This guide is the most accurate one that i found. Thanks to that and to the dortania guide i hackintoshed a MSI GL75 10th gen I7, 32gb of ram and it worked perfectly almost first time (except for wifi and bluetooth)
Thank you for this video, i already did a build before with AMD. Switched now too Intel, was quite a hassel with Raptor Lake (13th Gen, there is no official guide). But nice too have a video like this and go trough everything along side too checkup. Got everything working, even P-Cores and E-Cores so it has fully support till 5.4 GHz :) MacOS: Ventura Intel i7 13700k AMD 6600
Gotta tell ya this is by far the most in depth and accurate guide I’ve come across.I have a system similar to yours. I7 4790k but it’s in an hp g1 800 sff paired with an lp rx550 4gb. I patched the Gpu and with the t919 everything works flawlessly. Only issue I’m having is I cant use the hdmi port on the Gpu for dual monitor support. I added framebuffer patches for the connector and went from no signal at to a color flash followed by blank screen to no signal every 10 seconds. I dont quite understand how to patch the busid but I’m guessing that’s what I need to do since I’ve tried everything else. Funny thing is I can use an hdmi cable if I plug it into a dp to hdmi adapter via the dp port. Smbios I use is iMac18,3. Could that be my issue?
I can dig into it more . I thought 18,3 is a good smbios. You can try a different smbios. Also is your bios settings correct? Is CSM disabled? I got a black screen with CSM enabled and disabling it seemed to solve it. Other than that it might be other config settings we need to look at.
Your guide was truly very useful. I cant thank you enough!!! And I managed to setup a Intel B660M and i3 12100 based system with it. But I had to struggle & search around the internet to get the installer run properly, but in the end the it was very well worth it and your guide IMMENSELY helped me out understanding the all the details. I have following request for you: Please make a video guide on how to maintain and keep the hackintosh stable. Please make a video guide on dual-booting with existing windows installation. And lastly if possible please make a guide for 12th and 13th Gen Intel platforms opencore and plist setup. The reason I'm requesting is because NONE of the youtube videos goes this deep and comprehensive like your videos. (I watched close to 80-90 videos and almost all of them were based on pre-baked EFIs and installation ISOs ). Kind and best Regards!!!
1) keep hackintosh stable - OpenCore is very stable once you configure it right. 2) dual bootong - great idea for a video, 3) - would love to if I had the funds to purchase this equipment... Thanks again
You are a true Technologist my brother 💯 Thank you for making this video. 🙏 Watched it fully last night along side your 26 min version and it really helped me to not only finally understand the process but also how to try it now myself without a configurator. 💪 Please keep em coming!! 🔥 LIKED & SUBBED
Great video and info - needed a bit of hand holding as my laptop requires a lot of Kexts and arguments in the config.plist and it's a bit overwhelming - great job!
Thank you for going over every? most? steps in building the USB installer. One difference I saw with mine is that.. during the first reboot, instead of text based loader screen,,, I had GUI icons? other than that. all worked. Also, during the setup screen, I didn't get choose language but straight to country selection. Also, my USB Applekeyboard did not get recognized. odd.
You probably configured the gui picker you can turn it off though. Also you can set your language in the config. Also you need to map your usb or use the default kexts
Would be a lot of expense for you but any chance of doing a Ryzentosh in depth guide of the newer way of creating R/Hackintosh I keep getting things wrong and it’s very frustrating 🙏🏻🙏🏻🙏🏻😉😉😉 still got a stable Catalina build from way back when, in the Opencore 0.5.9 Days 🤣🤣🤣
🎯 Key Takeaways for quick navigation: 00:00 🖥️ *The video is about installing macOS Ventura on a Haswell PC using the Windows 10 operating system.* 01:20 📦 *You'll need specific hardware components like an AMD GPU (Nvidia not supported), SSD storage, an Intel chipset for Ethernet, and a compatible Wi-Fi/Bluetooth card.* 02:59 💻 *You can choose between Windows 10, Mac OS, or Linux as your primary operating system for the installation process.* 03:26 ⚙️ *Make sure to update your BIOS to the latest version before proceeding.* 06:01 📀 *Creating a bootable USB drive using Rufus is recommended for the installation process.* 13:52 🐧 *If generating ACPI SSDTs, using a Linux installation on a separate USB drive is suggested for efficiency.* 16:34 📂 *You need to gather various files, including drivers and EFI files, and configure your config.plist file.