As you stated, the 2nd gen S&B particle separators have a sensor that attaches around a coil pack wire that speeds up or slows down the scavenge fans according to engine RPM 's. Mine seems to work well, was relatively easy to install & it looks good on my 21 Can Am X3 XRC turbo RR.
@@orion000 It was last time I used my Can Am maverick X3 but I've since sold that & gone over to a Can Am Outlander 650 Max 6x6. It did seperate out alot of dust & particles that used to make their way onto the airfilter element. They do work.
Does it make a huge difference if it's mounted high or low. I've seen people mount it on the roof and behind the cross bar in the back? Just curious. I've had people tell me it doesn't make a big difference. I find that hard to believe. Thoughts?
I just installed mine. Its about as loud as your air conditioner in your car/truck is when its on full blast. You can remedy this by putting it on a switch so you can turrn it off if you want. Mine is installed in a 4 seater so not sure I can hear it at idle. Maybe the occupants in the back can. I cant hear mine pick up when I rev the gas either. One thing I noticed when I was installing it, is it looks like there us only exhaust on the center fans. It looks as if the fans to the left and right might be dummy fans? I didnt see anything stopping dust coming through those fans that would prevent it from going right to your air filter. Maybe theres some black magic. Im going to put a prefilter between the filter and the tube to see if anything gets picked up there.
Will the new version fit on the same brackets the old one attached to?...being able to just replace the unit without replacing the mounting clamps would be a huge advantage..
It could if you have other accessories that attach to the same bar you're using for the particle separator. But you can mount this in a couple different positions on most machines to work with other accessories.
How would I install the particle separator on a x3 with a rear window ? Can it mount on the top bar rising over the roof? And does it also keep the clutch air clean? Thanks
It just helps keep your air filter clean and nothing more. A clean air filter will prevent power loss, especially on turbo machines. That's it as far as performance, no other modifications needed. These work really well, but you should still check your air filter periodically and change when needed. -Charles
We just installed on a 2021 razor Xp 1000. We mounted at about the roof line however it has a high pitched whining which is making me crazy. We have a front and back windshield. It seems to be most noisy when running at 5 to 20 mph. Any ideas on getting rid of that high pitched whine?
I have a Polaris 900S that I have installed Ryfab front and rear windows, rear rack and trunk box. Any suggestions on how I would get the clean air tube to the air box?
You don't need to worry about covering the particle separator when washing your machine or driving in rain. With rain being heavier than air, these filters will separate water particles like it does with dust. There is also a drain before the stock intake that allows water to exit before hitting your stock airbox.
Yes, these particle separators come with mounting that can be used on the upper or lower roll bars so they can work with windshields, rear windows, spare tire racks, etc. It can be mounted slightly above the roofline if there is a front or rear windshield.
Yes, you just may have to mount it in a different location. This kit comes with 2 different sized clamps for the X3 so this can be mounted on the larger bar behind the seats or on the cage. S&B has a good video showing this mounted in the lower location to give you a better idea. You can check out that video here: th-cam.com/video/w8kVKtqle58/w-d-xo.html
Depending on which rear window you have, you could mount the particle separator to the top roll cage bar and have it sit above the roof line. The clamps are pretty low profile so not much room is needed.
The kit for the X3 comes with 2 different sized clamps so you can mount this particle separator to to the large bar behind the seat or the small bar for the roll bar on the top of the cage.
Yes, these are available for your X3. Just be sure to enter the year, make and model on the product page to get the correct one. You can click the first link in the description of this video or the link below. www.rockymountainatvmc.com/parts/s%26b-filters-particle-separator-2-p
That's just waste of money. "After 50 hrs filter is still clean" 😂😂😂 When I'm riding for four days weekend Trip every morning I clean the filter, blow off the belt and check oil... Don't be Soo lazy people. Clean your shit.
As you stated, the 2nd gen S&B particle separators have a sensor that attaches around a coil pack wire that speeds up or slows down the scavenge fans according to engine RPM 's. Mine seems to work well, was relatively easy to install & it looks good on my 21 Can Am X3 XRC turbo RR.
That's awesome! Glad its working well for you. Be sure to leave a review on our website!
Is it still running strong?
@@orion000 It was last time I used my Can Am maverick X3 but I've since sold that & gone over to a Can Am Outlander 650 Max 6x6. It did seperate out alot of dust & particles that used to make their way onto the airfilter element. They do work.
@@dustyfarmer oh snap how is that 6x6
@@orion000 Sweet, I'd never own a four wheeled ATV again, 6x6 is where its at.
I have one of these on my Kawasaki KRX 1000eS and it works awesome!
Could you post a few pictures. I have a krx and I'm interested in one.
Does it make a huge difference if it's mounted high or low. I've seen people mount it on the roof and behind the cross bar in the back? Just curious. I've had people tell me it doesn't make a big difference. I find that hard to believe. Thoughts?
