Thanks guy! Just replaced my battery and didn't even know you had to do this. Your video just happened to pop up when researching how to replace battery.
Thanks for the video. We bought one in 2019 and the Ford dealer ominously said they make all their money on maintenance, so I immediately knew I'd never go back there. (120$/hour for pressing light switch and brake pedal etc is nonsense money making design scumbaggery).There is nothing in the manual about this reset deal, and the Battery Monitoring System does not warn you the battery is dying or not charging, god bless the designers who got fired for making older cars too good.
2017 Ford escape Titanium 2 ltr turbo, new battery installed. Tried doing this five times but doesn’t blink battery indicator. Thanks for the information though.
Just had a new battery put in, then noticed that some of my aftermarket accessories kept giving low voltage warnings. Got out my multimeter and could only get 12.6v max when charging. By chance happened to find this video, tried it on my 2015 escape and voila... 14.4v charging again. Thanks!
Just when I thought TH-cam was full of hokey stuff, this video actually proved useful and helped me out. Got my battery changed amd the windows would not roll up or down with a single press of the button. This method got it to work. Greag video. Short and to the point.
Yes sir same thing right here and I even did what the manual said to do which was the most stupidest thing to do which I did and knew it was stupid but I had to try it,what they said to do while in park put the emergency brake on start the car release the parking brake then drive for about 10 miles and then let it sit for 8 hours lmao,apparently we are dealing with morons like Biden.
Thank you for sharing this video. I swapped a new battery on my Ford escape 2014 I did everything by instructions as on video. I got to work. Thank you so much.
This works for a 2017 Ford Focus as well. My transmission interlock wasn’t working until I did this. If you can pull it out of pro without pressing the brake you need to do this
Thank You! I was about to go to the dealer to have this done because I read that only the dealer could do it with a scan tool. Now I know what to do and saved a trip to the Ford dealer. 👍👍
This worked in a North American Ford FIesta ST (2014, but I assume non ST and other similar models it is the same procedure) however I should note, on my car, the high beams switch has a half-way point where it will toggle on temporarily and then off when you release it, and if you do it that way it doesn't work, you need to a FULL pull of the lever so it toggles and stays on, then toggles and stays off (5x, then brakes 3x).
For those people that this method does not seem to work, make sure the hood, all doors, and rear hatch are all closed. I was pulling my hair out when I could not get this method to work after changing the battery on a 2016 Ford Edge, but the method worked when I closed the hood.
Thanks for the tip. Forscan doesn't work, I have tried it to reset the BMS on my new battery, and it simply doesn't work. Could be my adapter. This is nuts, but I believe it is correct. And if you don't do this, your vehicle will just start acting weird; such as Intelligent Access not working, doors not locking after 5MPH, weird flashing issue with some interior lights. It will literally take power away from accessories, such as your power windows. Stupid system.......Gotta do it apparently. Otherwise it keeps the old battery profile. Are cars this stupid? My god, plug and play has been a thing on computers since Windows 95 launched all those decades ago. Whatever computer controls the system should know if a new battery is in, or Ford is just monkeying around here.
Mine died today. Luckily in town on a sunny day and not in the winter on a isolated road. Console was lit up and wouldn’t turn off. Key not found message was displayed. Car wouldn’t start. We walked to a store to change key fob batteries just in case that was it…we could take the car out of park. The brake wouldn’t depress. Something is def wrong. It’s been towed to Ford.
Hello Susie. Have you remedied your lit console. OUr 2014 Escape drains the battery because the instrument panel cluster/LCD screen does not power down.
Never have changed my battery but this message popped up all of a sudden. Battery shows 12v so I don't know why. Never in 6 yrs . I tried it today we will see how this goes. Fingers crossed.
How is it going? Mine reading 12.5 when off and alternator is charging at 15.1 while driving, I replaced the alternator new , but used old battery. I just installed a new one last night and 15 mins into my 35 min drive home battery light comes on.
I did these exact steps and then after I take the key out of the ignition and try to start it, nothing. The battery goes dead and no lights or anything. Then I unhook the battery and repeat previous steps and same result. Thoughts?