* 26:56 🍎 *Selecting the correct SMBIOS (system profile) for your hardware is crucial for a successful installation.* 30:53 ⚙️ *Configure your computer's BIOS settings as recommended in the Dortania guide for the installation process.* 31:36 ⚙️ *Configure BIOS settings for Hackintosh by going to the Advanced section and ensuring proper settings, such as SATA configuration (AHCI), disabling VTD, and adjusting Graphics configuration for dedicated graphics cards.* 36:29 💻 *If you encounter a black screen during installation, consider downloading and installing "WhateverGreen" to address graphics-related issues.* 37:35 📝 *Disabling Compatibility Support Module (CSM) in the BIOS may be necessary to ensure a successful Hackintosh installation.* 38:27 🌐 *After installing macOS Ventura, use a tool like "Mount EFI" to access the EFI partition and copy necessary files from your USB drive to your hard disk's EFI partition for proper booting.* 41:05 📦 *To configure USB ports, use "USBMap" to identify and map the USB ports on your computer. Create a USB map, copy it to the EFI partition, and update your config.plist for USB configuration.* 44:13 🚀 *Transition from debug mode to release mode by downloading release versions of necessary OpenCore files, drivers, and kexts. Replace debug versions with release versions for improved performance.* 48:22 🖥️ *Customize the OpenCore graphical user interface (GUI) by configuring options like "picker mode," "picker attributes," and "picker variant" in your config.plist.* 50:27 🔊 *Optionally, enable the Mac boot chime in OpenCore settings and adjust boot arguments to remove verbose mode for a smoother Hackintosh experience.* Made with HARPA AI
Hey brother great video, just one question after successfully installing OS can I boot into my windows 10 back, like this process is a dualboot or will it override my windows?
Hello! Thanks a lot for your guide, it was extremely helpful) Did you able to make sleep working? In my case i trying many different methods and it won't work((
@@Studio3BRocks I tried many different methods in the internet but nothing worked:( I guess we need some DSDT patches to start it work properly, cuz previously in the Mac OS Mojave with clover it worked great
@@MsVladmen yes unfortunate for this older model pc (haswell). If i were to start over I'd go the OpenCore buyers guide and get all compatible components.
Hi, you can get the opencore-**.txt file from your most recent boot attempt off your EFI partition (assuming you have debug turned on). You can take a look at where it is stalling and go from there. Let me know if I can help more.
I followed your guide, it was very detailed! I'm having an issue where no drives show up on the MacOS install screen. Even when I click show all devices, I only see the installer. I made sure to set my BIOS settings according to the Dortania guide (i.e. AHCI mode, etc.). Do you know why this could be? My machine has a 10700k and my motherboard is an MSI MPG B460i.
The video is entitled "Hackintosh Ventura - In-Depth Guide (Windows Method)" Now out of nowhere we have Ubuntu configuration added to the mix. Time to look for a better Hackintosh video!
Hey man, i followed this tutorial and installed ventura, i needed that for xcode and now i see that ventura doesn't support it and i really don't want to spend another 10 hours fixing issues, can i upgrade to sonoma directly from software update? Normally like on MacBooks or do i need to redo it all over again:,) thank you for the great tutorial anyways:)
@@Studio3BRocks hey man justa quick one at 48:23 i did these steps and didnot touch the boot chime, before doing all that it was showing digital out under the sounds tab which is gone now, it only shows my microphone that is connected over USB, i did undo of all the stuff that i had done, what should i do in this case?
After many tries, I successfully got up to the USB Mapping part (last step before removing verbose and debugging) with my HP ProDesk 600 G4 and after a long reboot I have no keyboard and mouse or any USB ports. Not sure what I did wrong. Looks like I am starting over.... again :(
24:18 I'm wondering if you even need to define device-id as it seems your CPU has HD 4600 instead of HD 4400 (that latter needs to be faked as HD 4600?) Same with PciRoot(0x0)/Pci(0x1b,0x0) section - if you are not going to use it, then I think it is good to remove it.
I keep getting the "In Memory Panic Stackshot Succeeded" error. And other times it's giving me a ""Kextlog: kernelmanagerd is not active" message. I can't get past the first wall of text screen. Please help
Id have to look at your EFI. Make sure you go through this guide closely dortania.github.io/OpenCore-Install-Guide/config-laptop.plist/coffee-lake.html#acpi
I have follow the steps using your video guide. I am using fenvi T919 PCI-E WiFi Adapter. I am having bluetooth issue. It could not on. Can you help me to resolve issue?
