after 25 years I have had to say goodbye to my yard and workshop, I live on a boat so have had to get rid / pass on a lot of tools from lathes to engine cranes and 5 trucks plus a live on bus ranging in physical weight from 3000kgs to 7500kgs, watching videos like this makes me happy to see people still showing how to make things. I have a waste fuel heater and it works well, no external flame so clean water free hot air. Keeps me toasty on the cold days / nights.
It sounds like you've made quite a big change in your life! It's great that you found a way to stay warm with your waste fuel heater. Best of luck with your boat life and keep enjoying those creative videos!
Iv been thinking about doing that ,buying a pontoon, and building a styrfoam shach on it and sail away . and I want to use waist oil to produce hot water, heat and electricity .
عمل رائع شكرا لك❤️ احب ان اضيف لك شيئا تستطيع ان تضع بايب نحاس لولبي حول حجرة الاحتراق ويمر الماء من خلالها بدائره مغلقه سوف يصبح لدينا ماء ساخن للاستخدام بنفس الوقت👍 اشكرك على هذا المجهود الرائع انت تستحق المتابعه والنشر😘
شكرًا لك على هذه الفكرة الرائعة! استخدام بايب نحاس لولبي حول حجرة الاحتراق لتسخين الماء فكرة مبتكرة جدًا. سعيد بأنك استفدت وأتمنى لك المزيد من النجاح! 😊
Very cool, the Buick Dealership I worked at used a waste oil heater to warm the shop in the winter, all of the used oil and gasoline from oil and fuel filter changes went into a 100 gallon tank thru the spring and summer and was full by winter!! At the start of winter we would clean the burner and light it, with the 10 overhead doors being opened thru the day to bring cars in and out of the shop it was a cheap way to heat!!!
I worked for a towing company/scrap yard and they used a waste oil furnace for the shop. It worked quite well. It did have some problems occasionally. I went in on a Saturday to find the whole shop filled with smoke cause the heat exchanger cracked. It was missing paint off the side of the furnace housing because it got oil with too much gasoline in it one time and it got extremely hot.
@juliogonzo2718 With all of us Mechanics opening and closing the Garage doors all day it would have cost a fortune heating with natural gas, plus it also heated the body shop too!!! We did have natural gas heaters in the service lanes but they were efficient enough for that use!!!
Yes thank you for watching our video it's great where you are also using a waste oil heater right? Yes waste oil heating water costs extremely low and to make one directly is not worth much money and waste oil is something that is almost available right? Yes when done correctly it has a very high temperature of up to 700 degrees Celsius and there is no black smoke so when it enters the air when the temperature is high when it is chemically it will burn completely creating a blue flame like gas Thank you for giving us positive words do you have any suggestions for us to do better Please let us know We will improve the product further to contribute to bringing more value and benefits to audiences around the world Thank you
Well done....Remember safety is paramount....Can't be used indoors as products of combustion are toxic and cause death...Can only be used in a well ventilated area...that's with any combustion process....recommend using a stainless steel flue vented directly outside of the heating environment so you get the BTU heat from the flue as well.Stay safe.
Great advice! Safety is crucial-ventilating properly and using a stainless steel flue ensures safe combustion and maximizes heat efficiency. Stay safe!
Love it makes me think of cooking a pot of stew or beans on top of our kerosene heaters back in the day! Enjoyed thanks for sharing God Bless u and urs!
This is true ha. However I wouldn't cook anything on this. Nor would I want that venting inside a living space or workspace. Old/used motor oil contains some pretty narley chemicals and if you I breath it long enough can cause some pretty bad health issues.
I totally agree with a post further down. It’s consuming oxygen and the fumes it’s producing. This should only be used in a well ventilated area or outside. The flame 🔥 color is correct for an oil / waste oil burner. I had a commercial build waste oil furnace in my garage. I loved it basically free heat other than the tiny bit of electricity ⚡️ for the fan and tiny pump for the oil. It was 60,000 BTUs on a continuous run no thermostat. Go out start it , have breakfast and then the garage would be starting to warm up. I did a lot of driving and a lot of oil changes, so it worked out perfectly. The furnace would burn 1/2 gallons per hour or roughly 2.7 liters.
That's a minimum of 250 gallons per winter. That would be over 20 oil changes on a semi engine. It would take several semis annual oil changes to supply one such heater.
That is why you let people who live around you know that they can dispose of their waste oil for free by just leaving it at your facility. There is a place near me that allows anyone to leave waste oil with them, and I have seen the setup they have to filter and burn it, very neat and useful if done properly and safely.
@@Absaalookemensch Hi, you are correct if I ran continuously. However this was in my garage. Also ran every weekend and maybe a few nights during the week. I was changing oil in my daily driver, my girlfriends, once in a while in 3 other cars and I was racing PRO Rally at the time. The rally car got the most oil changes. Especially when something bounced up and destroyed the oil filter. Very quick end to that race.
Все хорошо и красиво но есть один минус это нет дымохода. Такая штука рано или поздно выжгет кислород из воздуха и засерет его продуктами сгорания этой отработки. Дым хоть и не видимый но запах по любому есть.
А чем масляный электрообогреветель хуже то ? Походу он и дешевле будет в эксплуатации, и экологичней. Эта байда хороша где ляктричества нет и мазуту тырить можна. А так то буржуйка понадёжней. И омлетик пригатовить с грогом, и жги чё под руку попадёт. От соседскога забора, до отходов мебельнога канцерна.
Lanair makes a waste oil burning/ forced air heater, that is EPA compliant. And YES, you can burn dirty oil, cleanly, as long as you preheat the chamber first.