2017 Escape...tried it every which way, door open, door closed, waited for the dinging to stop before doing, did it immediately upon turning the key on, etc. (5 times) and could not get the battery light to flash...Canadian car, not sure if that matters
@@fupabox yup strange!...I ended up giving it back to my mother as is. She hasn't reported any issues so far....also I read somewhere from some youtuber who copied a page out of a Ford service manual that said the BMS needs 8 hours of "sleep time" after you change batteries to reset itself. So maybe that's what mine needed?? who knows! so far so good..
@@fupabox could the issue be the remote start option? I have a 2016 fusion se 2.0 ecoboost with remote start so I’m hesitant to change the battery on my own and try this if I’d just need to bring it in to be reset anyway
Been a year since I put a new battery in on 2019 Ford Fiesta SE and have been having a problem with master window switch not opening the rear windows. And the switch doesn't illuminate. I've tried new fuses and still the rear windows won't open from the master switch. Could this help?
Thanks. We'll see if I get to listen to music more than 30-40 minutes before the stingy thing shuts me off. (The odd part is that I only need to start the van for 30 sec and I get another slot of time. So the "BMS" is either only a timer or is lying.)
I tried this on a 2019 Escape SE fwd. All doors, hood, and hatch closed. All accessories off. 5x flashes, 3x brake, no luck to get the brake light to flash/confirm.
Same method . Just don’t have your foot on the brake when you hit the start button and the car will turn everything on , but not start . Then you do the 5 high beam flashes , brake pedal press etc . Any time you need the ignition on but not have the car started , just push the button without your foot on the brake pedal .
And what if you do this but the battery light doesn't ever blink? My 2017 Ford Escape will crank up but it keeps dropping below a 1000 rpms and then dies. Any clue as to what might be wrong?
I really wish I knew . A small % have no luck with the reset . Ford should be ashamed for over complicating a battery swap . I am currently researching an answer as another neighbour has the same issue as you do . Fingers crossed 🤞
I was wondering if I’d be able to do this wit a booster pack hooked up to the battery because i can’t start my ford without and jumpstart and right when i shut the car off the battery dies instantly i don’t have any power in the car until i hook the booster up
Confirmed working on a 16 Fusion with old BMS monitor on the cable and MyFordTouch. Light will blink for about 5 seconds before disappearing like shown.
I tried 3 different time with no change of the reset of the BMS reset on a 2018 Ford Escape SE with Eco boost so the person that states this works on all ford vehicles with the BMS. does not know what he is talking about and is giving false information.
I tried what the manual said to do it did not work what a joke.Whoever did this design is a moron no way to add water to this battery too.The idea is to let them install the battery so you get ripped off.A new battery is about 200.00 now so with their labor it might have been about 500.00 or more,lol
Just did this on my 2018 Ford explorer limited with push button start. Battery symbol flashed 4 times. Mine was never reset when the battery was installed a few months ago. Thanks
I’m not sure mine was I disconnected so it was like new? Did this trying to eliminate a problem . how far after your battery was put in did you do this? And did you disconnect it? I’m just curious I still have some problem I think is the ECM unit but any help is always awesome. Thanks.
Question - I just replaced the battery on my 2013 Escape and haven’t done this yet. But my airbag light has been coming on now. Could this be the trick to fixing that.? I’ve read the light can come on if the system feel the battery voltage drops below 12v..
Seriously Is it really that easy I have a 2018 Ford F150 that I need to replace the battery and dealer told me they could only do it with there machine. 🤔
Pretty sure Ford put this feature in so you have to go visit and pay the dealership to swap batteries or trouble shoot electrical problems with their cars rather than doing an easy swap yourself (or through a cheap mechanic / handy buddy etc).
Actually the opposite. They could have made this so only the dealer could do it with their own special tool. This is clearly an "anybody can do it" procedure. The only thing that would be better is if it was documented in the owner's manual.
