I see you have a lot of the details of your farm figured out. But you mentioned you work with CF filaments sometimes. I'd advise you check carefully the exact filament you work with as a lot of CF filaments leave microscopic fibers on your hands when handling the spools, or actual prints which are like micro needles. You can figure out on your own how healthy it is if you accidentally aspirate those fibers that are flung into the air by the printer fans while working with CF related stuff.
I would recommend some good smoke detectors. I would also install some sheet rock over the exposed insulation and wood studs. I imagine a print farm has a higher risk of fire than most uses in a basement.
Great video. I like to see videos like this of people starting out with small print farms in their basements or garages. Question I have for you what are you doing about the noise level? I just got my 1st P1S and I was amazed at how loud these printers are. I can only imagine how loud having 12 of them would be.
For me, it's not a big deal. They're a floor below where I spend all of my time. You can year them from the room that shares a wall though. That said, there's no drywall on one side of that wall, and I'm sure installing it would dampen sound a bit. That wall also happens to be a staggered wall, and it's insulated since it was originally going to be a theater.
Thanks, will do! I still say I'm retired. So far, I've spent everything I've made on keeping up with growth. It's still a very small business, but I started with nothing and no funding, so it's truly been "bootstrapped".
I use the textured PEI plate. I was using before Bambu started shipping or standard. I like the convenience of it working with all materials I print. I also dislike the texture from plate plates because it seems to show more of the slight imperfections in the surface of the plate. The texture of the PEI plate is minimal, so it blends in ok while hiding minor imperfections in its surface.
I love your farm. I love to keep everything on 1 platform as well! New sub here 💪🏾
Thanks!
I see you have a lot of the details of your farm figured out. But you mentioned you work with CF filaments sometimes. I'd advise you check carefully the exact filament you work with as a lot of CF filaments leave microscopic fibers on your hands when handling the spools, or actual prints which are like micro needles. You can figure out on your own how healthy it is if you accidentally aspirate those fibers that are flung into the air by the printer fans while working with CF related stuff.
I would recommend some good smoke detectors. I would also install some sheet rock over the exposed insulation and wood studs. I imagine a print farm has a higher risk of fire than most uses in a basement.
I appreciate the input. I do have two smoke & heat detectors in the area. They also alarm through the whole house and shop if they're set off.
Great video. I like to see videos like this of people starting out with small print farms in their basements or garages. Question I have for you what are you doing about the noise level? I just got my 1st P1S and I was amazed at how loud these printers are. I can only imagine how loud having 12 of them would be.
For me, it's not a big deal. They're a floor below where I spend all of my time. You can year them from the room that shares a wall though. That said, there's no drywall on one side of that wall, and I'm sure installing it would dampen sound a bit. That wall also happens to be a staggered wall, and it's insulated since it was originally going to be a theater.
Could have sworn you said you were retired at some point, look pretty busy to me, amazing what you have done, great content.
Keep it up
Pat
Thanks, will do! I still say I'm retired. So far, I've spent everything I've made on keeping up with growth. It's still a very small business, but I started with nothing and no funding, so it's truly been "bootstrapped".
Thanks for a very informative video :)
May I ask what plate you use and why?
I use the textured PEI plate. I was using before Bambu started shipping or standard. I like the convenience of it working with all materials I print. I also dislike the texture from plate plates because it seems to show more of the slight imperfections in the surface of the plate. The texture of the PEI plate is minimal, so it blends in ok while hiding minor imperfections in its surface.
Great information. Thansk for sharing.
You bet! Thanks for letting me know.
What is your go-to filament for the P1S?
by the way, it was this video along with the Bambu printer sale that prompted me to buy a P1S.
@@jamesbutler4157 Awesome! I think you'll be very happy with it. If you have any questions or anything, just let me know.