"Yes"! To The "Truth"!!.. The "Word"!! Of "GOD"!!. "No"!!!. "ROMAN"! "Sunday"! "God" Genesis 1:( 14-18) "GOD'S"!!.. "Calendar'!!.. Genesis 2 : (1-3)"'GOD'S"!!..Sabbath"!!.. "NO"!!! "ROMAN" "CALENDAR'S" For "Worship"!... "Not"!.. "AT"! "ALL" FOR "ADAM'! AND "EVE'! "MOSES"! AND "AARON"! The "PROPHETS"! "Even'! for Our "Own"! "Savior"! "YESHUA"!! "LORD"!! OF THE "SABBATH"!! Matthew 12:(8) Mark 2:(27-28) "NO"!. "ROMAN"!. "CALENDAR'S"!. For "Worship"! "AT"! "ALL"! For The "People"! Of "GOD"!! in This End "Time's"! Exodus 12:(1-2) Ezekiel 20:(20) Isaiah 66:(23) John 14:(15) John 15:(10-11) "HONOR"!!.. and "GLORY"!!.. To The "CREATOR"!!.. "GOD"!!.. Revelation 14:(6-12) "Day's"! "Month's"! "Year's"! Exodus 12:(1-2) "Moses"! and "Aaron"! 40"Year's"!.. in Mt. Sinai 40 "Year's"!.. in The "DESERT"! "Land"!.. Of "Egypt"!.. "Receiving"! The ("Mana"!) "Keeping"!.. The 7th Day Of "Rest"!.. The "Sabbath"!!.. Of "Creation"!!.. And "THEY"! "HAVE"! "NO"!!!... "NEED"! Of ANY "Man" "Made" "ROMAN"!?... "Paper"!!?.. "Man" "Made" "Calendar"! Of "ROME"! "False"! "ROMAN"! "Calendar's"! All "United"!!! in "ONE"! 🌎 "ONE"! "World"! "ORDER"! 🌎 "ONE"! "Word"! "RELIGION"! 🌎 In "ONE"! "Man" "Made" 🌎 "CALENDAR"!!! Of "ROME"!!! 📅 "False"! "Friday's" for "Islam" ☪️ "False"! "Christian" "Saturday" ✝️ "False"! "Christian" "Sunday" ✝️ for "False"! "Christianity" ✝️ "False"! "Invented" "God" "False"! "Adoration"!... 2 Corinthians 4:(3-4) The "God" Of This "World"!!! 🌎 "Have"! "blind"!!! "Their's"! "Mind's"! 2 Tesssalonians 2:(1-13) "GOD"!!..Will "Send"!.. "Strong"!... "Delusion"!... "One"! "Delusion"! Of "Many"! "Other's"!... To "Come"!. Daniel 7:(25) "Will"!?... "Try"!?... To "Change". "Time's"!!.. and "GOD'S"!!.."Law"!!.. it is "Blasphemy"!... Lie's"!..."Sin"!... Revelation 20:(13) "They"! "Ware"! "Jughead"! "According"! to Their "Work's"! "Salvation"!?... in "Lie's"!?... Of "Course"!!!... Not"!!!... "Salvation"!? in "Pastor's"!? "Family's"!? "Husband's"!? "Wife"!? "Son's"!? "Daughter's"!? "Neighbor's"!? "Pet's"!? "Totally"!!! "Imaginable"!!! "Irracionable"!!! "Incomprehensible"!!!
@@PapaSnuffy love the spirit Papa Snuffy! Have a snort and remain calm. it is always later than one thinks! Whatever doesn't kill you makes you stronger they say.
I like it. Its burning efficient with the blower fan so should be minimal fumes and separating the burning chamber from the outer hot air chamber just completes it. Works just like a diesel heater so using it as a heater should be good so long as your welds dont have holes😉
@@dakotachristianson3756 Not possible, carbon monoxide would still be a concern. I think the stove would have to operate outside with the secondary heat going into a structure.
@@dakotachristianson3756 even though he didn't make it very clear, I'm pretty sure the stove part goes on the outside of the building and the flexible duct that he showed gets routed to blow the hot air inside the building.
@@josephoxenham6142if your not familiar with a properly set up waste oil burning stove than just say so lmfao. You have not the slightest clue of what your talking about. I've been around them for years and never a health concern one set up right they are very efficient. the epa approves and encourages there use, as it is safer to convert/burn a potentially hazardous waste onsite
Awesome build. I’m thinking of building one of these, thank you for the video. I am not the one to put down anyone’s hard work. I’m just wondering about the tack welding technique. Just a suggestion; If you play around with your tuning knobs, adjust your amperage down and adjust the wire feed comparing how fast the wire melts per amp temperature, you could get a continuous flow to form a solid welds with better penetration instead of tack welds.
@@AaronSchwarz42 Muliptle tacks, alternating sides in a pie cut pattern similar to how you tighten lug nuts, will prevent the warping. The amount of tacks will vary depending on size. Then follow up with multiple good penetrating beads in a similar pattern eventually connecting all your clean beads (lay some dimes). Will most importantly penetrate, and prevent any pinhole leaks as well, without warping. Finish by chipping, grinding, and polishing smooth.
Thanks for the suggestion! Adjusting the amperage and wire feed speed for better penetration and continuous flow is a great idea for improving weld quality. I'll definitely give it a try!
@@esra_erimez It's false, he's using Gas. The oil almost doesn't burn, if you blow it it goes out. Fire can be seen coming out of the center blower inside the oil container. If it blows air it should not ignite, only stoke the fire in another place, but flame comes out because it blows Gas.
Главная причина почему это полная херня, если забыть про токсичность продуктов горения - это то что отработка на самом деле совсем не бесплатная и не дешевая (особенно в случае если все начнут использовать ее как топливо). Если где-то есть шаровой источник, например, у работника автосервиса, то даже там для нормального отопления может не хватить. Проще и дешевле бензином отапливаться или дизельным топливом.
@@РыбакРыбака-з3ы может где-то и добавляют воду в промышленных печах, но не в таких кастрюлях с кипящим маслом. Я полно историй пожаров знаю, когда отработка не отстоянная пыхает и превращается вся печь в фонтан из горящего масла. Причем у знакомого на производстве бахает даже промышленная печь так что стены трясутся, когда вода попадает. Можешь со мной не спорить, я сам эжекторную печь на отработке делал. Вонища от нее как в плохой котельной, учесть что у меня в трубу тянуло, а не как тут просто кастрюля с маслом. В итоге на дровяной котел ее переделал. И как писали выше цена на отработку подскочила, раньше за так нальют, где хочешь, а теперь 5-7р. за литр. Так что звон слышал ты, а я эту тему знаю.
Best design I've seen yet. Not sure I like the way you have the drip setup but that's easily changed. Other then the drip and making a tweak to the exhaust I'm definitely building this bad boy
Thank you! I’m glad you like the design. The drip setup and exhaust can definitely be tweaked to suit your preferences. Feel free to make adjustments as you build it!
my friend had a big one of these in his big workshop I thought it was fantastic and the large area was definitely not cold even with the bay door open all day
I seldom see any concern expressed about the heavy metal contamination in waste oil when burned. There is a great centerfugal oil extraction method that removes some of it but the only way I can imagine to be really sure is to "crack" it all over again and of course that takes quite a bit of heat too. How can you win?
