Most saw blades today are thin kerf ATB, meaning there is no tooth set, but alternating angle. You would have to set an angle of approximately 5 degrees, sharpen every-other tooth, flip the blade, and sharpen the remaining teeth. Something else, a cheap diamond hand stone is amazingly efficient for touching up carbide. 2-3 strokes make the teeth almost like new.
To że widia się szczerbi jest zła tarcza szlifierska. prawdopodobnie zastosowana ściernica jest do cięcia kamienia lub gresu,ma ona grube ziarna nasypu diamentowego. do ostrzenia należy zastosować tarczę specjalną do ostrzenia widi i wtedy widia się nie wykrusza . Taka tarcza o śr. 125 mm to koszt ok. 40,0 zł.
This setup look too hazardeous, I am sure that better methods are available, including ones that allow a small amount of bevel angle to be maintained on alternate teeth.🤔...
Well done Victor👍 You could mount the blade in a sliding tray. Put a dowel In the centre to hold the blade. Move it in to sharpen. Pull the tray back and move the blade on on the the next tooth and slide it in to sharpen it . Repeat.
Seemed to me to be chipping the edge of most of the teeth, an ingenious solution but could benefit from having a higher grade grinding disk than that used on the video.
Ottima idea ,ma non dai nessuna inclinazione . Forse devi inclinare il tuo piano di lavoro di qualche grado In origine i denti sono molati con una certa angolazione . Bel lavoro ,mi piace ciao Costantino
Völliger Unsinn mit dieser Keramikscheibe ein Hartmetall Sägeblatt zu schärfen. Das Video zeigt dass am Zahn sich Absplitterungen zeigen. Ich rate nur davon ab von so einer Art ein HMBlatt zu schärfen. Diamantscheibe mit Korn 200 und keine zu grobe Fliesenscheibe.
A tile blade on the grinder dont work right is not for metal ..use a blade for metal instead ...just clamp the blade that needs to be sharpened on the table and use the grinder with your hands and doit
Good method for these inexpensive disposable blades, the pivot pin is a simple yet effective gauge, only the face is sharpened with most carbide blades, the tips are factory beveled and won't benefit from additional touch- up anyway.
He does not know what he is doing. Experimenting is fine, but do not tell this is the right way. The teeth are chipping like crazy and he is ruining the blade.
Nigdy nie ostrzyłem tarcz, a na YT szukam pomysłu jak to zrobić. Na Twoim filmie widać (7:18) jak tarcza diamentowa wyszczerbia płytki węglika. Jak tego uniknąć ? Może jest to wina jakości tarczy diamentowej ...
Unfortunately, the showmaker did not pay attention to the inadequacy of the abrasive disc as he fractured during grinding. polished waterway brace, which is a big problem!
Thanks Victor. Your. Idea is better and simple
Good vid. Thank you.
thank you Victor. very well done again.
Most saw blades today are thin kerf ATB, meaning there is no tooth set, but alternating angle. You would have to set an angle of approximately 5 degrees, sharpen every-other tooth, flip the blade, and sharpen the remaining teeth. Something else, a cheap diamond hand stone is amazingly efficient for touching up carbide. 2-3 strokes make the teeth almost like new.
so, it's not good work!!!
На русском у тебя лучше получается 🤣
Die Sägezähne sind doch alle durch die Trennscheibe zerstört worden bzw. man sieht wie beim Schleifen stücke aus dem Widiazahn absplittern.
So siehts aus! Die Blätter kannste hinterher nur wegschmeissen.
It seems to me you can do almost exactly the same thing by simply putting a metal grinding disk on a table saw.
You can, but controlling the speed and ensuring the correct angle is tough.
А мне в видео больше понравилось как болгарка была навешена прямо над проводами удлинителя, прикрученного к торцу стола :)
No se puede ver por las letras estorban pésimo video
Лучше просто субтитры... Бэттер ту мейк...
El letrero no deja ver donde esta el segundo barreno
To że widia się szczerbi jest zła tarcza szlifierska. prawdopodobnie zastosowana ściernica jest do cięcia kamienia lub gresu,ma ona grube ziarna nasypu diamentowego. do ostrzenia należy zastosować tarczę specjalną do ostrzenia widi i wtedy widia się nie wykrusza . Taka tarcza o śr. 125 mm to koszt ok. 40,0 zł.
Русским я лучше владею. Добавьте субтитры.
This setup look too hazardeous, I am sure that better methods are available, including ones that allow a small amount of bevel angle to be maintained on alternate teeth.🤔...
Doesn't work with alternating angles
Phụ đề hàng chử che không thấy gì
Well done Victor👍 You could mount the blade in a sliding tray. Put a dowel In the centre to hold the blade. Move it in to sharpen. Pull the tray back and move the blade on on the the next tooth and slide it in to sharpen it . Repeat.