HI followed your guide together with Dortania and managed to get it working now I have Ventura installed but I am having mouse lag issues, my mouse will randomly be laggy but the OS is not lagging. I have mapped my USB using your method already and all my usb ports work. Mobo: ASRock B660M Pro RS/ac CPU: Intel i3-12100F GPU: Gigabyte RX470 Ram: Lexar Ares 16GB running at 2666Mhz Storage: Lexar NV620 256GB SMBIOS: MacPro7,1 Please let me know what I should try to fix this
I have a desktop PC with Windows 11 core i7 Please explain How tonstall macOS Seqouia on 12th, generation systems | OpenCore Please, if possible, thank you
OC configuration failed on after booting, how to fix that? All my steps are correct and the config.plist is correct to , what is the mistake I made then? Please help me to fix that
Hi, I am having a black screen issue (I have whatever green) as soon as I boot the installer (for the first time). It goes to the apple logo, loads, then just black screens! Do you know how to fix this/ why this issue is being caused? For reference, I am using a HP 612 X2 G2 with 8GB of ram, 256GB SSD, and a i5 Kaby Lake/7th gen. Thank you!
@@Studio3BRocks sorry for my bad English . I just asking you that You are used your iGPU for headless mode or Computing task only Right. and your AMD RX 580 provide display output. this Two GPU are showing up in your About This Mac & System infomations ?
Just a little bit problem that I have booted into the recovery of the MacOS (Online Installer) and there is no Internet connection in my PC. I tried to throw all off the Ethernet kexts into th Kexts Folder but it still don't have Internet. Does anyone have seen this problem? I use H81 Gigabyte DS2 and i3 4130
Creating the usb is a bit different. I have a video on my channel that shows how to using from Big Sur to Monterey but the steps are basically the same for Ventura.
@@Studio3BRocks thanks, i'm on catalina now. as for the usbmap, is it just a simple matter of copying over the usbmap.kext? then i won't have to do the maps again right?
AMD RX580 is natively supported for macos. I selected MacPro7,1 SMBIOS and dGPU device properties. It was recognized out of the box. Sonoma has some issues with WiFi support for my PCI card so I will wait to keep it installed however I did post a video about upgrading from the App Store. Enjoy.
@@Studio3BRocks yeh this had been super helpful, i was able to get everything up and running in just 2 days along with some help on various forums . thanks!
By the way these are my laptop specs: I7 4700mq haswell Double graphics: Nvidia gt740m(for 3d rendering and games and editing) Integreated graphics hd 4600(for changing screen resolution) Tactical screen Keyboard and trackpad integraded Laptop model: hp envy 15 touchsmart
Im seeing some tutorials from youtube and that looks so easy. This one is totally different. GIad that I saw your video. Hope this will work on my PC: i5 11400 Asus rog b560i gaming Asus rog rx5600xt 16gb 3200 ram Nvme drives
![BOWKYLION - วิงวอน (ex-change) [Official MV]](http://i.ytimg.com/vi/cLdnZWDaO-w/mqdefault.jpg)
This guide is the most accurate one that i found. Thanks to that and to the dortania guide i hackintoshed a MSI GL75 10th gen I7, 32gb of ram and it worked perfectly almost first time (except for wifi and bluetooth)
did you manage to fix it?
Thank you for this video, i already did a build before with AMD. Switched now too Intel, was quite a hassel with Raptor Lake (13th Gen, there is no official guide). But nice too have a video like this and go trough everything along side too checkup.
Got everything working, even P-Cores and E-Cores so it has fully support till 5.4 GHz :)
MacOS: Ventura
Intel i7 13700k
AMD 6600
Nice work!
Can you please tell me how you did it? I have intel i7 13700kf and Nvidia 13700kf. Please help
Doesn't work on Nvidia @@sumitsamanta7650 . I am also very curious about how he got it to work though
@@sumitsamanta7650Nvidia... What?
Great tutorial, I got mine working because of this. Ventura, Asrock Z390, Core I7-9770K, Radeon 6800 XT.
The set up progress it is so real like you get to choose your language at the beginning just like a normal MacBooks
Its the real deal
@@Studio3BRocks ah
Gotta tell ya this is by far the most in depth and accurate guide I’ve come across.I have a system similar to yours. I7 4790k but it’s in an hp g1 800 sff paired with an lp rx550 4gb. I patched the Gpu and with the t919 everything works flawlessly. Only issue I’m having is I cant use the hdmi port on the Gpu for dual monitor support. I added framebuffer patches for the connector and went from no signal at to a color flash followed by blank screen to no signal every 10 seconds. I dont quite understand how to patch the busid but I’m guessing that’s what I need to do since I’ve tried everything else. Funny thing is I can use an hdmi cable if I plug it into a dp to hdmi adapter via the dp port. Smbios I use is iMac18,3. Could that be my issue?