You raise an important concern regarding the heavy metal contamination in waste oil. When burning waste oil, especially from automotive or industrial sources, it can contain a variety of harmful contaminants, including heavy metals (like lead, cadmium, and chromium), as well as other toxic byproducts that may be released into the air when burned. While centrifugal oil extraction can help remove some contaminants by separating out solid particles and some heavier impurities, it doesn't fully address the issue of hazardous metals that may still be present in the oil. To fully eliminate these contaminants, you would need a more complex process, such as "cracking" or refining the oil back to a purer state, which would require significant heat and specialized equipment. This process, however, is energy-intensive and costly, which could make it impractical for most DIY or home heating systems. To reduce the risks of burning waste oil, here are some possible solutions: Filtration: Advanced filtration systems could help remove larger contaminants, but they won't fully eliminate heavy metals or some of the finer impurities. Multi-stage filtration, combining mechanical, chemical, and carbon filters, can improve oil purity, but the risk of heavy metals remains. Exhaust Scrubbing: Installing a scrubber or an afterburner system in the exhaust could help trap or neutralize harmful emissions, including particulate matter and toxic fumes. This would help reduce the impact of burning contaminated oil on air quality. Pre-Treatment of the Oil: If you plan to burn waste oil regularly, you could look into oil refining or cracking methods that break down the contaminants before combustion. This might involve heating the oil in controlled conditions, but again, it would require a lot of energy and specialized equipment. Monitoring and Testing: Periodically testing the oil for contaminant levels (especially heavy metals) could help you understand its quality and whether it's safe to burn. You could also monitor the emissions to ensure they stay within safe levels. In summary, while it is possible to burn waste oil, doing so safely requires a multi-step approach to reduce contamination. The best way to win is to balance efficiency, safety, and environmental impact. Using clean or filtered oil, or even considering alternative fuels, could be an effective compromise for home heating systems.
@@lmtnThe combustion of used motor vehicle oils does entail the problem of heavy metals. Many heavy metals can be filtered out via fiber filtration and centrifuge equipment as I have at my shop. On the exhaust end, you can use the tendency of heavy metals to form sulfides to create a reactive filter - but this is outside the capability of a home shop. A cooling tower with soot traps might be more feasible if visibility is not an issue.
Yes everything is fantastic except the smell. It is almost impossible to operate it indoors.The one shown at the end of the video, working in a separate area is the best. Congratulations to the manufacturer!
Thank you for your comment! I agree, the smell can be a challenge indoors. The separate area setup definitely seems like a smarter choice. Appreciate your feedback and support!
You should catch up the air from outside. Otherwise, the heated air you blow into the next room will be the polutet Air from the burner! BTW In europe, the greens will hit you to death doing this. 😂😂
Great video, you are very good with your tools, and now I know what I'm going to do with my waste oil tank. I have a garage and a shop that both need heating and I'm tired of buying propane 👌 I was going to build a waste oil forge a while back but ended up buying a pre-made propane one, so ive just been filling my oil tank every oil change. This would be a great addition to the shop and garage 👌 and keep my tank from getting full to boot I appreciate your great work, you got a new subscriber here buddy 👍
Thank you so much for the kind words and support! I'm glad the video inspired you. A waste oil heater is a great way to repurpose your old oil while heating your shop and garage efficiently. Best of luck with your build, and welcome to the channel! Appreciate you subscribing! 👍
Thank you for reminding us so much Yes, the exhaust from burning oil also has a lot of toxic gases, right? You must be a professor Yes We will try to burn it far away from the area alone, just insulating it inside, is that okay? Yes, please give your opinions and suggestions Thank you
@@johannesmeyer-dunker6044 das ist wissenschaftlich erwiesen, nur weil du es mit bloßen Augen nicht siehst, heißt es nicht, dass sie nicht da sind. ES IST AUF KEINEN FALL GESUND ALTÖL ZU VERBRENNEN
In Soviet union we used and still using different kinds of waste oil heaters in garages and warehouses in rural areas. Most of them are handmade. So it's very economical.
Yeah, and the oil comes from dead bodies, so it's free. Just gotta point the finger at a neighbor and you'll have his whole family, oops, I mean a whole months worth of "waste oil".
We made a version of that. We made a combustion chamber and put it inside an old wood stove. Had a blower tube coming in the back. And I forget what we used for the oil tank but we would use air pressure to feed the oil. Used it many years. Before the boss got a propane heater.
Yes thank you for your sharing and receiving our videos Yes sir do you have any techniques to do better please leave us a comment and your feedback Thank you very much in I will follow your ideas to be able to improve better to bring more value to viewers Wish you a happy weekend
Excelente trabajo, muy bien estructurado...me gusto y lo pondre en practica...con ese aceite usado, se ahorra el gas butano en la cocina...me gusta bro...👍...
Es falso, esta usando Gas. El aceite casi no arde, si lo soplas se apaga. Se puede ver fuego saliendo del soplador central dentro del recipiente de aceite. Si sopla aire no debería prender, solo avivar el fuego en otro lugar, pero sale llama porque insufla Gas.
You're welcome! Glad you liked the video and measurements. A well-ventilated garage is perfect for safety. It's always a good idea to be prepared for emergencies. Stay safe and enjoy! 👍
@@lmtn Yes, practice. Practice and make sure you are comfortable. Anchor your torch hand on your free hand and make sure you can do the whole weld without repositioning. There are youtube videos on the subject. Refine your search words.
Vielen Dank für Ihre grundlegende Sichtweise. Ich hoffe, dass unser Edelstahltransformator nicht schwarz wird. Ich wusste nicht, dass er eine so hohe Verschmutzung aufweist . Nein, Sir. Ja, vielen Dank, bitte teilen Sie mir Ihre eigenen Vorschläge mit. Vielen Dank
Die Anlage steht draussen und bläsed warme Luft in die Bude. Ich glaube auch, dass da kein Geruch ensteht bei den hohen Temperaturen. Das Teil ist nicht schlimmer als die alten Heizölöfen meiner Eltern und Großeltern. Fragt sich aber nur, wo kriegt man so viel Altöl her, um einen ganzen Winter zu heizen.
Fucking hate welder know it alls Jesus Christ you people are insufferable. Been in the trades going on 30 years. There is no one worse than a “proud” welder
I'd say he's just showing everyone there interested the how to. I'll never understand why people go after the little shit instead of just being grateful to learn something that may indeed help one day@@americanandroid9952
I'm no pro but, experimenting with brass flux coated rods & MiG, the MiG laid down a better weld on brass than the brass in the MMA stick wand. Although today messing around with my 3-in-1 combo welding toy I put some tungsten in the MMA wand & went over welds I put with brass rods wrapped by hand with MiG wire & actually got welds to stick & hold to cast iron. Just an ace of trades playing around with a skill that is on the road to perfection. Any suggestions or helpful tips are appreciated.
They have been around for years .They used them in junkyards in the colder climates and used oil out of junked cars to put in them . They were about 1 meter in height .