@@timinater they would have documented it and let people know if that was the case. Otherwise it's just creating more problems for people. That's my experience anyway. Replaced the original battery likely 7 years old and like a year or two later the new battery is already dead.
Hello, I tried this in my titanium ecoboost 2017, it worked, but now, when the car turns on after a stop feels like a kick in the motor, is that normal? How can I correct that?
Sometime car don't start , when remove terminal and put terminal again then start , so its the BMS problem that the car computer system don't recognise the new battery which I install a month a go ?
I am hoping someone is still monitoring this video and the comments. I have a 2014 Ford Escape that required a jumpstart this weekend. Come to find out, my trunk did not latch all the way after loading some stuff up to move, and it drained the battery. Have had no issues prior to this with the battery to indicate that the battery is shot or needs to be replaced. HOWEVER, ever since the jumpstart, my clock is frozen and will not allow me to change it. My question is, will this work (or possibly work) even if I have not had a new battery put in but have just had a jumpstart?
I don't think it would harm anything to try resetting the BMS. One thing you could try if it continues being a problem is disconnect the negative battery terminal for a few minutes, then reconnect and perform the BMS reset procedure in the video.
@@fupabox I hope this fixes mt issue ive replaced both wiper motors on my 2016 escape now ive spent 300$ in the past year on wipers because they end up colliding when snow ways on them.
Interesting that they have these alternate methods available that don't require the factory scan tool, im guessing probably a legal requirement. The first time i heard about this telling the car the battery was new was when the dealership installed a new AGM battery in my ford. It's an employer issued car so i never have to do anything with it other that drive it.
It seems like a pointless system to me . Neighbors car had a constant dead battery every morning after a new one was installed, no dead battery any more . The BMS seems to want to know if it’s a new or old battery in order to charge properly . Voltage regulators have always done that without the need for this silliness . Sometimes newer isn’t always better .
@@fupabox mine also has the stop start, i just assumed it was to do with that to ensure the constant stopping and starting wouldn’t leave you stranded in traffic. quite a ridiculous feature, in stop start traffic you pretty much have no choice but to disable it.
![[UNCUT]"ตุลามรณะ"ย้อนฟังคำทำนาย หมอดูทุกสาย ดวงเมืองร้อน (หมอปลาย ฟองสนาน อ.โอเล่)I คนดังนั่งเคลียร์](http://i.ytimg.com/vi/lE5az5VvT9M/mqdefault.jpg)
Thanks guy! Just replaced my battery and didn't even know you had to do this. Your video just happened to pop up when researching how to replace battery.
Yeah, how the heck is the average owner supposed to know about this?
By not resetting this could it be the cause of random non starting.
Thanks for the video. We bought one in 2019 and the Ford dealer ominously said they make all their money on maintenance, so I immediately knew I'd never go back there. (120$/hour for pressing light switch and brake pedal etc is nonsense money making design scumbaggery).There is nothing in the manual about this reset deal, and the Battery Monitoring System does not warn you the battery is dying or not charging, god bless the designers who got fired for making older cars too good.
I thought this was something only the dealer could do. So glad I saw this. No need to pay a dealer $75 to replace a battery!
No but to replace it you have to do a bunch of other crap to get to it. Step 1 is take the windshield wipers off, seriously i did it yesterday.
No@@Libzarsupergae
th-cam.com/video/eMog06wr6y4/w-d-xo.html@@Libzarsupergae
I have a 2013 ford Escape with this very problem... It might sound crazy but it worked for me! Outstanding! Thanks!!!
2017 Ford escape Titanium 2 ltr turbo, new battery installed. Tried doing this five times but doesn’t blink battery indicator. Thanks for the information though.
Tried it on 2017 ford escape se 1.5 l turbo didn’t won’t to.
THANK YOU! I was terrified when my 2016 wouldn’t start up at all! You helped a ton!🎉
Glad it worked for you 🙏👍
Just had a new battery put in, then noticed that some of my aftermarket accessories kept giving low voltage warnings. Got out my multimeter and could only get 12.6v max when charging. By chance happened to find this video, tried it on my 2015 escape and voila... 14.4v charging again. Thanks!