I can dig into it more . I thought 18,3 is a good smbios. You can try a different smbios. Also is your bios settings correct? Is CSM disabled? I got a black screen with CSM enabled and disabling it seemed to solve it. Other than that it might be other config settings we need to look at.
Your guide was truly very useful. I cant thank you enough!!!
And I managed to setup a Intel B660M and i3 12100 based system with it. But I had to struggle & search around the internet to get the installer run properly, but in the end the it was very well worth it and your guide IMMENSELY helped me out understanding the all the details.
I have following request for you:
Please make a video guide on how to maintain and keep the hackintosh stable.
Please make a video guide on dual-booting with existing windows installation.
And lastly if possible please make a guide for 12th and 13th Gen Intel platforms opencore and plist setup. The reason I'm requesting is because NONE of the youtube videos goes this deep and comprehensive like your videos. (I watched close to 80-90 videos and almost all of them were based on pre-baked EFIs and installation ISOs ).
Kind and best Regards!!!
1) keep hackintosh stable - OpenCore is very stable once you configure it right. 2) dual bootong - great idea for a video, 3) - would love to if I had the funds to purchase this equipment... Thanks again
@@Studio3BRocks I managed to dual boot with windows 11 and Mac os ventura. opencore is awesome.
nice work@@p4k8g5i7
You are a true Technologist my brother 💯 Thank you for making this video. 🙏 Watched it fully last night along side your 26 min version and it really helped me to not only finally understand the process but also how to try it now myself without a configurator. 💪 Please keep em coming!! 🔥 LIKED & SUBBED
Thanks for the feedback !! Glad to help share the knowledge.
Great video and info - needed a bit of hand holding as my laptop requires a lot of Kexts and arguments in the config.plist and it's a bit overwhelming - great job!
hope you got it working!
you're the boss of Hackintosh
Thank you for going over every? most? steps in building the USB installer.
One difference I saw with mine is that.. during the first reboot, instead of text based loader screen,,, I had GUI icons? other than that. all worked.
Also, during the setup screen, I didn't get choose language but straight to country selection. Also, my USB Applekeyboard did not get recognized. odd.
You probably configured the gui picker you can turn it off though. Also you can set your language in the config. Also you need to map your usb or use the default kexts
maybe you have opencanopy.efi?
Start::512:successfully initialized AHCI controller (frozen in the log m in recovery dmg file)
same here, did you suss out how to fix it?
if you need more troubleshooting let me know
Amazing tutorial, I was wondering if it works for laptops as well
Similar - but different config.plist settings
Great guide! However, I don’t know how to fix my HDMI ports on my laptop not working
What’s your gpu?
This is useful. Thank you
Would be a lot of expense for you but any chance of doing a Ryzentosh in depth guide of the newer way of creating R/Hackintosh I keep getting things wrong and it’s very frustrating 🙏🏻🙏🏻🙏🏻😉😉😉 still got a stable Catalina build from way back when, in the Opencore 0.5.9 Days 🤣🤣🤣
I would love to do a Ryzentosh. Please consider donating to the channel or becoming a member.
Positional parameter cannot be found.
I'm running stable Catalina Hackintosh using clover (Morgonaut's old guide), What are the upgrade steps to Ventura? Any tutorials for that?
I would follow the same tutorial but instead of formatting your disk just install Ventura which should execute an upgrade
Any specific reason to use SSDT time on linux while you can run it on Windows it self
I don’t recall the reasoning behind it at this time!