@@jjb1974 umm, maybe add air vents along the pipe until you get a constant temp for drying? Or blower could cycle with the temp sensor? If you utilize the blower from the dryer as the blower for the heat source you would have everything you need i think.
За 3 года работы масляной печки на отработке ☝️труба выхлопа диаметром 120 мм.забилась сажей полностью так что пришлось менять (как камень)и в мастерской стоял постоянно смрад приходилось регулярно проветривать.и перейти на дровяную печь .
Да, спасибо за вашу точку зрения и то, что вы испытали. Да, это правда, что если не обращаться с запахом осторожно, это приведет к очень неприятному запаху. Да, если вы используете отдельную комнату для разжигания печи. Она полностью пригодна для вашей работы? Если вы используете эту печь прямо на заводе, вы не почувствуете запаха, верно? Но я не знаю, но я знаю, что у вашей раньше было синее пламя. или не при твоей температуре но у моей печки это Температура может достигать 700 градусов по Цельсию, и после газификации он полностью сгорает, не оставляя ни запаха, ни черной пыли. Даже если вы прокипятите кастрюлю из нержавеющей стали, и она не почернеет, я думаю, что она выгорит весь запах, сэр. . За исключением случаев, когда вы впервые его сжигаете или режете и не можете с этим справиться, запах очень сильный, верно? Удачи и спасибо, что поделились. Хороших выходных.
Значит неправильный режим работы. Если горение нормальное, нет ни запаха, ни дыма. В данном видео печь показана с закрытым контуром горения, при герметичном воздуховоде запаху и дыму взяться неоткуда. Ну а если печь самая простая на саможоге, а-ля труба с дыркой, то конечно. Там всё возможно. И дым в мастерской, потому что тяга плохая и сажа в дымоходе, потому что сгорание неполное. Какого типа печь у вас стояла? Сам сейчас топлюсь дровами, раньше была надувная печь на отработке. Все мои проблемы с той печью от неправильного проектирования.
I built a variation that used no power. Basically I had 4" exhaust pipe with a heater box in the middle. At the bottom I had 1/4" pipe wrapped a few inches from the bottom. Fuel was supplied through this pipe from a tank above regulated by a valve. At the bottom was a catcher basin made with a 5" or 6" section of exhaust pipe. Dripping a bit of fuel in the catcher and lighting it would heat the 1/4" tube wrapped around the 4" pipe. This would create a "steam" jet aimed in the center of the 4" pipe creating an updraft. The box above had baffles inside to direct the heat to it shell. The exhaust out the top of the box could come out the side giving you a hot plate. All the fumes were outside and it was smokeless. The box would get red hot and heat us out of the room. Enclosing the box with an outer box you could vent the air where you want, with or without a fan. I designed this after looking at smudge pots people near me were using. They were very smokey and unregulated. I think mine used far less fuel for the same heat.
Well thank you for watching our video and your suggestions and ideas are great Yes you must be an engineer Yes can you give me where is the design drawing of your kitchen I will make that idea and bring it to all the audience around the world to know your idea and will help people get more value please let us know Thank you
@@lmtn "Yes"! To The "Truth"!!.. The "Word"!! Of "GOD"!!. "No"!!!. "ROMAN"! "Sunday"! "God" Genesis 1:( 14-18) "GOD'S"!!.. "Calendar'!!.. Genesis 2 : (1-3)"'GOD'S"!!..Sabbath"!!.. "NO"!!! "ROMAN" "CALENDAR'S" For "Worship"!... "Not"!.. "AT"! "ALL" FOR "ADAM'! AND "EVE'! "MOSES"! AND "AARON"! The "PROPHETS"! "Even'! for Our "Own"! "Savior"! "YESHUA"!! "LORD"!! OF THE "SABBATH"!! Matthew 12:(8) Mark 2:(27-28) "NO"!. "ROMAN"!. "CALENDAR'S"!. For "Worship"! "AT"! "ALL"! For The "People"! Of "GOD"!! in This End "Time's"! Exodus 12:(1-2) Ezekiel 20:(20) Isaiah 66:(23) John 14:(15) John 15:(10-11) "HONOR"!!.. and "GLORY"!!.. To The "CREATOR"!!.. "GOD"!!.. Revelation 14:(6-12) "Day's"! "Month's"! "Year's"! Exodus 12:(1-2) "Moses"! and "Aaron"! 40"Year's"!.. in Mt. Sinai 40 "Year's"!.. in The "DESERT"! "Land"!.. Of "Egypt"!.. "Receiving"! The ("Mana"!) "Keeping"!.. The 7th Day Of "Rest"!.. The "Sabbath"!!.. Of "Creation"!!.. And "THEY"! "HAVE"! "NO"!!!... "NEED"! Of ANY "Man" "Made" "ROMAN"!?... "Paper"!!?.. "Man" "Made" "Calendar"! Of "ROME"! "False"! "ROMAN"! "Calendar's"! All "United"!!! in "ONE"! 🌎 "ONE"! "World"! "ORDER"! 🌎 "ONE"! "Word"! "RELIGION"! 🌎 In "ONE"! "Man" "Made" 🌎 "CALENDAR"!!! Of "ROME"!!! 📅 "False"! "Friday's" for "Islam" ☪️ "False"! "Christian" "Saturday" ✝️ "False"! "Christian" "Sunday" ✝️ for "False"! "Christianity" ✝️ "False"! "Invented" "God" "False"! "Adoration"!... 2 Corinthians 4:(3-4) The "God" Of This "World"!!! 🌎 "Have"! "blind"!!! "Their's"! "Mind's"! 2 Tesssalonians 2:(1-13) "GOD"!!..Will "Send"!.. "Strong"!... "Delusion"!... "One"! "Delusion"! Of "Many"! "Other's"!... To "Come"!. Daniel 7:(25) "Will"!?... "Try"!?... To "Change". "Time's"!!.. and "GOD'S"!!.."Law"!!.. it is "Blasphemy"!... Lie's"!..."Sin"!... Revelation 20:(13) "They"! "Ware"! "Jughead"! "According"! to Their "Work's"! "Salvation"!?... in "Lie's"!?... Of "Course"!!!... Not"!!!... "Salvation"!? in "Pastor's"!? "Family's"!? "Husband's"!? "Wife"!? "Son's"!? "Daughter's"!? "Neighbor's"!? "Pet's"!? "Totally"!!! "Imaginable"!!! "Irracionable"!!! "Incomprehensible"!!!
