gas meter. And my Speedo goes from whatever speed I’m driving at than drops to 0 than returns to my current speed. And my rear passenger windows cut out when rolling up or down got hit the button again to continue
Hey mate . My bmw e90(316d)(2009) is showing yellow engine light which come up time to time. I get it checked with ISTA+ unable to communication most gatway. Unable to communicate to head unit. What could be the problem, is it big problem please guide me. Thanks Anil
@@JDCarsChannelmy lights flicker when I put key in the ignition and brake lights stay on after turning car off fuse box also makes noise when I put key in would u happen to know what it could be? Thanks
Where did you send off your ECU and CAS to get tested see if they are working properly or needed replacing? My car is getting some lights on but none on dash nor starting. Window buttons not working nor radio power. Battery is new
Hi there, my 2011 F10 535i got the similar electrical issues. All in a sudden my windshield wipers will go on and off itself randomly. Then my alarm, locking system, backup camera....etc won't function, I can lock the car but no beep sound, trunk won't open, air conditioning won't blow cold air......etc. I am suspecting is the JBE software error. Can you suggest the company that did the remote coding for you. After I get the part, I definitely need a professional code it for me so the car will back to normal.
Great video ! I’m experiencing some electrical issues too. Can you say more about what issues u were experiencing? Like was it completely no power, or were the buttons/switches not working?
My radiator fan won’t work and I have replaced two relays and checked the radiator heat sensor so I ordered a new fan and I was just hoping not to have to deal with that you got any suggestions?
Great video, thank you. My 08 528i has lost all power and I can't get the passenger door open. Any recommendations on how to open it so I can do what you did? Thanks in advance.
how many miles are on your car now? any other major issues besides from this one ? i have a 2011 328i x drive lci and i am having alot of suspensions and steering issues.
Hey JD, I found your channel trying to figure out why my CCC unit module stop working. I have no power to the CCC unit and no power to the display screen for my idrive. I just recently replaced the a/c heater blower fanin which I needed to remove the the CCC unit but when I reinstalled it. It just stop working. I have a dashboard message symbol SOS crossed out. Any pointer will be helpful at this point before I take it to the Stealership. I live in Boston.
How did you know what JBe to buy?? I am in same boat there’s a lot on eBay but not sure which to buy. Do they all work just need recoding? Why couldn’t your original just be recorded?
I’m looking at a 2007 328XI powers up just fine but when you hit the start button, nothing happens I’m wondering if I don’t have the same problem with that car as you have. I don’t wanna buy it if it’s gonna be a nightmare.
Hey I’m trying to do a DIY on a metal bar that broke on the rear of my bmw but I don’t know the name of the part, I was wondering if I sent you a pic or video you could tell me what’s it called ?
Any ideas y my drivers door and passengers door doesnt lock and y the sound comin out my idrive system only.sounds ok if i put it to the left sife of the car speakers and not the drivers side i put set it to all speakers the drivers side just pops and crackless ?
I'm trying to look for your old video see what was the electrical issue was but cant find? I'm having issue with the passenger aftermarket hid light would turn on then off. I would have to turn car off again for it to turn on but it does not remain on not sure if the ballast is going or some electrical issue as your?
I just got a 2003 530i and there’s major electrical issues like the door sensor and coolant low, and it says it needs service on the engine, and check engine lights on, check brake lights, but everything is fine, the car runs great, might even run better then my Honda accord 2007, but for I don’t know what is wrong with the electronics, I’m going to check tomorrow then right down the problems and try and erase them to see if they come back but if they do what will be the issue? Would I have to change the central electronics module?
So glad you finally fixed your car, man! But one question remains. What was the culprit that created this defect. Per my knowledge this JBE are not breaking by their own, intead it must be something that created a short circuit.