🎯 Key Takeaways for quick navigation:
00:00 🖥️ *The video is about installing macOS Ventura on a Haswell PC using the Windows 10 operating system.*
01:20 📦 *You'll need specific hardware components like an AMD GPU (Nvidia not supported), SSD storage, an Intel chipset for Ethernet, and a compatible Wi-Fi/Bluetooth card.*
02:59 💻 *You can choose between Windows 10, Mac OS, or Linux as your primary operating system for the installation process.*
03:26 ⚙️ *Make sure to update your BIOS to the latest version before proceeding.*
06:01 📀 *Creating a bootable USB drive using Rufus is recommended for the installation process.*
13:52 🐧 *If generating ACPI SSDTs, using a Linux installation on a separate USB drive is suggested for efficiency.*
16:34 📂 *You need to gather various files, including drivers and EFI files, and configure your config.plist file.*
26:56 🍎 *Selecting the correct SMBIOS (system profile) for your hardware is crucial for a successful installation.*
30:53 ⚙️ *Configure your computer's BIOS settings as recommended in the Dortania guide for the installation process.*
31:36 ⚙️ *Configure BIOS settings for Hackintosh by going to the Advanced section and ensuring proper settings, such as SATA configuration (AHCI), disabling VTD, and adjusting Graphics configuration for dedicated graphics cards.*
36:29 💻 *If you encounter a black screen during installation, consider downloading and installing "WhateverGreen" to address graphics-related issues.*
37:35 📝 *Disabling Compatibility Support Module (CSM) in the BIOS may be necessary to ensure a successful Hackintosh installation.*
38:27 🌐 *After installing macOS Ventura, use a tool like "Mount EFI" to access the EFI partition and copy necessary files from your USB drive to your hard disk's EFI partition for proper booting.*
41:05 📦 *To configure USB ports, use "USBMap" to identify and map the USB ports on your computer. Create a USB map, copy it to the EFI partition, and update your config.plist for USB configuration.*
44:13 🚀 *Transition from debug mode to release mode by downloading release versions of necessary OpenCore files, drivers, and kexts. Replace debug versions with release versions for improved performance.*
48:22 🖥️ *Customize the OpenCore graphical user interface (GUI) by configuring options like "picker mode," "picker attributes," and "picker variant" in your config.plist.*
50:27 🔊 *Optionally, enable the Mac boot chime in OpenCore settings and adjust boot arguments to remove verbose mode for a smoother Hackintosh experience.*
Made with HARPA AI
45:10 45:12 45:13
Best Guide ever thank u verry much!
Hi, thanks for the video. i wanna ask why did you need to do it in linux live? Not directly in windows?
Just another way to do it
Hey brother great video, just one question after successfully installing OS can I boot into my windows 10 back, like this process is a dualboot or will it override my windows?
You can if you use a separate disk
@@Studio3BRocks you can separate one drive to 3 partitions of EFI, mac and windows, you can dual boot macos and windows with a single drive like this
Hello! Thanks a lot for your guide, it was extremely helpful) Did you able to make sleep working? In my case i trying many different methods and it won't work((
no i turned off sleep :/
@@Studio3BRocks I tried many different methods in the internet but nothing worked:( I guess we need some DSDT patches to start it work properly, cuz previously in the Mac OS Mojave with clover it worked great
@@MsVladmen yes unfortunate for this older model pc (haswell). If i were to start over I'd go the OpenCore buyers guide and get all compatible components.
thank you bro great video
Glad it helped
When i go to bootmenu for the first time to install macos. than i click it says ok. and stuck here.. any idea what is wrong... please help me
same for me
I get the same thing happening.. I feel like he skipped some steps on this tutorial. He should do it again but properly this time
Shame Studio 3B made some mistakes, and also didn't do the gpu whatevergreen install. He should redo this video again and be proper this time
Hi, you can get the opencore-**.txt file from your most recent boot attempt off your EFI partition (assuming you have debug turned on). You can take a look at where it is stalling and go from there. Let me know if I can help more.
Hi, @protos2901 yes I am using Whatever green, and chose the right DeviceProperties for my AMD RX580 GPU. Also a correct SMBIOS is important too.
Thank you! Got mine up and running!!
lucky
I followed your guide, it was very detailed! I'm having an issue where no drives show up on the MacOS install screen. Even when I click show all devices, I only see the installer. I made sure to set my BIOS settings according to the Dortania guide (i.e. AHCI mode, etc.). Do you know why this could be? My machine has a 10700k and my motherboard is an MSI MPG B460i.
Do you have hfsplus.efi on the usb?
The video is entitled "Hackintosh Ventura - In-Depth Guide (Windows Method)" Now out of nowhere we have Ubuntu configuration added to the mix. Time to look for a better Hackintosh video!
That’s the beauty of the World Wide Web. Do as you see fit!
Hope this steps will work on my old laptop intel i3 (Arrandale cpu code name), legacy bios gateway
I would start here. dortania.github.io/OpenCore-Install-Guide/config-laptop.plist/arrandale.html
Hey man, i followed this tutorial and installed ventura, i needed that for xcode and now i see that ventura doesn't support it and i really don't want to spend another 10 hours fixing issues, can i upgrade to sonoma directly from software update? Normally like on MacBooks or do i need to redo it all over again:,) thank you for the great tutorial anyways:)
Upgrade. Maybe WiFi won’t work. No guarantees .