Yes thank you for your perspective you can be designed in many different styles Yes and thank you for your comments we will note this part Yes thank you Wish you a happy weekend with your family Please give us more comments We look forward to your work
Yes, thank you for watching our video and leaving a comment. I don't understand what you mean, but a stove like this burns at a temperature of about 400 degrees Celsius, then 1 liter of waste oil will last about 4 to 5 hours. If it's good at 700 degrees Celsius, then 1 liter of oil will burn within two hours, which is what you usually do. Wish you a happy weekend. If you have any questions, please leave a comment below. Thank you.
Anybody remember " SALAMANDA" hearers that used waste oil . You got them going with welding torch on a Winter morning. This works similar. They used to get red hot.
@mjblackam I lived in Austalia 1970s . I ran the Diesel Power Station Port Hedland . Goldsworthy Mineing . Those were the days , Gough Whitlam prime minister. Bob Hawk "When are we having another strike !!". Beer 10$ a box .The place ran on the amber necter.
Vielen Dank für Ihre Komplimente und Ihre mehrdimensionalen Perspektiven. Ja, danke. Ich wünsche Ihnen ein schönes Wochenende und erkläre, ob es in Ihrem Land in Deutschland sehr kalt ist
Судя по струе подачи : конский. У меня печь на 30квт , вдвое меньше струя. И да , дым , который выбивается из воронки подачи - говорит о неуправляемости процесса. Это перелив масла и холодная камера сгорания.
You have also forbidden nuclear energy. The most clean energy. And also forbidden cheap energy from russia. So you can say you have forbidden Germany a future.
Это совсем не просто сделать, но главное: А что если электричество вырубят? Есть масса дизайнов, где масло горит без подачи воздуха. Но, в любом случае - Браво!
Спасибо, что посмотрели наше видео и задали вопросы. Да, сэр, его слабость в том, что без подачи кислорода он не будет сильно гореть, без синего пламени он все равно горит, но в нем много комаров и дыма, что очень опасно, сэр. Спасибо за ваше письмо. Вопрос. Есть ли у вас лучший способ? Пожалуйста, покажите мне. Большое спасибо.
@@lmtn За последние годы, на просторах интернета видел массу различных идей. Возмпжно кпд не у всех одинаковый, но видел печь на отработанном масле для гаража, даже с выхлопом, и это очень важно, так как дышать мы все хотим. Помню пару идей, одна из автомобильных дисков(железных само собой), а вторая из старого баллона от пропана. Они не такие компактные, но рабочие. Ещё видел оборгеватель для маленького дома, там вообще, он ещё меньше вашего и идея заключается в отрожателе. Там парень использует тоненький металл, то ли медь, либо какую-то нержавейку, но зеркальную. Я бы нашёл и скинул, но площадка удаляет ссылки, так что сами поищите.
Das ist ein wichtiger Punkt! Abgase wie CO und andere schädliche Stoffe können gefährlich sein. Es ist wichtig, eine gute Belüftung und ggf. eine Abgasreinigung zu haben, um sicher zu arbeiten.
Oh no, that sounds like a series of unfortunate events! Hopefully things turn around soon. Remember, it's always good to keep a positive mindset, even when things get tough.
Why can’t you just be happy for someone else who made something have you done a tutorial for you tube or are you just a keyboard warrior who hate on people who actually teach others how to do different things
@RobertMorris-l3l Try doing structural and lasting welds like this video shows you. You'll see how is doesn't hold or last very long. You obviously have no idea what makes a good weld.
Kabayan..magandang araw...bilib ako sa mga gawa mo lalo na u g nsa video n ito ung may mga bilog sa ibabaw...pde kea ako mka request ng ganito sayu for the right price.Thank you kabayan
Look nice...I would be curious to know, if you had the air quality tested coming off the heat of the fire...would it be safe? Or would it contain harmful fumes produced from the chemicals and additives to the origional oil for vehicles?
How do people add a water section to these and make them into rocket heaters or whatever? Is the water in those versions converted into hydrogen and oxygen to make them burn hotter? 🤔 This would be a nice add-on for the waste oil burner wouldn't it❓
Probably 1 in a billion people will ever desire to do this let alone have the ability or resources.. LOL THOUGH crazy this shit gets 10 mil views .. Can you imagine if people had the time desire resources welding abilities or more? There would be these everywhere huh? DOUBTFUL. :D - TROLLING OUT
It's wonderful when the whole environment where the heater is to be used, is going to stink. The odor of burned oil is something which the neighbourhood surely appreciates. 👍
You're right-burning oil can produce a strong, often unpleasant odor, which isn't ideal for the surrounding area. It's important to make sure that the exhaust is vented properly and that the system is well-maintained to reduce the impact of those fumes. A good filtration system or a better venting solution might help, but it does take some effort to manage. Have you considered any modifications to minimize the smell, or do you just embrace it as part of the process?
Freut mich, dass dir das Video gefallen hat! Der Ölofen mit extra Gebläse und coolem Design ist wirklich eine effektive und praktische Lösung. Danke für das positive Feedback! 😊
При работе агрегата, автор тщательно скрывает - что стоит на том конце подачи 😀уж не добрый ли газбалон, а то огонь больше чем-то напоминает метан-пропан чем вонючую и дымящую отработку. Ловкость рук и миллион просмотров 😅
Хаха, возможно, автор действительно что-то скрывает! 😉 Иногда в видео используют такие хитрые приёмы для эффектности. Как вы думаете, какие ещё способы можно использовать для улучшения работы агрегатов, чтобы они были безопаснее и эффективнее?
waste oil heating stove mini 3 in 1 ! Millions of people do not know this knowledge
th-cam.com/video/B6jvvZkD3P0/w-d-xo.html
its been used in philippines 2 years ago as stove
after 25 years I have had to say goodbye to my yard and workshop, I live on a boat so have had to get rid / pass on a lot of tools from lathes to engine cranes and 5 trucks plus a live on bus ranging in physical weight from 3000kgs to 7500kgs, watching videos like this makes me happy to see people still showing how to make things.
I have a waste fuel heater and it works well, no external flame so clean water free hot air.
Keeps me toasty on the cold days / nights.
It sounds like you've made quite a big change in your life! It's great that you found a way to stay warm with your waste fuel heater. Best of luck with your boat life and keep enjoying those creative videos!
Iv been thinking about doing that ,buying a pontoon, and building a styrfoam shach on it and sail away . and I want to use waist oil to produce hot water, heat and electricity .