You the man, this was driving me nuts for months. 15 Focus 1.0.
Just when I thought TH-cam was full of hokey stuff, this video actually proved useful and helped me out. Got my battery changed amd the windows would not roll up or down with a single press of the button. This method got it to work. Greag video. Short and to the point.
Glad it helped .
THANK YOU!!!!!!!!! 🎉🎉🎉 Have been going crazy trying to get my nephews car working. 2015 Focus SE.
thank you so much, fixed a constant charging error message on my GT350. dealer didn't do this when they put the new motor in and new battery
Kuga MK2 2013, worked first time. The battery flashed too. Thank you for the share.
Thank you for making this vid. I was completely stranded.
Tried this 3 times on my 2018 Ford Escape SEL and battery light never flashed.
Yes sir same thing right here and I even did what the manual said to do which was the most stupidest thing to do which I did and knew it was stupid but I had to try it,what they said to do while in park put the emergency brake on start the car release the parking brake then drive for about 10 miles and then let it sit for 8 hours lmao,apparently we are dealing with morons like Biden.
Thank you for sharing this video. I swapped a new battery on my Ford escape 2014 I did everything by instructions as on video. I got to work. Thank you so much.
This works for a 2017 Ford Focus as well. My transmission interlock wasn’t working until I did this. If you can pull it out of pro without pressing the brake you need to do this
Amazing!!!! Saved me lots of $ at Ford dealership. Thank you.
Thank You! I was about to go to the dealer to have this done because I read that only the dealer could do it with a scan tool. Now I know what to do and saved a trip to the Ford dealer. 👍👍
This worked for a 2015 Ford Focus Titanium X (UK) first time! Thank you!
This worked in a North American Ford FIesta ST (2014, but I assume non ST and other similar models it is the same procedure) however I should note, on my car, the high beams switch has a half-way point where it will toggle on temporarily and then off when you release it, and if you do it that way it doesn't work, you need to a FULL pull of the lever so it toggles and stays on, then toggles and stays off (5x, then brakes 3x).
Thank you SO MUCH for writing this a year ago. I have not seen this info for the hi beam switch anymore??
Thanks, you just saved me a trip to the dealer!
For those people that this method does not seem to work, make sure the hood, all doors, and rear hatch are all closed. I was pulling my hair out when I could not get this method to work after changing the battery on a 2016 Ford Edge, but the method worked when I closed the hood.
excellent info ..thanks
The book doesn't say anything about doing this.
Not working for me. Car is all shut and still not working. Any suggestions?
Not an issue with a 2015 Focus SE. Door open and hood up. Maybe it's the timing of the sequence? 🤔
didn't work for my 2017 escape se awd
Worked on my 2014 Focus SE. thank you!
Thanks for the tip. Forscan doesn't work, I have tried it to reset the BMS on my new battery, and it simply doesn't work. Could be my adapter. This is nuts, but I believe it is correct. And if you don't do this, your vehicle will just start acting weird; such as Intelligent Access not working, doors not locking after 5MPH, weird flashing issue with some interior lights. It will literally take power away from accessories, such as your power windows. Stupid system.......Gotta do it apparently. Otherwise it keeps the old battery profile. Are cars this stupid? My god, plug and play has been a thing on computers since Windows 95 launched all those decades ago. Whatever computer controls the system should know if a new battery is in, or Ford is just monkeying around here.
This worked...so far. Im hoping it continues. Thanks!
Glad it helped . Should be fine . The 3 I’ve done all worked perfectly with no issues afterwards
Worked in a 2020 Transit Custom, thanks!
Sometimes it doesn’t work right away, drive it for a day and then try the next day. This has worked for me .
Didn't work for me the first time. I'll try tm
Worked on my 2015 kuga (UK) THANK U
Does this work on the keyless push to start model?
Awesome, thanks. Works on 2018 Ecosport
Good to hear 👍👍🙏
Did this to reset my auto start stop and it worked. My battery light didnt flash though. And its working fine. American Escape
Nothing more annoying than that auto stop start feature.