@@Studio3BRocks hey man justa quick one at 48:23 i did these steps and didnot touch the boot chime, before doing all that it was showing digital out under the sounds tab which is gone now, it only shows my microphone that is connected over USB, i did undo of all the stuff that i had done, what should i do in this case?
big thanks 🥳🙏
You're welcome 😊
After many tries, I successfully got up to the USB Mapping part (last step before removing verbose and debugging) with my HP ProDesk 600 G4 and after a long reboot I have no keyboard and mouse or any USB ports. Not sure what I did wrong. Looks like I am starting over.... again :(
Did you leave other usb kexts in there too to confuse it?
24:18 I'm wondering if you even need to define device-id as it seems your CPU has HD 4600 instead of HD 4400 (that latter needs to be faked as HD 4600?)
Same with PciRoot(0x0)/Pci(0x1b,0x0) section - if you are not going to use it, then I think it is good to remove it.
Interesting. Could be worth cleaning up a bit. Thanks for watching.
Did the bios settings that enabled and disabled interfere with the performance once you are in windows? Thanks
None that I have noticed
I keep getting the "In Memory Panic Stackshot Succeeded" error. And other times it's giving me a ""Kextlog: kernelmanagerd is not active" message. I can't get past the first wall of text screen. Please help
Hello sorry for the delay. Let me know if you still need assistance. I can give you my email.
Hello help me trackpad not working on disk utility and installer option
All kext of voodoo are installed
i5 8th gen
Intel UHD 620 graphics
Id have to look at your EFI. Make sure you go through this guide closely dortania.github.io/OpenCore-Install-Guide/config-laptop.plist/coffee-lake.html#acpi
I have follow the steps using your video guide. I am using fenvi T919 PCI-E WiFi Adapter. I am having bluetooth issue. It could not on. Can you help me to resolve issue?
i can help, let me know
I follow your all guides but I always stuck at " Failed to detect supported SuperIO cheap" can you help me to slove this.
Love from Nepal❤❤
I would contact the wider hackintosh community with searching. Sorry I have not seen this error.
plz post the Z790 Ud ax 13 gen i9
Please consider donating to the channel or becoming a member.
Hi can you show me where is the part you install vga driver.. because it should be not work automaticly right?
macOS either supports the card natively or it doesn’t no vga driver
I am getting stuck on a grey screen after the first apple logo while first booting … any help ?
Enable debug mode
HI followed your guide together with Dortania and managed to get it working now I have Ventura installed but I am having mouse lag issues, my mouse will randomly be laggy but the OS is not lagging. I have mapped my USB using your method already and all my usb ports work.
Mobo: ASRock B660M Pro RS/ac
CPU: Intel i3-12100F
GPU: Gigabyte RX470
Ram: Lexar Ares 16GB running at 2666Mhz
Storage: Lexar NV620 256GB
SMBIOS: MacPro7,1
Please let me know what I should try to fix this
is this a graphics acceleration issue?
Hey I fallowed your tutorial and I keep getting halted on critical error when I go to do first boot any suggestions on how to fix ?
Hopefully when you go through the steps again you were able to resolve this issue. Any luck?
Is it work on hp z-book labtop with core i7 4700h with haswell cpu type ?
One way to find out
Why doesn't it work on a laptop with integrated AMD processors?
Either different config settings or unsupported hardware
I enabled csm and now I can’t get back into the bios
That’s strange. You might need to reset CMOS
@@Studio3BRocks it’s love fixed the problem and have had macOS Ventura on it for about a month now
Hello, have got a question : Does it work with an apu, like the ryzen 7 4800h?
I have not tried AMD cpu yet but I’ve heard of others having success.
I have a desktop PC with Windows 11 core i7 Please explain How tonstall macOS Seqouia on 12th, generation systems | OpenCore Please, if possible, thank you
I’ll wait till Sequoia is released
OC configuration failed on after booting, how to fix that? All my steps are correct and the config.plist is correct to ,
what is the mistake I made then? Please help me to fix that
Cheick if u're efi file matches u're CPU generation (if it's haswell u need a haswell efi file )
if you want me to troubleshoot, contact me via apllc.tech
Will it support my pc , I want to install as dual boot windows and mac
Ryzen 9 7900X
asus prime x670p csm
32gb ram
ASROCK RX 6600 CHALLENGER 8GB GDDR6
Check out the dortania guide
hello , i have a question , i don't have Ethernet port on my pc can y o u throw it and install ventura OS normally ?
I think you will struggle with Apple ID and things. I haven’t tried it offline in a while.
What about paid apps on store it is cracked or stile paid spatially final cut pro is we have method to cracked??