Like a little 10 foot boat 😅
@@andrewreed7607 ya and Im going to make the top where I can walk on it . 0 rent o insurance o taxes move to any water frount prop .
dont tell the homeless
عمل رائع شكرا لك❤️
احب ان اضيف لك شيئا
تستطيع ان تضع بايب نحاس لولبي حول حجرة الاحتراق ويمر الماء من خلالها بدائره مغلقه سوف يصبح لدينا ماء ساخن للاستخدام بنفس الوقت👍
اشكرك على هذا المجهود الرائع انت تستحق المتابعه والنشر😘
شكرًا لك على هذه الفكرة الرائعة! استخدام بايب نحاس لولبي حول حجرة الاحتراق لتسخين الماء فكرة مبتكرة جدًا. سعيد بأنك استفدت وأتمنى لك المزيد من النجاح! 😊
Very cool, the Buick Dealership
I worked at used a waste oil
heater to warm the shop in the
winter, all of the used oil and gasoline from oil and fuel filter
changes went into a 100 gallon tank thru the spring and summer and was full by winter!! At the start of winter we would clean the burner and light it, with the 10 overhead doors being opened thru the day to bring cars in and out of the shop it was a cheap way to heat!!!
I worked for a towing company/scrap yard and they used a waste oil furnace for the shop. It worked quite well. It did have some problems occasionally. I went in on a Saturday to find the whole shop filled with smoke cause the heat exchanger cracked. It was missing paint off the side of the furnace housing because it got oil with too much gasoline in it one time and it got extremely hot.
@juliogonzo2718 With all of us
Mechanics opening and closing the
Garage doors all day it would have
cost a fortune heating with natural
gas, plus it also heated the body
shop too!!! We did have natural gas
heaters in the service lanes but they
were efficient enough for that use!!!
And they paid big bucks for it because theirs actually worked, unlike this fake shit.
@HueToobBlows What makes you say its fake? I'd have to see this one in person to 100% believe it works, but I don't see why it wouldn't.
Yes thank you for watching our video it's great where you are also using a waste oil heater right? Yes waste oil heating water costs extremely low and to make one directly is not worth much money and waste oil is something that is almost available right? Yes when done correctly it has a very high temperature of up to 700 degrees Celsius and there is no black smoke so when it enters the air when the temperature is high when it is chemically it will burn completely creating a blue flame like gas Thank you for giving us positive words do you have any suggestions for us to do better Please let us know We will improve the product further to contribute to bringing more value and benefits to audiences around the world Thank you
Well done....Remember safety is paramount....Can't be used indoors as products of combustion are toxic and cause death...Can only be used in a well ventilated area...that's with any combustion process....recommend using a stainless steel flue vented directly outside of the heating environment so you get the BTU heat from the flue as well.Stay safe.
Great advice! Safety is crucial-ventilating properly and using a stainless steel flue ensures safe combustion and maximizes heat efficiency. Stay safe!
Welp, guess everyone that uses natural gas for heat can throw that in the garbage.
@@cadevaughn7596 you still need electricity for natural gas, no
@@mariobrus9603no you don’t. Electricity is only for igniter. U can use a match
Yea i wish my hvac guy would have told me i cant burn anything in the house. Gas range is gone too.@cadevaughn7596
Love it makes me think of cooking a pot of stew or beans on top of our kerosene heaters back in the day! Enjoyed thanks for sharing God Bless u and urs!
Remember the days of cooking or parking on a kerosene stove, so cozy. Thank you, God bless you!
This is true ha. However I wouldn't cook anything on this. Nor would I want that venting inside a living space or workspace. Old/used motor oil contains some pretty narley chemicals and if you I breath it long enough can cause some pretty bad health issues.
@@joshuak2197your gonna die anyway, what you plan on living until you’re 200yrs old or something? Give me a break
🇮🇶From Iraq, you are a man worthy of respect
Thank you so much! I deeply appreciate your respect and support. Greetings to Iraq! 🇮🇶
What?
"A man worthy of respect"
What?
@@MB5rider81Seems like our friend from Iraq has a better grasp of the English language than you do.
I totally agree with a post further down. It’s consuming oxygen and the fumes it’s producing. This should only be used in a well ventilated area or outside. The flame 🔥 color is correct for an oil / waste oil burner. I had a commercial build waste oil furnace in my garage. I loved it basically free heat other than the tiny bit of electricity ⚡️ for the fan and tiny pump for the oil. It was 60,000 BTUs on a continuous run no thermostat. Go out start it , have breakfast and then the garage would be starting to warm up. I did a lot of driving and a lot of oil changes, so it worked out perfectly. The furnace would burn 1/2 gallons per hour or roughly 2.7 liters.
That's a minimum of 250 gallons per winter. That would be over 20 oil changes on a semi engine. It would take several semis annual oil changes to supply one such heater.
That is why you let people who live around you know that they can dispose of their waste oil for free by just leaving it at your facility. There is a place near me that allows anyone to leave waste oil with them, and I have seen the setup they have to filter and burn it, very neat and useful if done properly and safely.
@@hunterd78 Oil is used for asphalt and asphalt sealing.
@@Absaalookemensch
Hi, you are correct if I ran continuously. However this was in my garage. Also ran every weekend and maybe a few nights during the week. I was changing oil in my daily driver, my girlfriends, once in a while in 3 other cars and I was racing PRO Rally at the time. The rally car got the most oil changes. Especially when something bounced up and destroyed the oil filter. Very quick end to that race.
Okay, what does that have to do with anything?
The skill and knowledge is fantastic. Very enjoyable to watch😊
Все хорошо и красиво но есть один минус это нет дымохода. Такая штука рано или поздно выжгет кислород из воздуха и засерет его продуктами сгорания этой отработки. Дым хоть и не видимый но запах по любому есть.
Хорошо
Такую горелку только на улице можно разжигать, иначе можно угореть. Вообще идея хорошая но нужно дорабатывать.
А чем масляный электрообогреветель хуже то ?
Походу он и дешевле будет в эксплуатации, и экологичней.
Эта байда хороша где ляктричества нет и мазуту тырить можна. А так то буржуйка понадёжней. И омлетик пригатовить с грогом, и жги чё под руку попадёт. От соседскога забора, до отходов мебельнога канцерна.
LP LP8@@АдминСтимович
есть еще один огромный минус. это привязка к электричеству
Breathe deeply for greatest effect. 😮
Чорний гумор , але справедливий.
Perfect for a Yurt.
Lanair makes a waste oil burning/ forced air heater, that is EPA compliant.
And YES, you can burn dirty oil, cleanly, as long as you preheat the chamber first.
"Yes"! To The "Truth"!!..
The "Word"!! Of "GOD"!!.
"No"!!!. "ROMAN"! "Sunday"! "God"
Genesis 1:( 14-18)
"GOD'S"!!.. "Calendar'!!..
Genesis 2 : (1-3)"'GOD'S"!!..Sabbath"!!..
"NO"!!! "ROMAN" "CALENDAR'S"
For "Worship"!... "Not"!..