Unfortunately, it did not work on my 2019 Titanium. But thanks for sharing this tip!
It’s odd that about 5% just don’t work . Ford has some explaining to do I think .
Did not work with my 2018 Escape SE. What did work was leaving the key in the ON position for 10 seconds before starting. This might help others....
Great info .. thanks 🙏
Before starting what? The vehicle or the process of reset?
@@madguitar1086 before I actually started the vehicle, after the battery was installed.
Mine died today. Luckily in town on a sunny day and not in the winter on a isolated road. Console was lit up and wouldn’t turn off. Key not found message was displayed. Car wouldn’t start. We walked to a store to change key fob batteries just in case that was it…we could take the car out of park. The brake wouldn’t depress. Something is def wrong. It’s been towed to Ford.
Hello Susie. Have you remedied your lit console. OUr 2014 Escape drains the battery because the instrument panel cluster/LCD screen does not power down.
ford focus 2016 works ,, awesome . THANKS !!🍺🍺🍺
Focus too ? Wow . Good info , thanks 🙏
Worked on my Ford Escape 2018
We have a 2018 Ford Escape too it did not work .
Doesn't work on my 2018 Escape SEL. I also tried the 10 second wait first.
Worked a treat
worked on my 2016 SE
Never have changed my battery but this message popped up all of a sudden. Battery shows 12v so I don't know why. Never in 6 yrs . I tried it today we will see how this goes. Fingers crossed.
How is it going? Mine reading 12.5 when off and alternator is charging at 15.1 while driving, I replaced the alternator new , but used old battery. I just installed a new one last night and 15 mins into my 35 min drive home battery light comes on.
Thanks,2011 f150 3.5 worked
Didn’t work for my 2019 ford escape
Great vid . Any tips on getting the key fob to work after replacing battery thanks
2016 escape..it worked..... thought you were joking! added pull my finger 3x haha
🤣👉
I did these exact steps and then after I take the key out of the ignition and try to start it, nothing. The battery goes dead and no lights or anything. Then I unhook the battery and repeat previous steps and same result.
Thoughts?
How does it work if your car is keyless? Thanks.
I’m sad bc it didn’t work on my 2017 Escape SE :(
Didn’t work on my 2017 Escalera either. Battery light never would flash.
2017 Escape...tried it every which way, door open, door closed, waited for the dinging to stop before doing, did it immediately upon turning the key on, etc. (5 times) and could not get the battery light to flash...Canadian car, not sure if that matters
It’s very weird that it works on some and not others . I have no clue as to why . Wish I had an answer . The car in the vid is in Canada as well .
@@fupabox yup strange!...I ended up giving it back to my mother as is. She hasn't reported any issues so far....also I read somewhere from some youtuber who copied a page out of a Ford service manual that said the BMS needs 8 hours of "sleep time" after you change batteries to reset itself. So maybe that's what mine needed?? who knows! so far so good..
@@fupabox could the issue be the remote start option? I have a 2016 fusion se 2.0 ecoboost with remote start so I’m hesitant to change the battery on my own and try this if I’d just need to bring it in to be reset anyway
Same with my 2017 Escape. Battery did not flash, I tried 3 times.
@@fupabox I believe it may not work on Ford Escape Titaniums.
Been a year since I put a new battery in on 2019 Ford Fiesta SE and have been having a problem with master window switch not opening the rear windows. And the switch doesn't illuminate. I've tried new fuses and still the rear windows won't open from the master switch. Could this help?
Mine only blinked twice. I think I may have had a door open or window down. I'll follow the tips to do that and try again.
Didn’t work on my 2017 Escape S.
Is this the same procedure on all ford makes
Ok I tried every method and nothing works my battery symbol never flashes.
Does this work on a ford focus se doesn’t have the fog light button
Thanks. We'll see if I get to listen to music more than 30-40 minutes before the stingy thing shuts me off. (The odd part is that I only need to start the van for 30 sec and I get another slot of time. So the "BMS" is either only a timer or is lying.)
