I originally subbed because of the one-rotor, and I wish that project would've worked out. The Datsun and that Benz definitely have my attention! Keep up the good work!
@@angusmf I mean kinda. It’s buried in my home shop right now. I’m starting to brew up some plans at home to get it running again, but I don’t even have time to get my c4 build done right now. I want it to live as bad as you guys do though
It's just not very common stateside. I don't know all that much about the OM606, but the Cummins 6BT, especially the 24 valve, has a cult following here that would be similar.
There are very few diesel cars here, so this engine and any of it's successors is very uncommon. Unfortunately that makes it expensive to build here too
@@PlayinWithMahWii The Cummins is less than a conventional swap being 1100lbs, half a foot longer than the om606 which is already pretty long. Even a 4bt cummins is an 800lb engine! Om606 rocking some 475lbs which is impressive.
Its not underrated, just unknown and quite unavailable. We didn't get many 606 Turbo cars and only a few NA 606 cars. 603s and 602s are way more common along with the 4 cylinders.
I'm excited for this build. Glad you have content that may be just as cool as the 240 build. For those interested.... I have a pair of bamboo framed boosted shades. Been well over a year. They hold up amazing. And, I'm hard on glasses. I'm hoping to get carbon fiber soon. They were out of stock when I got mine.
I'm gonna tell you right now, if you are planning on twin charging, that turbo is WAY too SMALL!!!!! The primary forced induction has to supply ALL of the airflow you want AT the boost level it will be running on its' OWN...so unless you want to make 350 whp, that turbo is TOO SMALL...edit: If you run upwards of 42-45 psi, you might be able to get the airflow for like 650 hp...that was going off of an s475 map, I couldn't find a direct map for that compressor based on what you stated. The supercharger is going to be running about a 1.8 CR, and if you run a 2.2 on your turbo, you'll get about 43 psi of boost. So just make sure that your turbo is capable of providing the airflow you want at between 2.0-2.2 unless you want higher boost. Also keep in mind that the m90 is REALLY inefficient, so if you can, put an A2W intercooler on the S/C or your air charge temps will be through the roof.
I don’t disagree. This turbocharger was originally purchased with the intent of using it solo. It’s a BW 7670 EFR turbocharger, bought as a super core, with a 1.0 a/r T3 twin scroll exhaust housing. The turbo can supply enough air at a pr for twin charging to hit around 400-450hp not accounting for losses from the supercharger, so more than likely the turbo will be changing before the build is done. I may just end up slapping it on the stock NA engine and just send it with a 400hp no fucks given thing
@@jamescrapeticio2771 Kewl beans, at least you know. I've seen lots of people go to huge expense doing twin charge builds, and then get disappointed and consternated when the build doesn't make the power they want. A lot of the time, they're afraid to use a big enough turbo because they're afraid of lag, but they don't seem to realize that one, you've already got the supercharger adding air and fuel so it's got more exhaust to spool the turbo faster and two, the turbo doesn't have to spool to 45 psi to give you 45 psi. I mean it has to spool to 15 psi to give you 45 and like 25 to give you 60. edit: Just be careful with those super high boost levels that your secondary forced induction has enough flow, that's the most difficult calculation although still not that difficult. The m90 is good for about 350 hp at a relatively safe spin rate so imagine 30-35 lbs a minute. so at a 1.8 C/R you're looking at a theoretical max of 63 lbs a minute but your efficiency will drop. So you can probably get 600 wheel without upgrading the S/C. But your torque curve will be INSANE. A properly setup twin charge setup at 600 wheel will outperform the same engine with a single FI source that runs at 850.
@@BrockJaden yea I’m excited to try this out. I’m thinking that I’ll pick up a s475 in t4 turbine if I can but I think I can make t6 work if need be. That should have no issues chasing down the mass flow numbers I need, and the m90 will do it’s job fine enough. In a perfect world I’d run a efr 8474 and a gt500 TVS supercharger to get a much better flowing more modern version of what I’ll cobble together myself lol
@@jamescrapeticio2771 Yeah and the good thing is that if you get the inclination, turning up the boost shouldn't be a problem on a diesel... There are triple compounded turbos running 150 psi on some diesels.
@@jamescrapeticio2771 Yeah for that amount of boost you dont need to twin charge it. Just put a good single turbo on and enjoy. You are headed for a world of pain with all that needless complexity. Getting it built will be the easy part and then you will be starting a totally new project of making it function properly and modifying it.