"AT"! "ALL"
FOR
"ADAM'! AND "EVE'!
"MOSES"! AND "AARON"!
The "PROPHETS"!
"Even'! for Our "Own"! "Savior"!
"YESHUA"!!
"LORD"!! OF THE "SABBATH"!!
Matthew 12:(8) Mark 2:(27-28)
"NO"!. "ROMAN"!. "CALENDAR'S"!.
For "Worship"! "AT"! "ALL"!
For The "People"! Of "GOD"!!
in This End "Time's"!
Exodus 12:(1-2)
Ezekiel 20:(20)
Isaiah 66:(23)
John 14:(15) John 15:(10-11)
"HONOR"!!.. and "GLORY"!!..
To The "CREATOR"!!.. "GOD"!!..
Revelation 14:(6-12)
"Day's"! "Month's"! "Year's"!
Exodus 12:(1-2)
"Moses"! and "Aaron"!
40"Year's"!..
in Mt. Sinai 40 "Year's"!..
in The "DESERT"!
"Land"!.. Of "Egypt"!..
"Receiving"! The ("Mana"!)
"Keeping"!.. The 7th Day Of "Rest"!..
The "Sabbath"!!.. Of "Creation"!!..
And "THEY"! "HAVE"! "NO"!!!... "NEED"! Of ANY "Man" "Made" "ROMAN"!?... "Paper"!!?.. "Man" "Made" "Calendar"! Of "ROME"!
"False"! "ROMAN"! "Calendar's"!
All "United"!!! in "ONE"! 🌎
"ONE"! "World"! "ORDER"! 🌎
"ONE"! "Word"! "RELIGION"! 🌎
In "ONE"! "Man" "Made" 🌎
"CALENDAR"!!! Of "ROME"!!! 📅
"False"! "Friday's" for "Islam" ☪️
"False"! "Christian" "Saturday" ✝️
"False"! "Christian" "Sunday" ✝️
for "False"! "Christianity" ✝️
"False"! "Invented" "God"
"False"! "Adoration"!...
2 Corinthians 4:(3-4)
The "God" Of This "World"!!! 🌎
"Have"! "blind"!!! "Their's"! "Mind's"!
2 Tesssalonians 2:(1-13)
"GOD"!!..Will "Send"!..
"Strong"!... "Delusion"!...
"One"! "Delusion"! Of "Many"! "Other's"!... To "Come"!.
Daniel 7:(25)
"Will"!?... "Try"!?... To "Change".
"Time's"!!.. and "GOD'S"!!.."Law"!!..
it is "Blasphemy"!... Lie's"!..."Sin"!...
Revelation 20:(13)
"They"! "Ware"! "Jughead"!
"According"! to Their "Work's"!
"Salvation"!?... in "Lie's"!?...
Of "Course"!!!... Not"!!!...
"Salvation"!?
in
"Pastor's"!?
"Family's"!?
"Husband's"!?
"Wife"!?
"Son's"!?
"Daughter's"!?
"Neighbor's"!?
"Pet's"!?
"Totally"!!!
"Imaginable"!!!
"Irracionable"!!!
"Incomprehensible"!!!
@@PapaSnuffy love the spirit Papa Snuffy! Have a snort and remain calm. it is always later than one thinks! Whatever doesn't kill you makes you stronger they say.
I like it. Its burning efficient with the blower fan so should be minimal fumes and separating the burning chamber from the outer hot air chamber just completes it. Works just like a diesel heater so using it as a heater should be good so long as your welds dont have holes😉
Glad you like it! The blower fan makes it efficient, and separating chambers ensures better performance. Just keep those welds tight! 😉
So you are burning waste oil so cleanly that you can do it indoors without a flue or hood venting outside?
@@dakotachristianson3756 Not possible, carbon monoxide would still be a concern. I think the stove would have to operate outside with the secondary heat going into a structure.
@@dakotachristianson3756 even though he didn't make it very clear, I'm pretty sure the stove part goes on the outside of the building and the flexible duct that he showed gets routed to blow the hot air inside the building.
@@josephoxenham6142if your not familiar with a properly set up waste oil burning stove than just say so lmfao. You have not the slightest clue of what your talking about. I've been around them for years and never a health concern one set up right they are very efficient. the epa approves and encourages there use, as it is safer to convert/burn a potentially hazardous waste onsite
Canada!! Great video.. You make your own Primus Stove. I'd never have thought of this. Thank you.
You're welcome! Glad you enjoyed the video. It's always fun to discover creative ideas like making your own stove!
Awesome build. I’m thinking of building one of these, thank you for the video.
I am not the one to put down anyone’s hard work.
I’m just wondering about the tack welding technique. Just a suggestion; If you play around with your tuning knobs, adjust your amperage down and adjust the wire feed comparing how fast the wire melts per amp temperature, you could get a continuous flow to form a solid welds with better penetration instead of tack welds.
I believe the tack welding method reduces warpage when welding sheet steel.
@@genebartle7715 Pulse dime, cool, pulse dime, cool, does prevent material warping, at expense of less penetration, trade-off
@@AaronSchwarz42 Muliptle tacks, alternating sides in a pie cut pattern similar to how you tighten lug nuts, will prevent the warping. The amount of tacks will vary depending on size. Then follow up with multiple good penetrating beads in a similar pattern eventually connecting all your clean beads (lay some dimes). Will most importantly penetrate, and prevent any pinhole leaks as well, without warping. Finish by chipping, grinding, and polishing smooth.
Thanks for the suggestion! Adjusting the amperage and wire feed speed for better penetration and continuous flow is a great idea for improving weld quality. I'll definitely give it a try!
I'm really impressed that you managed to (mostly) hide the gas pipe.
So, it's using gas and not oil?
Wait! You mean a couple scraps of burning paper won't light motor oil? Shocked, I tell you, shocked! 😆😆😆
@@esra_erimez It's false, he's using Gas. The oil almost doesn't burn, if you blow it it goes out. Fire can be seen coming out of the center blower inside the oil container. If it blows air it should not ignite, only stoke the fire in another place, but flame comes out because it blows Gas.
@@928hparedes Thanks!
Thank you for recording and posting this valuable educational video.
You're very welcome! I'm glad you found the video helpful. Thank you for your kind words! 😊
Video này hay quá! Thật tiếc nếu như hàng triệu người ngoài kia không biết những điều này cho mùa đông.
Thanks for your feedback on our video, you must have watched 2/3 of the video, which part is your favorite?
you're a friggin tool...
Здоровее будут!