I just installed mine. Its about as loud as your air conditioner in your car/truck is when its on full blast. You can remedy this by putting it on a switch so you can turrn it off if you want. Mine is installed in a 4 seater so not sure I can hear it at idle. Maybe the occupants in the back can. I cant hear mine pick up when I rev the gas either. One thing I noticed when I was installing it, is it looks like there us only exhaust on the center fans. It looks as if the fans to the left and right might be dummy fans? I didnt see anything stopping dust coming through those fans that would prevent it from going right to your air filter. Maybe theres some black magic. Im going to put a prefilter between the filter and the tube to see if anything gets picked up there.
Will the new version fit on the same brackets the old one attached to?...being able to just replace the unit without replacing the mounting clamps would be a huge advantage..
Does this prevent any accessories from being attached?
It could if you have other accessories that attach to the same bar you're using for the particle separator. But you can mount this in a couple different positions on most machines to work with other accessories.
How would I install the particle separator on a x3 with a rear window ? Can it mount on the top bar rising over the roof? And does it also keep the clutch air clean? Thanks
A year and no reply I need this as well before I buy the window and particle separator
Is there a way to bypass the ignition sensor. Just to keep it on high at all times?
I’m looking for a set up for a 2021 Polaris ranger 570 midsize
Does adding this give your machine any extra horsepower or does it affect with the fuel and air ratio of the engine ?
It just helps keep your air filter clean and nothing more. A clean air filter will prevent power loss, especially on turbo machines. That's it as far as performance, no other modifications needed. These work really well, but you should still check your air filter periodically and change when needed. -Charles
We just installed on a 2021 razor Xp 1000. We mounted at about the roof line however it has a high pitched whining which is making me crazy. We have a front and back windshield. It seems to be most noisy when running at 5 to 20 mph. Any ideas on getting rid of that high pitched whine?
I have a Polaris 900S that I have installed Ryfab front and rear windows, rear rack and trunk box. Any suggestions on how I would get the clean air tube to the air box?
mount it on the roof.
Does this need to be covered when cleaning/powerwashing my machine ? How waterproof/resistant are they ?
You don't need to worry about covering the particle separator when washing your machine or driving in rain. With rain being heavier than air, these filters will separate water particles like it does with dust. There is also a drain before the stock intake that allows water to exit before hitting your stock airbox.
@@rmatvmc appreciate the insight just wanted to be sure before I ordered one. I'm in the desert so I feel this thing is a must
Will this still be affective if you have a front windshield?
Yes, these particle separators come with mounting that can be used on the upper or lower roll bars so they can work with windshields, rear windows, spare tire racks, etc. It can be mounted slightly above the roofline if there is a front or rear windshield.
How bout a regular suv
This will not work for an suv.
I own a polaris ranger 900xp 2017, this should fit right on the upper bar right?? I don’t see an option for my ranger on your sight.
www.rockymountainatvmc.com/parts/s%26b-filters-particle-separator-p
Here is a link to the product page with a 2017 Ranger XP900 selected.
Can you have a can am rear windscreen with this?
Yes, you just may have to mount it in a different location. This kit comes with 2 different sized clamps for the X3 so this can be mounted on the larger bar behind the seats or on the cage. S&B has a good video showing this mounted in the lower location to give you a better idea. You can check out that video here: th-cam.com/video/w8kVKtqle58/w-d-xo.html
I have a 2023 KRX 1000 with a rear window, Where do I mount it?
Depending on which rear window you have, you could mount the particle separator to the top roll cage bar and have it sit above the roof line. The clamps are pretty low profile so not much room is needed.
I have a can am max . Is this separator compatible with my rear window?
The kit for the X3 comes with 2 different sized clamps so you can mount this particle separator to to the large bar behind the seat or the small bar for the roll bar on the top of the cage.
Can I use the roll cage version on my Polaris pro xp with the Polaris spare tire carrier is there figment issue’s
you could swing the bracket up and mount it above your roof they have a 3 inch extension you can buy extra.
Do you know if this will separate water from the air? Wondering if this is good for a tracked sxs where snow can get in there.
This is designed to separate dust and dirt particles. They don't say anything about water. This is something you would need to reach out to S&B about.
On their site q&a it can handle some water you of course can't flood the thing but it will handle some water.
Can you mount this above the roof?
Yes you can!
Will it work with can am x3 xmr
Yes, these are available for your X3. Just be sure to enter the year, make and model on the product page to get the correct one. You can click the first link in the description of this video or the link below.
www.rockymountainatvmc.com/parts/s%26b-filters-particle-separator-2-p
That's just waste of money. "After 50 hrs filter is still clean" 😂😂😂
When I'm riding for four days weekend Trip every morning I clean the filter, blow off the belt and check oil... Don't be Soo lazy people. Clean your shit.
Whatever works for you! But you wouldn't need to clean your filter everyday if you had this 😎