I'm not sure how long I've subscribed to this channel but I'll tell you this much is that I know you guys are out here trying to do your thing and some of your ideas have been a little unconventional and I've loved that too. I will keep watching as long as you guys keep posting! On a side note I have tried to buy some of the boosted shades but some of them seem to be out of stock. That's not a dig at you guys, just wanted to tell you that I also wanted to support you in that way and I will keep checking back on the website
I used to do pharmacy deliveries in a Volvo 240 wagon with a 5 speed. It still drove like a small truck, and I still loved it. Hope you haul some crap in your merc-wagon!
@@welcome2myworld1.o89 Brand loyalty and more specifically part loyalty to one company should go directly out the window on a build like this. Especially on engine families with less than "complete" aftermarket support. Its no more or less botched, just how it goes.
The diy wide body is more for bigger tires than aesthetics. W124s have tiny inner wheel space and I don’t want the car to be a massive tire burner, I want it to be fast and actually drive like some kind of aggressive e300 EVO AMG Black thing thing
@@jamescrapeticio2771 oh I see exactly what you’re talking about As I said, very good looking and I respect all choices made by a car lover so keep up and I can’t wait to see the final result
Once you guys get the twin charged system dialed in you're gonna have so much fun with it, boosted diesel torque is unreal, it just keeps pulling and pulling!
Damm guys great content really!! Im so excited to watch both diesel builds!!! i hope that videos! i saw a guy who is from united kindon that made something similar with a om 606 twin charged build but in a vw golf
I have a 1996 c220 I've wanted to diesel swap ever since you guys started to play with the om606. Now you made it more interesting with the c230 kompressor 6 speed. Can't wait to see how these projects turn out.
This is insane. I have a tendency to run away with my ideas, and having just picked up my first om606 last weekend, I’m so excited to see you guys take this to the max. I feel like you’re gonna need more turbine but either way this is gonna make some violent sounds.
Lol, I didn't see when you uploaded this vid. Suddenly today I started wondering if one could twincharge a diesel and - voila! :D I love your work guys!
The title caught my eye to be honest. The 2jz are damn good engines from what ive seen and you can run a lot of power through em before you really have to do anything with the block or so ive heard. Hope this Diesel set up works for you guys.
I don’t like much sedans at all, imo if a car had a coupe or wagon option it they always look better, but to each their own, tbh it’s mostly just because If I’m going to be hitting my head on a b pillar I want to have the extra storage space. Lol
@ Team Boosted Do you sell Boosted Shades that will clip onto eyeglasses? It would be great if you could somehow make them where the clips are clipping at the ends of the lenses rather than the old style clips that would clip onto the center of eyeglasses that always ended up scratching the eyeglasses.
Diesel pump UK are all out of 606s. I'm trying to organise one for a japan built 280zx build but no luck. Might end up putting a turbo barra in it instead
banks power had a twin boosted setup where the turbo fed the supercharger, it seems that it would be better to feed the turbo from the supercharger? or maybe get a procharger feeding the turbo instead?
I originally subbed because of the one-rotor, and I wish that project would've worked out. The Datsun and that Benz definitely have my attention! Keep up the good work!
Did they give up completely on the one rotor?
Same here! Love the content. Still waiting on the Manual transmission M120 mustang!
@@povlrueger3898 shit i hope not. They need to getbthe Vargas brother's in there to help em out
Yeah, what actually happened? Did they just say screw it one day and push it behind the shop?
@@angusmf I mean kinda. It’s buried in my home shop right now. I’m starting to brew up some plans at home to get it running again, but I don’t even have time to get my c4 build done right now. I want it to live as bad as you guys do though
The om606 seems to be underrated in the US, here in Scandinavia its one of the most popular old diesels to tune. Love the builds you guys are doing!
It's just not very common stateside. I don't know all that much about the OM606, but the Cummins 6BT, especially the 24 valve, has a cult following here that would be similar.
There are very few diesel cars here, so this engine and any of it's successors is very uncommon. Unfortunately that makes it expensive to build here too
@@PlayinWithMahWii The Cummins is less than a conventional swap being 1100lbs, half a foot longer than the om606 which is already pretty long. Even a 4bt cummins is an 800lb engine! Om606 rocking some 475lbs which is impressive.
Its not underrated, just unknown and quite unavailable. We didn't get many 606 Turbo cars and only a few NA 606 cars. 603s and 602s are way more common along with the 4 cylinders.