What will happen if did not do this when new battery installed?
I tried this on a 2019 Escape SE fwd. All doors, hood, and hatch closed. All accessories off. 5x flashes, 3x brake, no luck to get the brake light to flash/confirm.
@fupabox i believe this worked for me as my car started fine but i didnt see the battery flash at all...
When did car repair start including the hokey pokey?
Steering wheel looks vastly different than mine which I have a 2017 SE model which did this to not work for
Same have US 2017 SE model, and it doesn't work for me either.
Thanks. What faults can it throw up if not reset plz?
Can you do this simply after disconnecting your battery (not replacing it)?
my 2017 ford escape does not have an ignition key, only push start. How do I reset the battery?
Same method . Just don’t have your foot on the brake when you hit the start button and the car will turn everything on , but not start . Then you do the 5 high beam flashes , brake pedal press etc . Any time you need the ignition on but not have the car started , just push the button without your foot on the brake pedal .
And what if you do this but the battery light doesn't ever blink? My 2017 Ford Escape will crank up but it keeps dropping below a 1000 rpms and then dies. Any clue as to what might be wrong?
I really wish I knew . A small % have no luck with the reset . Ford should be ashamed for over complicating a battery swap . I am currently researching an answer as another neighbour has the same issue as you do . Fingers crossed 🤞
I was wondering if I’d be able to do this wit a booster pack hooked up to the battery because i can’t start my ford without and jumpstart and right when i shut the car off the battery dies instantly i don’t have any power in the car until i hook the booster up
Confirmed working on a 16 Fusion with old BMS monitor on the cable and MyFordTouch. Light will blink for about 5 seconds before disappearing like shown.
I tried 3 different time with no change of the reset of the BMS reset on a 2018 Ford Escape SE with Eco boost so the person that states this works on all ford vehicles with the BMS. does not know what he is talking about and is giving false information.
I tried what the manual said to do it did not work what a joke.Whoever did this design is a moron no way to add water to this battery too.The idea is to let them install the battery so you get ripped off.A new battery is about 200.00 now so with their labor it might have been about 500.00 or more,lol
Do you think this would work for a 2012 Ford Focus ?
Will this work on a 2006 ford escape? 🙏
It doesn’t work for me. I don’t know why but I have tried everything maybe because I started the car before resetting the new battery?
Could not resetting BMS after battery replacement cause a battery terminal to corrode faster than it should?
Works on Ford C Max Grand 2014,ty!
I have a 2017 Ford escape se and the battery light didn’t flash but my engine light did. What does that mean?
from what I understand you have to reset it with Forscan and either cable to attach to.laptop and old port or via there Wireless module
Can I disconnect my battery… reconnect it and try this?
Last time I change out my battery my radio went out.
Now my AC is out.
Just did this on my 2018 Ford explorer limited with push button start. Battery symbol flashed 4 times. Mine was never reset when the battery was installed a few months ago. Thanks
I’m not sure mine was I disconnected so it was like new? Did this trying to eliminate a problem . how far after your battery was put in did you do this? And did you disconnect it? I’m just curious I still have some problem I think is the ECM unit but any help is always awesome. Thanks.
Would this process be the same on a 2018 transit custom if the battery underneath the seat got replaced 🤷🏻♂️
Possibly . Can’t hurt to try . Nothing can be damaged 👍
Sólo hay que pulsar las luces largas ???? Y esperar que el testigo de la beteria parpaedee?
Question - I just replaced the battery on my 2013 Escape and haven’t done this yet. But my airbag light has been coming on now. Could this be the trick to fixing that.? I’ve read the light can come on if the system feel the battery voltage drops below 12v..
It’s possible the airbag issue is related. Can’t hurt to try 👍
have a 2017 ford escape se new battery was installed I tried this to the tee it did not work?
This in no way works on a 2018 Ford Escape Titanium. I just installed a new AGM battery and it still indicates to install a new battery.
