ฝัง
- เผยแพร่เมื่อ 2 ธ.ค. 2015
- The HD version of the YakAttack LeverLoc Anchor Trolley includes backing plates for the Harken Pulleys and LeverLoc Clamp Base. One this video we show the installation process on a Jackson Kayak Cuda 14. Visit www.yakattack.us for more product information and to find a dealer near you.
![How To Re-Enter A Kayak In Deep Water [Standard & Trick Method]](/img/n.gif)
Thank you so much for taking the time to make an HD version and going through all of the details as you did. I have been trying to figure out how to install the HD kit but didn't know where to begin.
Just installed my Yakattack HD on my Lifetime Pro Angler 11’6” today !
Thank you for the tips! I put one end of the kayak on a saw horse and lifted same end as needed to get the cord to drop to the front end with the hatch access. The hatch on the forward end of the boat is the only access point.
Long shot but you have the exact kayak I do and I am hoping to ask for your assistance in installing this
@@TheMyrmidonSoldier I’d be glad to try to help
@@everyman2580 Did you just throw cord into the kayak from the rear and let the loose cord fall into the hull ?
@@TheMyrmidonSoldier I did, however I helped it along by tilting the ‘feeding end’ of the kayak onto a saw horse. The line then fed nicely to the opposite end of kayak.
Excellent instructional videos!
Thanks Joel!
Installing mine tonight
you need an obliging ferret to run inside, pull the cord and then run back to the hatch. neat set up though - despite the lack of ferret
Has anyone ever experienced the standard anchor trolley installed with screws tear out or is this just overkill?
Very good job.
Thanks Brad!
I'd like to see a video on all the camera mounting options available using YakAttack products. Thx!
Could you use marine grade pop rivets instead of the machine screws to fasten the pulleys in place?
Good grief, 11:00 in and I'm wishing I would have purchased the basic anchor trolly...
Close-ups would be extremely helpful when showing alignment of parts.
The kayak I am installing the kit on has a thin and curved side gunnel and the angle change above and below the chine is large. Because the LeverLoc base is flat and is only fastened to the boat at two points on the top, on a curved surface it does not contour and the gap for stowing the ring becomes too large and ineffective. Is there anything that I can do about this, for example, installing the LeverLoc base below the chine where the hull is more vertical? I am not sure how this will affect the performance of the trolley, as you say in Episode 3 (the standard kit) to install the base above the chine.
Great Video...what diameter paracord did you use? Thanks
Why would somebody chose the hd kit over the standard kit? I just ordered the standard kit and am curious if I should go ahead and get the backing plates for my install
DON'T take the nuts out of the backing plate. You will rue the day. Inevitably a nut will fall out when you try to make your final connection, and guess what? You get to start all over again. Carefully mark the holes. Double check. Then drill.
should only take it off on one of the backing plates and use that to make the holes.. Then once they are in use the one you took off the back nuts on the one you can have easy access to.. sorry if I confused the crap out of people but this worked for me.
Would using two different color bungee cords make things easier to determine which bungee relates to which hole?
That is a solid idea and would be a sure fire way to determine which bungee is which. Thanks for the suggestion.
Looking for ways to attach the anchor to the trolley system. No shows that .
Where can i get a YakAttack decal like the one on the rear of the yak? Only see the new logo on the site. Thanks
What did you do with the two extra pad hooks? Did you space them evenly for a total of four pad hooks?
+BGyakinKansas We only installed 2 PadHooks on this boat. The line sat well with only two, but we might go back after some time on the water and add the two extra PadHooks.
I might have missed it but do I need backing plates on the line guides? Also, any suggestions for doing this install on an outback would be really appreciated. BTW YakAttack customer service is on point! Means a lot!
The backing plates are intended for the two pulleys and the LeverLoc base. Most of the pressure applied while anchored is directed to the two pulleys. Have you purchased the LeverLoc HD Anchor Trolley already and what type of water do you fish? Also, thank you for the kind words. The kayak fishing community and our customers are the most important thing to us so we will do what it takes to make sure their needs are met.
Why did I buy the HD..? Should have purchased the basic anchor trolly...
Are the screws to fill the holes smaller ? Or should there be 9 screws the same size in a kit ?
The third screws for the pulleys and LeverLoc, use only if you need to use a Rigging Bullet for the install, are shorter in length than the other two screws.
What if you have a styrofoam Block in the front?
Does the kit come with the bungee to pull the backing plate inside the boat?
Bungee or the 10-32 YakAttack Rigging Bullets are not included with the kit.
How about a video on this anchor trolley system on a 2015 coosa hd?
+Rob Raccuglia i will be installing 2 of them on a pair of HD's next week and will share the video when i am done. hope that will help some folks.
What a minute ...why do I need backing plate ? I thought I ordered the standard version. Is it necessary ? I have no access to inside of the kayak as I have a perception outlaw sit on top . Should I order standard kit instead? Is there a possibility of damage to kayak if backing plate is not used ?
The vast majority of customers use the standard kit. The HD kit with the backing plates is for those who tend to anchor in rougher water, current, or wind.
really the HD seems to be the fix for for the regular anchor trolley did i screw up buying from Yak Attack!!
The standard kit outsells the HD by a long shot. The HD is designed for those in the toughest conditions and the standard kit works for 95% of anglers.
The Big Fish 105 does not have access hatches. I guess that means only the standard kit willl work.
The standard kit is our #1 seller and fits the needs of the vast majority of kayaks anglers.
How can I install this hd kit into a lure 13.5. It didn't have any hatches in the rear at all. Can't see a way to get a backing plate all the way to the rear.
Edit: actually I think I figured out one way. I'll stand it up on its nose and let gravity feed the cords to me lol
For future installs on kayaks that have limited access check out this video that talks about the YakAttack Rigging Bullet. One trick that isn't shown in this video is the use of a magnet and how you can use it to drag the Rigging Bullet to the hatch opening instead of relying on gravity: th-cam.com/video/6EnHBEEQHYs/w-d-xo.html
Included in this set is Harken Pulleys! LMFAO ya right they now send their shitty Silent Pulleys that break and still charge the same amount for this kit.
What broke on your Stealth Pulleys? Can you send us a picture so we can look into the issue and make sure we can make things right? Email address: support@yakattack.us
Lol, of course he never respond. Troll