Seemed to me to be chipping the edge of most of the teeth, an ingenious solution but could benefit from having a higher grade grinding disk than that used on the video.
VOLLMER is more simpler :D
genial compadre, gracias desde buenos aires,
I would expect the grind to not be 90 degrees to the blade face. Every other tooth sharpened at opposite angles to cut smooth and true.
The face IS 90 degrees, the tops are beveled, so this method will work since you are sharpening the faces on each tooth.
@@MJCPeters not...
Ottima idea ,ma non dai nessuna inclinazione . Forse devi inclinare il tuo piano di lavoro di qualche grado In origine i denti sono molati con una certa angolazione . Bel lavoro ,mi piace ciao Costantino
Völliger Unsinn mit dieser Keramikscheibe ein Hartmetall Sägeblatt zu schärfen. Das Video zeigt dass am Zahn sich Absplitterungen zeigen. Ich rate nur davon ab von so einer Art ein HMBlatt zu schärfen. Diamantscheibe mit Korn 200 und keine zu grobe Fliesenscheibe.
Dann wird der Schnitt halt "sägerauh" - das Prinzip ist gut und einfach nachzubauen. ; )
wow.. sometimes the simplest solution works the best.... Very easy and consistent...
Awesome idea! Thanks for sharing this money saving solution !
So simple and accurate.
I'm so glad I saw this! Excellent video! I'm sick of sharpening saw blades by hand with diamond files. I'm going to make this! Top job!🙂👍👍👍
Nice job, thanks.
very good and simple DIY stuff!
Hey there, checked out your vids. Useful things to know. Nice work. New sub here.
mouais boff
A tile blade on the grinder dont work right is not for metal ..use a blade for metal instead ...just clamp the blade that needs to be sharpened on the table and use the grinder with your hands and doit
Good idea / Like
Good method for these inexpensive disposable blades, the pivot pin is a simple yet effective gauge, only the face is sharpened with most carbide blades, the tips are factory beveled and won't benefit from additional touch- up anyway.
VERY KNOWLEDGEBLE VIDEO THANKS VERY MUCH
He does not know what he is doing. Experimenting is fine, but do not tell this is the right way. The teeth are chipping like crazy and he is ruining the blade.
Gracias a ti prologare un poco mas la vida de mi sierra y ahorrare dinero, saludos desde Bolivia 🙂👌
Sencillo, practico y seguro. Gracias.....
What is the name of that sharpening for the circular saw
Simples as mercat would say brill
Nigdy nie ostrzyłem tarcz, a na YT szukam pomysłu jak to zrobić. Na Twoim filmie widać (7:18) jak tarcza diamentowa wyszczerbia płytki węglika. Jak tego uniknąć ? Może jest to wina jakości tarczy diamentowej ...
I think so too
Ese disco rompe los dientes, fijate en el video...
Genial!
Did you set the spiral to 90 degrees
Hi what blade do you use on the grinder
Toutes t'es plaquettes carbure sont éclater,ça doit vibrer ou t'a un grain trop gros !!!
Your predictions have not come true.
THANKS VERY MUCH
thank you ill try it from central america .
ёур инглиш из перфект ;)
донт вори би хеппи
Good idea for sharpening carbide tip blades.
Door lok
This is a bad jig!
plz don't used this method
Why not?
Мутко наконец то делом занялся!
Muy buena idea! Gracias por compartir!!! Saludos desde Argentina.
Загубил диск.
Thanx big time !
das haste sehr gut gemacht!!!!!!
,
very simple and smart
Thanks
Yes,yes, ОБХС ... Выход на международный уровень ...
ОБХСС
ok
Very useful video . Thanks you .
vp jayaweera ..
Unfortunately, the showmaker did not pay attention to the inadequacy of the abrasive disc as he fractured during grinding.
polished waterway brace, which is a big problem!
You're funny
Not good. All teeth need to be the same height/length. Shorter teeth are not doing anything when you're cutting.
But I thought the jig he used ensured all the teeth will grind the same amount off.
Thanks. Now I know how to sharpening my saw blades.
Did you say 50% missing teeth is permissible?
Yes it is.
@@DoitselfInfo says you LOL
bungling
Great video
Пфф, произношение на двоечку)
all the teeth spoiled
Why did you decide so? This saw began to cut better.
You viewed the results; smooth, clean cuts with no smoking- it is good enough!
@@DoitselfInfo I don't think so!
Very good idea ! Thank you very much !!!!!
How did you convert your cordless drill to a plug-in cord because I have one I like for you to tell me how to do it
Thanks...nice..from Roumenia
That is not the way to sharpen a blade. Why go to all this trouble when that small blade is only $10 new?
You must have to much money...the blades here in NZ are $47 for a good quality one. Any money saving is good
Алмазным надфилем можно ещё заточить.80 зубов за 1 час макс.