Is it really surprising that an engine that was never mass produced here isn't that well known or popular? The 606 is in the same boat as the Barra
Haha love the Runescape song remix on the new project reveal!
dude thats what i thought was going on
i love it too
whats the song name?
I want to see more of this engine and build
Never got an update on the dry sump omo606 build
I'm excited for this build. Glad you have content that may be just as cool as the 240 build. For those interested.... I have a pair of bamboo framed boosted shades. Been well over a year. They hold up amazing. And, I'm hard on glasses. I'm hoping to get carbon fiber soon. They were out of stock when I got mine.
Finally an America w124. the reliably capable 800+hp mo606. thank you guys
lookin really lovely. cant wait to keep watching the build. dream build.
Love the runescape music thought I was watching a panic07 video for a sec then tripped me out a bit 😆
Please give more detailed content on this engine build
MY BOYS WITH OSRS MUSIC
I'm gonna tell you right now, if you are planning on twin charging, that turbo is WAY too SMALL!!!!!
The primary forced induction has to supply ALL of the airflow you want AT the boost level it will be running on its' OWN...so unless you want to make 350 whp, that turbo is TOO SMALL...edit: If you run upwards of 42-45 psi, you might be able to get the airflow for like 650 hp...that was going off of an s475 map, I couldn't find a direct map for that compressor based on what you stated. The supercharger is going to be running about a 1.8 CR, and if you run a 2.2 on your turbo, you'll get about 43 psi of boost. So just make sure that your turbo is capable of providing the airflow you want at between 2.0-2.2 unless you want higher boost.
Also keep in mind that the m90 is REALLY inefficient, so if you can, put an A2W intercooler on the S/C or your air charge temps will be through the roof.
I don’t disagree. This turbocharger was originally purchased with the intent of using it solo. It’s a BW 7670 EFR turbocharger, bought as a super core, with a 1.0 a/r T3 twin scroll exhaust housing. The turbo can supply enough air at a pr for twin charging to hit around 400-450hp not accounting for losses from the supercharger, so more than likely the turbo will be changing before the build is done. I may just end up slapping it on the stock NA engine and just send it with a 400hp no fucks given thing
@@jamescrapeticio2771 Kewl beans, at least you know. I've seen lots of people go to huge expense doing twin charge builds, and then get disappointed and consternated when the build doesn't make the power they want.
A lot of the time, they're afraid to use a big enough turbo because they're afraid of lag, but they don't seem to realize that one, you've already got the supercharger adding air and fuel so it's got more exhaust to spool the turbo faster and two, the turbo doesn't have to spool to 45 psi to give you 45 psi. I mean it has to spool to 15 psi to give you 45 and like 25 to give you 60.
edit: Just be careful with those super high boost levels that your secondary forced induction has enough flow, that's the most difficult calculation although still not that difficult.
The m90 is good for about 350 hp at a relatively safe spin rate so imagine 30-35 lbs a minute. so at a 1.8 C/R you're looking at a theoretical max of 63 lbs a minute but your efficiency will drop.
So you can probably get 600 wheel without upgrading the S/C. But your torque curve will be INSANE. A properly setup twin charge setup at 600 wheel will outperform the same engine with a single FI source that runs at 850.
@@BrockJaden yea I’m excited to try this out. I’m thinking that I’ll pick up a s475 in t4 turbine if I can but I think I can make t6 work if need be. That should have no issues chasing down the mass flow numbers I need, and the m90 will do it’s job fine enough. In a perfect world I’d run a efr 8474 and a gt500 TVS supercharger to get a much better flowing more modern version of what I’ll cobble together myself lol
@@jamescrapeticio2771 Yeah and the good thing is that if you get the inclination, turning up the boost shouldn't be a problem on a diesel... There are triple compounded turbos running 150 psi on some diesels.
@@jamescrapeticio2771 Yeah for that amount of boost you dont need to twin charge it. Just put a good single turbo on and enjoy. You are headed for a world of pain with all that needless complexity. Getting it built will be the easy part and then you will be starting a totally new project of making it function properly and modifying it.
No way you used runescape music lol I love this channel even more
This is gonna be the best build so far!! The sedan and the estate👌🏻 I'm watching closely as I have an om606 w124 estate build in the garage💪🏻
If you use hvo diesel it should run smoother and rev higher
you guys were literally in my back yard on those first pulls in the video!
Love the build. Reminds me of old school DTM, and I love DTM
Y’all build the way I do work with what you have make it work. I love how different all the builds are to.