Hi , could you tell me how programming the new JBE? I have bmw standard tools. My module is still responding so i can make a "copy". May i copy that to the new JBE? thx for help
Hello friend's how are you? I have a BMW 520 2007. About 4 months ago when I start the car the eye browse start flicking 4 to 5 times and then it stops, after 4 weeks it shows on the dashboard that's daytime light on the right hand sideg it doesn't work, I checked it's ok not burned. it stayed the same. 10 days ago I was driving then I heard a banging noise, I stopped tornd the car of waited for a Koppel off minutes then I start the car the noise still there, the radio and the dashboard lights are off and the noise still making coming out of the speakers and it's annoying and all the lights on the left hand side are off. Have you came across this problem or anyone else's that's you know. I will be glad to hear from you. Thank you very much!
Hi great job !! i changed that to on my 630i e64 but it does n t start and electric windows and all the rest do not work .. do i have to code it ? Becaus you re was fixed after putting it in , no?
Would this module cause a A731 code to pop up? Says it’s the junction box, my car has a new battery but dies if I leave the lights on for 2-5 mins, it’s drawing power
dude, have you solved your problem? my car just did the same thing as yours, after bout one or two hours drive, my battery light comes out and slowly shut down my instrument cluster
@@JDCarsChannel The new F30 doesn't seem to have this JBE located on the same place... Is it the one on the back of the trunk to the right on top the battery?
Did the e90 have comfort access? I have had major problems with the comfort access. I think these jbe get shorted due to water leaking on the windshield seal. My SA showed me the cracked seal. I have most problems after a car wash. It sucks now my doors dont unlock at all accept with a key.
Very practical! Other than towing our boats and hauling lumber I use this car for everything. Even though its RWD it does fantastic in the snow with some good snow tires. I love this car.
If car have no power at all it has power connector problem quick check if you’re battery is charged only open a panel under gloves box and it is very hard to see red power cable connected to Fues panel just shake it little bit and you can got power it is recall on some bmw models You can check online (bmw recall) and put your win number Good luck
PLEASE SEND ME THE NAME OF WHO DID YOUR REMOTE FLASHING. I HAVE A 08 328i CONV AND IT HAS QUIRKS i DO NOT UNDERSTAND. ONE HEADLIGHT OUT, SAT OR BT NOT WORKING, CRUISE OR TPM RESET
I have a 2008 750Li that will not go into sleep mode the push button light stays on the dvd navigation runs a thumbing sound is coming from the passenger side sub this is causing my battery to drain and I had to replace the ECU which the dealership said it was fried and the have no idea what could be causing these problems
I no longer have the clicking sound in glove compartment After I replaced my Black Starter Relay (Multipurpose) but my car wont start nor do i have power. I cant even use my Portable Jumper. I guess I will be doing this JBE replacement. 2011 Bmw 328i Base Model Sedan
PLEASE LET US KNOW WHAT TYPE of electrical problems u were having..thank u were your lights on and brakelites w/o turning off and ur wipers on all the time? please adivse..thanks
Before you buy a new junction box you should try putting old one on a radiator for a day or so. The problem with the j b module is if you have had a water leak or didn't know you had one water or moisture can get into the box making the electrics behave weird. You'll find once you've dried it out it will work perfectly. So long as none of the pins are corroded it will be fine and you'll save money buying and coding it. Trust me just like dropping a phone in puddle if you dry it properly it will work again 😊
People over here in Germany code their amber lights to be the running lights (which btw is illegal here) and you do it the other way around in the US :D
My fuel gauge, central locking ( the indicators flash and the car powers off but the actuators don't lock), air conditioning(cooling) and wipers do not work (wipers turn on and stop on the middle of the screen), The only code I get is a 5E5B DSC button code and A738 JBE power supply interrupted code. Everything else works. Is it a FRM or the JBE that is faulty?
@@SicSemperBeats I changed the JBE and I managed to get the wipers and fuel gauge working but it did not fix the central locking issue. I guess its because I replaced my JBE with the one that is not identical to the one from the car. Just look for the JBE that is identical to the one in your car.