Seriously Is it really that easy I have a 2018 Ford F150 that I need to replace the battery and dealer told me they could only do it with there machine. 🤔
This worked for my 2014 Focus. Other methods from other videos did not get the correct result.
Currently trying this on my 2014 ford focus and have had no luck. What’s the trick?
Me too
What's the other methods , didn't work on 14 escape se
Bless you sir
Not working on a 2018 Escape SE. Trying to get Auto-start stop to work
saaaammmmme bruh
I suspect this may not work on any 2018 Ford Escapes.
Pretty sure Ford put this feature in so you have to go visit and pay the dealership to swap batteries or trouble shoot electrical problems with their cars rather than doing an easy swap yourself (or through a cheap mechanic / handy buddy etc).
Actually the opposite. They could have made this so only the dealer could do it with their own special tool. This is clearly an "anybody can do it" procedure. The only thing that would be better is if it was documented in the owner's manual.
@@timinater they would have documented it and let people know if that was the case. Otherwise it's just creating more problems for people. That's my experience anyway. Replaced the original battery likely 7 years old and like a year or two later the new battery is already dead.
@@timinater And not have the warning message display continually, even when the car is off. Sure way to drain a battery.
Hello, I tried this in my titanium ecoboost 2017, it worked, but now, when the car turns on after a stop feels like a kick in the motor, is that normal? How can I correct that?
Any problem if your Escape has Auto Start/Stop?
Believe it or not, it worked in my 2018 F150
Sweet . Excellent info 👍
Worked on my 2016 trend c max
Sometime car don't start , when remove terminal and put terminal again then start , so its the BMS problem that the car computer system don't recognise the new battery which I install a month a go ?
I feel like I'm being punked by this video because I couldn't make it work on a 2017 Escape.
😕
🇺🇸
It’s weird . It works for most , but on some vehicles it just won’t seem to do anything. I wish I knew why .
Weird. When I did this my engine light flashed, not my battery light.
Same
I am hoping someone is still monitoring this video and the comments. I have a 2014 Ford Escape that required a jumpstart this weekend. Come to find out, my trunk did not latch all the way after loading some stuff up to move, and it drained the battery. Have had no issues prior to this with the battery to indicate that the battery is shot or needs to be replaced. HOWEVER, ever since the jumpstart, my clock is frozen and will not allow me to change it. My question is, will this work (or possibly work) even if I have not had a new battery put in but have just had a jumpstart?
I don't think it would harm anything to try resetting the BMS. One thing you could try if it continues being a problem is disconnect the negative battery terminal for a few minutes, then reconnect and perform the BMS reset procedure in the video.
Will it hurt to reset BMS without changing battery? I have radio issues and I'd like to try this.
Nope . It can’t hurt anything to try it .
Thank you so much
Does this affect issues with wipers falling out of sync? I changed my battery a year ago and my wipers never worked right since then
Possibly yes . It can cause a lot of weird issues
@@fupabox I hope this fixes mt issue ive replaced both wiper motors on my 2016 escape now ive spent 300$ in the past year on wipers because they end up colliding when snow ways on them.
@@fupabox ever since I removed the wipers to change the battery they never worked the sameb
Thanks for information
Interesting that they have these alternate methods available that don't require the factory scan tool, im guessing probably a legal requirement. The first time i heard about this telling the car the battery was new was when the dealership installed a new AGM battery in my ford. It's an employer issued car so i never have to do anything with it other that drive it.
It seems like a pointless system to me . Neighbors car had a constant dead battery every morning after a new one was installed, no dead battery any more . The BMS seems to want to know if it’s a new or old battery in order to charge properly . Voltage regulators have always done that without the need for this silliness . Sometimes newer isn’t always better .
@@fupabox mine also has the stop start, i just assumed it was to do with that to ensure the constant stopping and starting wouldn’t leave you stranded in traffic. quite a ridiculous feature, in stop start traffic you pretty much have no choice but to disable it.
It didn't work on my 2011 ford escape what am I doing wrong?? Help!!
It worked !!! Thanks na lot !!!