I'm not sure how long I've subscribed to this channel but I'll tell you this much is that I know you guys are out here trying to do your thing and some of your ideas have been a little unconventional and I've loved that too. I will keep watching as long as you guys keep posting! On a side note I have tried to buy some of the boosted shades but some of them seem to be out of stock. That's not a dig at you guys, just wanted to tell you that I also wanted to support you in that way and I will keep checking back on the website
huge fan of the W124 - also HUGE fan of the twincharging. Cant wait to see - always wanted a twin-charged car ever since i saw the Delta S4
Def gonna need all the wagon content you guys can do. Loving the 90s DTM vibes
I used to do pharmacy deliveries in a Volvo 240 wagon with a 5 speed. It still drove like a small truck, and I still loved it. Hope you haul some crap in your merc-wagon!
I love how this motor is made from so many farts from other manufacturers😅
Hehe farts
Could be a good thing.. and can be a major bad thing
@@welcome2myworld1.o89 Brand loyalty and more specifically part loyalty to one company should go directly out the window on a build like this. Especially on engine families with less than "complete" aftermarket support. Its no more or less botched, just how it goes.
@@madmod also brand loyalty makes boring builds
Unique farts, the more unique farts the better the gas mileage
Every thing you did in the video to the car seams like it’s going to be really fast and dope af
Looks cool, I would definitely keep a more stock appearance with some “amg” parts but the one you showed is also very good looking
The diy wide body is more for bigger tires than aesthetics. W124s have tiny inner wheel space and I don’t want the car to be a massive tire burner, I want it to be fast and actually drive like some kind of aggressive e300 EVO AMG Black thing thing
@@jamescrapeticio2771 oh I see exactly what you’re talking about
As I said, very good looking and I respect all choices made by a car lover so keep up and I can’t wait to see the final result
love the update on the builds and i think its pretty cool that your shops builds are super original.
Shout out to these guys for making some of the best om606 content on youtube.
These cars just keep getting crazier!
I love it
Teamboosted, just trying to kill an 18 year old one vehicle at a time.
amen!
I grew up in the early 2000’s my first car was a self built 7mgte 87 turbo targa Supra that was notorious around Philly 05-07 lol
Your builds keep on getting crazier I love it
That w124 is going to be an absolute weapon. The fenders and bumper look really great
Can’t wait to see what the intake looks like on the OM606? Just found this channel. Sweet !!!
Once you guys get the twin charged system dialed in you're gonna have so much fun with it, boosted diesel torque is unreal, it just keeps pulling and pulling!
Damm guys great content really!! Im so excited to watch both diesel builds!!! i hope that videos! i saw a guy who is from united kindon that made something similar with a om 606 twin charged build but in a vw golf
I have a 1996 c220 I've wanted to diesel swap ever since you guys started to play with the om606. Now you made it more interesting with the c230 kompressor 6 speed. Can't wait to see how these projects turn out.
Team Boosted: We have another OM606!
Mercedes W124: My body is ready!
This is insane. I have a tendency to run away with my ideas, and having just picked up my first om606 last weekend, I’m so excited to see you guys take this to the max. I feel like you’re gonna need more turbine but either way this is gonna make some violent sounds.
I like the dedication to the diesel cause!
I’m so excited for the development of this build!
In my OM606 are DN0SD265 Nozzels with 150 Bar. These provide more Fuel. Good Luck with your Projects.
I love it, its got very early nineties DTM vibes. Gonna be a rocket!
Plus the wagon is sick as hell
This build looks insane! Can't wait to hear this twin charged system!
What happened with this build? Any updates?
Lol, I didn't see when you uploaded this vid. Suddenly today I started wondering if one could twincharge a diesel and - voila! :D I love your work guys!
oh man I can't wait to see that twin turbo death trap build. absolute madmen
Like all of the ideas going on in the shop. Awesome!
So glad you've decided to do a Porsche engine in the 911 rather than the LS you were originally planning. Looking forward to that build now.
Loving the wagon!
Pretty pumped for the Merc content! There is someone in Norway that has a super-turbo OM606 in a Cherokee that is ridiculously fast! 👌🏼
The title caught my eye to be honest. The 2jz are damn good engines from what ive seen and you can run a lot of power through em before you really have to do anything with the block or so ive heard. Hope this Diesel set up works for you guys.
It's not a real 2JZ, it's the OM606, just KNOWN as the 2JZ of diesel.
hahah loving the osrs music again!
Big plans like always... Don't spread yourselves too thin though. I think we all wanna see the Datsun back ASAP.