@@boccamokg1829 Hmm i changed my jbe and got literally no change in my problems. I even coded it to my vin through winkfp and checked through inpa. Did your wipers and gauge just automatically start working after you installed the JBE?
@@SicSemperBeats Yes, before they were not working at all and once I installed the JBE from a 2010 M3 they just started working without any coding or anything. Are you sure the JBE you installed is identical to the one you removed? If its an H3 it has to be an H3 you install and also the production date should match since it seems they changed the arrangement of the relays inside the circuit board over the years.
So what was your display reading before this replacement? Mine says DSC malfunction, DBC malfunction, malfunction in engine, malfunction in transmission and start off assistance off.
So how much did this whole fiasco cost you? How did it happen again? You said something about testing voltage and ambient lights but still didnt get "how" it happened.
Got my sub brother! I own a 2011 328xi. Been having some issues with the Electrical fault error showing up. (The car on the T stand looking icon). I’m hoping it’s just a bad battery but if not I’ll have to dive into the other electronics. Wish me luck!
How did you know which JBE to buy? I’m having the same issues with my FRM and JBE but I have yet to find any definitive information on which JBE is compatible with my specific car. Any help or guidance is greatly appreciated. Thank you
Definitely worth checking your JBE! If you find one on eBay that accepts returns, you can try it out for free (minus return shipping if you don't need it).
Bro .. I want to thank u!!! I was doing a retro cic swap, and I didn't disconnect the battery. 😢. I touched the monitor wires together during the swap. Then bam all hell breaks loose. Wipers turn on full speed, whinnying noise from my firewall, no electronics in the interior. But my car did start. But I couldn't control my headlights from being on. Man I just wanna thank u really 🎉. Did the swap step by step as u the walla. Thumbs up bro
Im having a simular problem with mine but it just came out of nowhere
You actually do a great job editing and showing components and how to remove close up, thank you
I found your channel yesterday, and watched a lot of your videos. When I saw video "My BMW is dead..", I said, omG, it's not happening. Than I watched this video where you repaired the car. It's so nice to see how much time you spent upgrading your BMW, and thank you for showing everything like DIY videos. I just want to say, thanks dude, it's pleasure to watch your videos. Best regards from Bosnia and Herzegovina.
Thanks Emin! That means a lot to me, and it's comments like this that keep me going!
love the genuine excitement of the outcome in real time. We all know that moment when it actually works! great video
Awesome video man, you film and explain everything perfectly. Really concise and informative.
What were the initial electrical problems?
The junction box electronics unit detects the following signals and makes them available to other bus users: Power window switch, front passenger door. Power windows switch, right rear door. Power window switch, rear door on driver's side.
@@8203ravikumar what about rear lift fog light and trunk light ..trunk central lock.. are it related to that JBE ?
@@8203ravikumar Great answer Sir. thanks for sharing with us!!!👏👏
Did your lights go out too and lose interior lights and cand lock car or alarm
Get a lighting system failure on screen
What electrical issues were you having before? I’m having wipers being stuck.. parking brake light illuminates when driving even tho brakes are brand new and hand brake down.. passenger seated seats don’t stay on.. they turn on them go off. My tach sometimes doesn’t show gas meter. And my Speedo goes from whatever speed I’m driving at than drops to 0 than returns to my current speed. And my rear passenger windows cut out when rolling up or down got hit the button again to continue
Fixed?
Glove box removal is just 2 torque 20s and a phillips for 4 screws holding onto bracket.
Hey mate .
My bmw e90(316d)(2009) is showing yellow engine light which come up time to time. I get it checked with ISTA+ unable to communication most gatway.
Unable to communicate to head unit.
What could be the problem, is it big problem please guide me.
Thanks
Anil
When you had no power did your key get stuck in the socket
Dude hell yeah! Electrical problems are the worst. Glad she's back.
They are the absolute worst. Glad to have her back!