Apps work fine. Paid apps work fine
@@Studio3BRocks can I find. Method to use them freely
I cant login to the appstore but if can login to applemusic, imassage, facetime and system settings, can you give me a clue what is going on please
what error are you receiving? Did you make sure your serial number wasnt already taken?
Can hackintosh be the reason of slowly bricking parts of laptop?
Unlikely
I create the USB Installerr from my PC for my laptop. Does it matter?
You can do that
Hi, I am having a black screen issue (I have whatever green) as soon as I boot the installer (for the first time). It goes to the apple logo, loads, then just black screens! Do you know how to fix this/ why this issue is being caused? For reference, I am using a HP 612 X2 G2 with 8GB of ram, 256GB SSD, and a i5 Kaby Lake/7th gen. Thank you!
More than likely something’s not right in the device properties section of your config.
@ I am restarting the entire process again, do you have any idea of a good SMBIOS to pick for sonoma for my laptop?
If you’re using an iGPU, try iMac18,1
hey, is there any method to download macos ventura full iso/dmg offline version on windows PC?
Yes use the dortania guide and go to the windows method
Hey, after the first phrase of reboot, it went to the reboot loop, any idea?
Check your drivers, config, smbios. Could be a ton of things… hard to say
any ways to get the log?
@@Studio3BRocks
everything went fine. but my keyboard, trackpad is not working. The internal HDD is not showing up in disk untility of mac. any solutions. pls
For the keyboard, trackpad etc, take a look at the Voodoo kexts. As for the hard drives not showing, perhaps you have an incorrect Kext in your EFI
change sata mode to AHCI
i get a error that says that python is not installed but it is infact installed
You can either use the App Store or download it. There might be two ways
HI My system Configuration will be AMD Ryzen 5 3400G with Radeon Vega Graphics 3.70 Ghz . Can i Install MacOS Ventura with these steps
we can certainly try! let me know.
can you conform IGPU show in Graphic/display tab or its only show DGPU ?
I don’t quite understand your question
@@Studio3BRocks sorry for my bad English . I just asking you that You are used your iGPU for headless mode or Computing task only Right. and your AMD RX 580 provide display output. this Two GPU are showing up in your About This Mac & System infomations ?
@@prakashsinghmeena1022 yes I’m using igpu for computing tasks only. It does not show in about this Mac for me
@@Studio3BRocks thank you.
i have i7 4th gen with gtx 720m graphic and intel hd4400 will ventura work?
Look at the dortania hardware guide
The Apple folder isn’t appearing within my efi partition what should I do?
Just need OC and Boot folders at first
@@Studio3BRocks I appreciate the response I found the issue, it wasn’t the efi folder it was my bios not reading the boot efi
@@travisroach8847 are you up and running now?
@@Studio3BRocks I am I just had to set the path to the opencore.efi
Just a little bit problem that I have booted into the recovery of the MacOS (Online Installer) and there is no Internet connection in my PC. I tried to throw all off the Ethernet kexts into th Kexts Folder but it still don't have Internet. Does anyone have seen this problem? I use H81 Gigabyte DS2 and i3 4130
they were likely conflicting. Try the Realtek driver only github.com/Mieze/RTL8111_driver_for_OS_X/releases
Will it work pretty much the same way if I'm creating the usb on a current hackintosh? I need to upgrade to ventura from an older version
Creating the usb is a bit different. I have a video on my channel that shows how to using from Big Sur to Monterey but the steps are basically the same for Ventura.
@@Studio3BRocks thanks, i'm on catalina now. as for the usbmap, is it just a simple matter of copying over the usbmap.kext? then i won't have to do the maps again right?
@@evenaicantfigurethisout copying it has worked for me in the past .
You can do the ssdt thing in windows also
Yes but it needs to be on the machine your installing macos on.
i cant find anything for alder lake laptops with nvidia gpu...can you help me out
I recommend going for a more supported AMd gpu if that is an option
Yeah but I don't have one 💀
Is It Work With Ryzen 3400g processor ? and motherboard B450M H?
You’ll have to try
Can you please redo this tutorial again without skipping steps. I would like to see how to install the RX 580. Thank you
It is recognized by macos. You just need to do the device properties correctly
@@Studio3BRocks The device properties is what I want to know. Please redo the tutorial again
@@galmadon5052 I've redone the tutorial about 4 or 5 times. But sure maybe for the next macos
@@Studio3BRocks Yes Please. Do it for Sonoma. Thank you
AMD RX580 is natively supported for macos. I selected MacPro7,1 SMBIOS and dGPU device properties. It was recognized out of the box. Sonoma has some issues with WiFi support for my PCI card so I will wait to keep it installed however I did post a video about upgrading from the App Store. Enjoy.