I’m liking all the Mercedes and W124 content hell yeah, keep it up!
8:38 mark, “biggafied” most certainly the correct technical term.
Beam Toosted. It’s fire as always!!!
Ok.. Ok... I'm a cummins truck guy... NOW IM SHOPPING FOR FOR A 124 AND LOVING THE TWIN CHARGE IDEA! following closely for ideas/lessons learned!
you guys have a massive set up. great way to sup up the RPM. taking ideas for my nissan sunny n13 diesel
W124+THAT ENGINE= DEATH, but also alot of fun. Have a great day sir :D
Absolutely nutty bro I love it
Finally getting Patreon! I'm in as soon as it's up!
Fantastic work guys
Twincharged FOR THE WIN
Dude that Benz is sickk
I don't know much about diesels, but you guys have done pretty interesting projects. Looking forward to where these things go😁
That's awesome! I want to use that supercharger on my 2jz. Love the channel, keep it up
A DTM inspired w124 Turbo Diesel???? You guys deserve more viewers
Merc Turbo Diesel turned up to Infinity and beyond...I'm ready for that one.
I'm really excited about this project not enough channels modify old Mercs totally unappreciated cars for tuning. Top work as ever Team boosted 👍👍👍
Love the w124 in all ways. Altough the s124 (wagon) is not as much in my taste. Will be interesting to follow all projects either way.
I'm a sedan man too.
I don’t like much sedans at all, imo if a car had a coupe or wagon option it they always look better, but to each their own, tbh it’s mostly just because If I’m going to be hitting my head on a b pillar I want to have the extra storage space. Lol
@@samjohnson7325 I have 2 940 volvos. Built the wagon because it was clean but ended up selling it I never got used to it.
This guys are awesome...
The w124 project is super awsome! Please show us more of it!
Let’s go boys !!!!!
So many activities boys y’all better get the go pro’s pippin film it all and we will love y’all for it lol
And what about the exhaust manifold??🙏🏼
My opinion is it's an awesome build like everything you guys do!
@
Team Boosted
Do you sell Boosted Shades that will clip onto eyeglasses? It would be great if you could somehow make them where the clips are clipping at the ends of the lenses rather than the old style clips that would clip onto the center of eyeglasses that always ended up scratching the eyeglasses.
So many sick projects! As for the über badass W124 project, I expect it to be pretty damn insane.
Team Boosted y'all rock! Love the channel and content keep up the great work! I'm here for the algorithm! Peace
killing the diesel game ! ! !
Where do you find the om606 engines? I'm having a hard time finding any....
Find a rotted mercedes w210 e300 turbodiesel
The holes have been ‘Imbigified’😅
First thought was that Simpson episode where Lisa gets "debigufied" or some shit by the little people she accidentally creates.
friggin love the E class !!! great content as usual
Got the wagon love!
What upgrades will be done to the 240z suspension are the airbags gonna stay?
haven't seen a killer high power euro benz in a bit... it will be great. What color, murdered out seems fitting, but I don't expect the expected.
Can not wait for the sounds this boxy duel charged beast will make!
He said: let’s go from right to left like reading a manga” I see u a man of culture 💯
Moo Poweeeeer Beebeehhhh
Yessir
Hell yeah this is gonna be rad
Merc looks sick, very 90s DTM looking, which is awesomeness 🤙🏻. I have the same Ferrari flag in my garage 😁
That m90 is really only good for about 400hp really maxed. It's going to be a restriction to push more air through it.
And they are mega heat makers at high power too. Maybe look at the m112(? I think)off a gt500 mustang.
Diesel pump UK are all out of 606s. I'm trying to organise one for a japan built 280zx build but no luck. Might end up putting a turbo barra in it instead
Love your work guys keep it up
Can’t wait to see this completed and ripping down the road.
banks power had a twin boosted setup where the turbo fed the supercharger, it seems that it would be better to feed the turbo from the supercharger? or maybe get a procharger feeding the turbo instead?
Love the older Mercedes-Benz w124’s
Broooo nastiest diesel in the gamw
*game
Siiiiiick all yalls builds are awesome and unique keep em coming love it 😀
Are you guys familiar with Team Lovetap and their work with M104s. The blocks and oil pan/girdle are fairly similar.
You guys seem to really love this engine and I can see why!
Should be pretty crazy can’t wait 👍👍👍👍
Just got some heatwaves but .grabbing a pair of the boosted shades next
if the w124 is anything like the datsun build theni ts going to be sick! such a cool car as well