@@JDCarsChannelmy lights flicker when I put key in the ignition and brake lights stay on after turning car off fuse box also makes noise when I put key in would u happen to know what it could be? Thanks
Did u get slotuion same as me wen i want to swtch on car its auto i put key in n press brakes then after 10sec it starts@@Everybodyshinetogether1
Where did you send off your ECU and CAS to get tested see if they are working properly or needed replacing? My car is getting some lights on but none on dash nor starting. Window buttons not working nor radio power. Battery is new
I have a 2008 and I don’t have a screen near my air-conditioning loves did you install that?
Hi there, my 2011 F10 535i got the similar electrical issues. All in a sudden my windshield wipers will go on and off itself randomly. Then my alarm, locking system, backup camera....etc won't function, I can lock the car but no beep sound, trunk won't open, air conditioning won't blow cold air......etc. I am suspecting is the JBE software error. Can you suggest the company that did the remote coding for you. After I get the part, I definitely need a professional code it for me so the car will back to normal.
MyBimmerBrain does all of my coding
I have 2011 bmw keeps blowing f37 fuse any input would be greatly appreciated
So sick dude congrats on the fix! Cool that it only cost you 60 bucks, glad you got your ride back!
Thanks man. Yes, I'm hyped to have it back!
Hello mate, and you don't have to code it, when does the JBE module change?
the new bcm, did you have to program it? Or just install a new one and that's it?
Very helpful...need to access the his to add linbus wire for heated seat...didnt know how to access it !!
Great video ! I’m experiencing some electrical issues too. Can you say more about what issues u were experiencing? Like was it completely no power, or were the buttons/switches not working?
Does the module have to be exactly the same mine has the jbbfe3 would a jbbfe2 work?
Yo where did you get those splitters?
I can't seem to find the jbe there is a air bags in its place
Would happen to know if this module can create interruption in 4*4 system co apparently ECM is not communicating with ECU in my e92 328 xdrive .
I have no idea to be honest. Sorry.
Did u ever find that out ecm not communicating with ecu
May I know what the symptom jbe bad?
I’ve currently got a rear light issue where my passenger side back DRL isn’t working could replacing the junction box solve it?
When replacing this module do you have to have the battery disconnected? Also if I pick one up from a used bmw would I have to code it as well?
Yes, that is a good precaution to take.
The module can be coded by MyBimmerBrain
My radiator fan won’t work and I have replaced two relays and checked the radiator heat sensor so I ordered a new fan and I was just hoping not to have to deal with that you got any suggestions?
Great video, thank you. My 08 528i has lost all power and I can't get the passenger door open. Any recommendations on how to open it so I can do what you did? Thanks in advance.
I recommend contacting MyBimmerBrain for assistance
Can I get a second hand jbe from the same year and model BMW and plug and play?
Does this cause battery drain cause I’ve been having this issue for over a year now
how many miles are on your car now? any other major issues besides from this one ? i have a 2011 328i x drive lci and i am having alot of suspensions and steering issues.
I have 191k now.
Hey JD, I found your channel trying to figure out why my CCC unit module stop working. I have no power to the CCC unit and no power to the display screen for my idrive. I just recently replaced the a/c heater blower fanin which I needed to remove the the CCC unit but when I reinstalled it. It just stop working. I have a dashboard message symbol SOS crossed out. Any pointer will be helpful at this point before I take it to the Stealership. I live in Boston.
I have the same problem did you figured it out
???
Is water pump related to the junction box?
How did you know what JBe to buy?? I am in same boat there’s a lot on eBay but not sure which to buy. Do they all work just need recoding?
Why couldn’t your original just be recorded?
oh yea, one more thing. What was the cost of JBE Module
It would be nice to see why not how. Why u think JBE is the cause? What was the troubleshooting logic? Did u trace the problem back to it?
That was a brand new or used jbe?
Where did you get the headlights from
I’m looking at a 2007 328XI powers up just fine but when you hit the start button, nothing happens I’m wondering if I don’t have the same problem with that car as you have. I don’t wanna buy it if it’s gonna be a nightmare.