I want to build for i7 12700k running on gigabyte b760 M, gpu radeon rx 560 please can you help me with this?
yes I can attempt to help you please let me know if you are still interested.
Hey is there any method that can make nvidia gpus work on ventura?
Very unlikely for Nvidia GPUs to work
Look into Open Core Legacy Patcher
When I click on the usb drive on the boot menu, it goes into the Apple logo but does nothing? It’s just stuck, is there a solution to that?
You need to put it in verbose mode and start debugging it.
@@Studio3BRocks alright thanks!
@@Studio3BRocks it’s giving me something called a “standalone dmg root hash error” is there a way to fix it
@@Kennynotfoundd double check your config.plist particularly the Booter section
@@Studio3BRocks alr I’ll try thanks 👍
is Whatevergreen ktext required?
Yes
@@Studio3BRocks yes I saw later on in the guide you mentioned it was missing
Im pretty sure its required. I may have missed it in the tutorial. @@jazzbeats8168
@@Studio3BRocks yeh this had been super helpful, i was able to get everything up and running in just 2 days along with some help on various forums . thanks!
Do it on Linux next
Sure. Which distribution would you like to see? Do you mean make a macos installer from Linux?
@@Studio3BRocks I mean following the same process but using Linux instead of Windows. Any distro will do.
great idea
@@Studio3BRocks Thank you.
sorry, can my ryzen 5 3550h work with this guide
Your EFI would be much different
it says cant boot, press f1 to retry please help here too
Are your bios settings correct?
@@Studio3BRocks yes my bios setting is correct
my laptop is dell latitude 5490 i5 8th gen
do you have an OC and a BOOT folder in your EFI folder?@@TalhaKhalid
@@Studio3BRocks yes brother
please switch to my discord channel discord.com/channels/1089950438394167326/1089950441053372539
Plz help idk know why my wifi isn't working when i'm on recovery mac os page
I’ll need more information you can contact me at apllc.tech
Ok thank u 🙏🏻 i’ll contact u over there
@@Studio3BRocksi’ve send it to u a message. Please answer if u got the time . Thank u and sorry for the embarrassment 🙏🏻🙏🏻
By the way these are my laptop specs:
I7 4700mq haswell
Double graphics:
Nvidia gt740m(for 3d rendering and games and editing)
Integreated graphics hd 4600(for changing screen resolution)
Tactical screen
Keyboard and trackpad integraded
Laptop model: hp envy 15 touchsmart
Hi, I sent you an email@@Kinane_ot
My wifi does not work in Hackintosh
Sonoma and above will have Broadcom WiFi issues also.
I cant dowlonad MacOS :(
Why?
Got running off the USB. Used mount efi and copied the two folders to the root of the mount but pc won't boot. Thoughts?
It only boots from usb and not from hard disk efi when you remove the usb? Did you properly choose the boot device in the bios?
15:09
Is this dual boot or override windows
This is using a separate windows machine from your hackintosh
Im seeing some tutorials from youtube and that looks so easy. This one is totally different. GIad that I saw your video. Hope this will work on my PC:
i5 11400
Asus rog b560i gaming
Asus rog rx5600xt
16gb 3200 ram
Nvme drives
At first glance it should. Rocket lake. Use Comet Lake CPUID 0x0A0671
@@Studio3BRocks thank you for fast reply. Its rocket lake right, any reason why i need to use the comet lake? Thanks
@@jrdulce I just got that off the opencore guide
@@Studio3BRocks sorry for not getting your point. I gonna use rocket or comet? Ty
@@jrdulce you’re CPU is a rocket lake, but you need a comet lake CPUID
How about XHCI-unsupported.kext and USBInjectAll.kext we no need use it?
USBInjectAll is an older way. I have no experience with xhci unsupported.
your discord server link?
At this point try the hackintosh community discord link found on Reddit for better 24/7 support
I’m getting a permission denied when I try to run cp -r Results/ /mnt/ what do I do 🥲
You need sudo in this case
@@Studio3BRocks I managed to figure It out yesterday fortunately but thank you!
On installing macos
It isn’t installing on APFS instead it say use extended ….. etc I don’t know what to do all of my disk are erased🥲
I can help you if you reach out to me on my contact apllc.tech/contact
it says that i need an internet connection to install macOS, but i cant get the internet to work
Get the right kext for your Ethernet nic
One question if I install mac on my ssd will I be able to use files from my HDD like photos
Yes
OC : failed to load confiquration, please help
Do you have config.plist in the right place?