Hey I’m trying to do a DIY on a metal bar that broke on the rear of my bmw but I don’t know the name of the part, I was wondering if I sent you a pic or video you could tell me what’s it called ?
Sure... you can contact me at www.jd-cars.com
What why the car doing? Was is not cranking at all?
could this module cause mhd flashing issues??
what codes was the car throwing?
What code should I respect when I change it ? Tha H2 code?
I am glad you fix your car man
Thanks brotha
between pin 5 and 6 left bottom is that rot from a blown pin.
Did the jbe require any programming or was it a plug and play?
Yes, it required VIN coding
@@JDCarsChannel ty
Any ideas y my drivers door and passengers door doesnt lock and y the sound comin out my idrive system only.sounds ok if i put it to the left sife of the car speakers and not the drivers side i put set it to all speakers the drivers side just pops and crackless ?
Would a bad jbe cause No power to the radio/idrive fuse ?
It could! I would check all fuses in your fuse box first
Hello jd I'm dealing with the same issues. I would like to get the business that remotely coded your bmw. Thanks
MyBimmerBrain helped us with our remote coding. He's a pro. Wishing you the best of luck with your issues!
Does the FMR has to be coded to your car as well?
Yes you have to clone it. He did say on video he took the help from mybimmerbrain who did it remotely
I'm trying to look for your old video see what was the electrical issue was but cant find? I'm having issue with the passenger aftermarket hid light would turn on then off. I would have to turn car off again for it to turn on but it does not remain on not sure if the ballast is going or some electrical issue as your?
That sounds like a ballast to me.
I just got a 2003 530i and there’s major electrical issues like the door sensor and coolant low, and it says it needs service on the engine, and check engine lights on, check brake lights, but everything is fine, the car runs great, might even run better then my Honda accord 2007, but for I don’t know what is wrong with the electronics, I’m going to check tomorrow then right down the problems and try and erase them to see if they come back but if they do what will be the issue? Would I have to change the central electronics module?
So glad you finally fixed your car, man! But one question remains. What was the culprit that created this defect. Per my knowledge this JBE are not breaking by their own, intead it must be something that created a short circuit.
This happened due to voltage testing behind the dash. It shorted the module.
@@JDCarsChannel I did a diagnostics and it says this would this make your car idle bad if u need to fix it?
Hi , could you tell me how programming the new JBE? I have bmw standard tools. My module is still responding so i can make a "copy". May i copy that to the new JBE? thx for help
I’m not exactly sure- I had MyBimmerBrain recode my modules
@@JDCarsChannel thanks for your answer. I changed the jbe and no need to recode. regards
Hello, you swapped jbe but didn’t have do not coding? Was it off same year model car
@@robertkenney6002 I don't remember...
Is the jbe plug and play? Can I find one off a donor car? Same year and model and plug it in?
Plug and play to an extent... it still needs to be VIN coded to the car
Is that something a scan tool can do like a fox well ? Or the new launch crew reader for bmw ? Thanks I’m going to source one somehow off an 09 335i
Hello friend's how are you? I have a BMW 520 2007. About 4 months ago when I start the car the eye browse start flicking 4 to 5 times and then it stops, after 4 weeks it shows on the dashboard that's daytime light on the right hand sideg it doesn't work, I checked it's ok not burned. it stayed the same. 10 days ago I was driving then I heard a banging noise, I stopped tornd the car of waited for a Koppel off minutes then I start the car the noise still there, the radio and the dashboard lights are off and the noise still making coming out of the speakers and it's annoying and all the lights on the left hand side are off. Have you came across this problem or anyone else's that's you know. I will be glad to hear from you. Thank you very much!
Hi great job !! i changed that to on my 630i e64 but it does n t start and electric windows and all the rest do not work .. do i have to code it ? Becaus you re was fixed after putting it in , no?
The car should start without coding. Ask MyBimmerBrain for assistance
Would this module cause a A731 code to pop up? Says it’s the junction box, my car has a new battery but dies if I leave the lights on for 2-5 mins, it’s drawing power
that hand is very important, I couldn't understand anything you said without it.
Great BMW information! I've subscribed to your channel.
Hey I get no power to fiber optic chasing down this no sound problem but head unit works. Could it be this ?
ok so quick question , what symptoms did you get for a bad JBE , deadlock immobilised car???
See my previous electrical problem video.
Im expecting that JBE module would cause the high battery discharge warning also, might be thinking of replacing that part
Did you ever get that figured out i been dealing with high battery discharge as well. Did you fix that issue? If so how
What was the original issue? My bmw has been loosing all power driving down the road from time to time.
I had TONS of electrical issues before the JBE replacement. Check previous video for more details.
dude, have you solved your problem? my car just did the same thing as yours, after bout one or two hours drive, my battery light comes out and slowly shut down my instrument cluster
Did My Beamer Brain tell you the problem was a bad JBE Box or did you figure that out on your own? Thanks for the info and congrats on the car fix.
MyBeamerBrain affirmed the suspicions I had that it was the JBE. Thanks!
@@JDCarsChannel The new F30 doesn't seem to have this JBE located on the same place... Is it the one on the back of the trunk to the right on top the battery?
how long did the coding take for the FRM and the JBE?
Less than an hour
Did the e90 have comfort access? I have had major problems with the comfort access. I think these jbe get shorted due to water leaking on the windshield seal. My SA showed me the cracked seal. I have most problems after a car wash. It sucks now my doors dont unlock at all accept with a key.
It did have basic comfort access. I had locking issues too. Your JBE may be shorted out.
@@JDCarsChannel thanks for the info!
I'm interested in getting a used 328i, and live in the Northeast. How practical of a car is it year-round?
Very practical! Other than towing our boats and hauling lumber I use this car for everything. Even though its RWD it does fantastic in the snow with some good snow tires. I love this car.
Are there any more mods planned for the e90?
Yessir!
Did you have to reprogram the JBE?
The same question!
If car have no power at all it has power connector problem quick check if you’re battery is charged only open a panel under gloves box and it is very hard to see red power cable connected to Fues panel just shake it little bit and you can got power it is recall on some bmw models You can check online (bmw recall) and put your win number
Good luck
Where do I find the coding buy ?
PLEASE SEND ME THE NAME OF WHO DID YOUR REMOTE FLASHING. I HAVE A 08 328i CONV AND IT HAS QUIRKS i DO NOT UNDERSTAND. ONE HEADLIGHT OUT, SAT OR BT NOT WORKING, CRUISE OR TPM RESET
hello , how do you find identical safotware to code frm ?
is it alradey in inpa , ncs expert tool ?
I had MyBimmerBrain do the coding remotely
I have a 2008 750Li that will not go into sleep mode the push button light stays on the dvd navigation runs a thumbing sound is coming from the passenger side sub this is causing my battery to drain and I had to replace the ECU which the dealership said it was fried and the have no idea what could be causing these problems
I have BMW X1 E84
Total Electrical system off so how to solve
Glad ya got it sorted bud 🤜🤛
Thanks brotha
I no longer have the clicking sound in glove compartment After I replaced my Black Starter Relay (Multipurpose) but my car wont start nor do i have power. I cant even use my Portable Jumper. I guess I will be doing this JBE replacement. 2011 Bmw 328i Base Model Sedan
PLEASE LET US KNOW WHAT TYPE of electrical problems u were having..thank u were your lights on and brakelites w/o turning off and ur wipers on all the time?
please adivse..thanks
i have this same issue, i think its the CAS module causing it, did you figure out what was causing it?
so what was the issue to begin with?
Hi JD cars could you tell me where can I buy the new JBD
Before you buy a new junction box you should try putting old one on a radiator for a day or so. The problem with the j b module is if you have had a water leak or didn't know you had one water or moisture can get into the box making the electrics behave weird. You'll find once you've dried it out it will work perfectly. So long as none of the pins are corroded it will be fine and you'll save money buying and coding it. Trust me just like dropping a phone in puddle if you dry it properly it will work again 😊
After replacement, programming needed?
Did it?
People over here in Germany code their amber lights to be the running lights (which btw is illegal here) and you do it the other way around in the US :D
Hahaha pretty funny
Amber lights disappear with a low sun behind.
Why did u swap it what were the symptoms
Most electrical components were not working (instrument cluster, windows, windshield wipers, climate control, etc.)
My fuel gauge, central locking ( the indicators flash and the car powers off but the actuators don't lock), air conditioning(cooling) and wipers do not work (wipers turn on and stop on the middle of the screen), The only code I get is a 5E5B DSC button code and A738 JBE power supply interrupted code. Everything else works. Is it a FRM or the JBE that is faulty?
Hey brother did toy get this fixed? Was it jbe? Also did you have it coded?
any update i get the same symptoms and code on my 335i
@@SicSemperBeats I changed the JBE and I managed to get the wipers and fuel gauge working but it did not fix the central locking issue. I guess its because I replaced my JBE with the one that is not identical to the one from the car. Just look for the JBE that is identical to the one in your car.
@@boccamokg1829 Hmm i changed my jbe and got literally no change in my problems. I even coded it to my vin through winkfp and checked through inpa. Did your wipers and gauge just automatically start working after you installed the JBE?
@@SicSemperBeats Yes, before they were not working at all and once I installed the JBE from a 2010 M3 they just started working without any coding or anything. Are you sure the JBE you installed is identical to the one you removed? If its an H3 it has to be an H3 you install and also the production date should match since it seems they changed the arrangement of the relays inside the circuit board
over the years.
So what was your display reading before this replacement? Mine says DSC malfunction, DBC malfunction, malfunction in engine, malfunction in transmission and start off assistance off.
I’m having similar issues, you find a resolve?
@@testedaustin418 ???
No love?
So how much did this whole fiasco cost you? How did it happen again? You said something about testing voltage and ambient lights but still didnt get "how" it happened.
In total, it cost me about $450... it happened due to the modules getting a small amount of voltage during testing. It fried them.
Got my sub brother! I own a 2011 328xi. Been having some issues with the Electrical fault error showing up. (The car on the T stand looking icon). I’m hoping it’s just a bad battery but if not I’ll have to dive into the other electronics. Wish me luck!
Thanks man! Good luck with your electrical issues - I know they’re not fun!
did you figure it out?
AWESOME VIDEO MANNN you honestly save me so much money with your videos man keep up the great content coming :))))))
Thanks bro! I'm glad the videos help!
How do I fix blinker issue it's blinking too fast have the same headlights you have and my right passenger side
In my case, it was a new JBE but it's tough to say without seeing the car. I recommend scanning it for codes
@@JDCarsChannel I did but it's showing no codes going to try the to change the fuse to it hope that works
Does this part need programming after installing??
Yes
How did you know which JBE to buy? I’m having the same issues with my FRM and JBE but I have yet to find any definitive information on which JBE is compatible with my specific car. Any help or guidance is greatly appreciated. Thank you
I just searched my year and mode “JBE” on eBay and that was it! It should tell you in the description which years it’s compatible with
05 to 08 fits 08lci to 11 fits because of different canbus signal
@@JDCarsChannel and you did not have to code it to the vehicle in any way?
Btw. What kind of head unit do you have
Many electrical problems- the JBE fixed her right up. That’s an Eonon unit. Check out our Eonon installation and review videos!
Hello how can I get to the BMW coding guy?
My 525xi bmw under the hood f01-f05 no power fuses not blown.
Hey thanks for this! Did you replace the FRM as well or just the JBE?
fantastic work!!!!!
Thanks!
I’ve lost power to windows, door locks, gauge lights, signal on inside, sunroof, and radio.. Any ideals?
Definitely worth checking your JBE! If you find one on eBay that accepts returns, you can try it out for free (minus return shipping if you don't need it).