Отличная штука, чтобы устроить пожар или надышаться парами. А когда отработка попадет с водой, будет классный фонтан из кипящего и горящего масла!😂👍
Главная причина почему это полная херня, если забыть про токсичность продуктов горения - это то что отработка на самом деле совсем не бесплатная и не дешевая (особенно в случае если все начнут использовать ее как топливо). Если где-то есть шаровой источник, например, у работника автосервиса, то даже там для нормального отопления может не хватить. Проще и дешевле бензином отапливаться или дизельным топливом.
Воду специально добавляют в топку, для поднятия температуры , экономии и экологии... Попугаи слышат звон да не знают где он😢😢😢
@@РыбакРыбака-з3ы может где-то и добавляют воду в промышленных печах, но не в таких кастрюлях с кипящим маслом. Я полно историй пожаров знаю, когда отработка не отстоянная пыхает и превращается вся печь в фонтан из горящего масла. Причем у знакомого на производстве бахает даже промышленная печь так что стены трясутся, когда вода попадает. Можешь со мной не спорить, я сам эжекторную печь на отработке делал. Вонища от нее как в плохой котельной, учесть что у меня в трубу тянуло, а не как тут просто кастрюля с маслом. В итоге на дровяной котел ее переделал.
И как писали выше цена на отработку подскочила, раньше за так нальют, где хочешь, а теперь 5-7р. за литр. Так что звон слышал ты, а я эту тему знаю.
@@РыбакРыбака-з3ы Где конкретно добавляют, примеры? Если те доб***бы с вечным поленом, можешь не отвечать.
Вы большой мастер. И фильм снят правильно, все операции по очереди. Респект!
Спасибо большое! Рад, что вам понравилось. Всегда стараюсь делать все по порядку и качественно!
Best design I've seen yet. Not sure I like the way you have the drip setup but that's easily changed. Other then the drip and making a tweak to the exhaust I'm definitely building this bad boy
Thank you! I’m glad you like the design. The drip setup and exhaust can definitely be tweaked to suit your preferences. Feel free to make adjustments as you build it!
my friend had a big one of these in his big workshop I thought it was fantastic and the large area was definitely not cold even with the bay door open all day
페유는 불법 입니다
I seldom see any concern expressed about the heavy metal contamination in waste oil when burned. There is a great centerfugal oil extraction method that removes some of it but the only way I can imagine to be really sure is to "crack" it all over again and of course that takes quite a bit of heat too. How can you win?
You raise an important concern regarding the heavy metal contamination in waste oil. When burning waste oil, especially from automotive or industrial sources, it can contain a variety of harmful contaminants, including heavy metals (like lead, cadmium, and chromium), as well as other toxic byproducts that may be released into the air when burned.
While centrifugal oil extraction can help remove some contaminants by separating out solid particles and some heavier impurities, it doesn't fully address the issue of hazardous metals that may still be present in the oil. To fully eliminate these contaminants, you would need a more complex process, such as "cracking" or refining the oil back to a purer state, which would require significant heat and specialized equipment. This process, however, is energy-intensive and costly, which could make it impractical for most DIY or home heating systems.
To reduce the risks of burning waste oil, here are some possible solutions:
Filtration: Advanced filtration systems could help remove larger contaminants, but they won't fully eliminate heavy metals or some of the finer impurities. Multi-stage filtration, combining mechanical, chemical, and carbon filters, can improve oil purity, but the risk of heavy metals remains.
Exhaust Scrubbing: Installing a scrubber or an afterburner system in the exhaust could help trap or neutralize harmful emissions, including particulate matter and toxic fumes. This would help reduce the impact of burning contaminated oil on air quality.
Pre-Treatment of the Oil: If you plan to burn waste oil regularly, you could look into oil refining or cracking methods that break down the contaminants before combustion. This might involve heating the oil in controlled conditions, but again, it would require a lot of energy and specialized equipment.
Monitoring and Testing: Periodically testing the oil for contaminant levels (especially heavy metals) could help you understand its quality and whether it's safe to burn. You could also monitor the emissions to ensure they stay within safe levels.
In summary, while it is possible to burn waste oil, doing so safely requires a multi-step approach to reduce contamination. The best way to win is to balance efficiency, safety, and environmental impact. Using clean or filtered oil, or even considering alternative fuels, could be an effective compromise for home heating systems.
@@lmtnThe combustion of used motor vehicle oils does entail the problem of heavy metals. Many heavy metals can be filtered out via fiber filtration and centrifuge equipment as I have at my shop. On the exhaust end, you can use the tendency of heavy metals to form sulfides to create a reactive filter - but this is outside the capability of a home shop. A cooling tower with soot traps might be more feasible if visibility is not an issue.
@@lmtn ai response?
Очень хотелось бы такую горелку для твёрдо толевного котла, только без принудительной подачи воздуха и так что оно не ебануло(не взорвалось)
@@lucast89forsure
Yes everything is fantastic except the smell. It is almost impossible to operate it indoors.The one shown at the end of the video, working in a separate area is the best. Congratulations to the manufacturer!
Thank you for your comment! I agree, the smell can be a challenge indoors. The separate area setup definitely seems like a smarter choice. Appreciate your feedback and support!
You should catch up the air from outside. Otherwise, the heated air you blow into the next room will be the polutet Air from the burner! BTW In europe, the greens will hit you to death doing this. 😂😂
@@kickacopsassdaily yeah well fuck the greens. Much love from Germany
He could place it outside build a heat accumulator blow hot air in
Great video, you are very good with your tools, and now I know what I'm going to do with my waste oil tank. I have a garage and a shop that both need heating and I'm tired of buying propane 👌 I was going to build a waste oil forge a while back but ended up buying a pre-made propane one, so ive just been filling my oil tank every oil change. This would be a great addition to the shop and garage 👌 and keep my tank from getting full to boot
I appreciate your great work, you got a new subscriber here buddy 👍
Thank you so much for the kind words and support! I'm glad the video inspired you. A waste oil heater is a great way to repurpose your old oil while heating your shop and garage efficiently. Best of luck with your build, and welcome to the channel! Appreciate you subscribing! 👍
Sehr Gesund die Abgase von der verbrennung des Altöls... 😮
Thank you for reminding us so much Yes, the exhaust from burning oil also has a lot of toxic gases, right? You must be a professor Yes We will try to burn it far away from the area alone, just insulating it inside, is that okay? Yes, please give your opinions and suggestions Thank you
Ob da wirklich mehr relevante Schafstoffe drin sind? Die Verbrennung sieht schon sauber aus.
Они полезны несколько минут ,потом резкая потеря сознания и смерть.
@@johannesmeyer-dunker6044 Wie alle heutige Abgase vom Autos. "Transparent" bedeutet nicht gesund.
@@johannesmeyer-dunker6044 das ist wissenschaftlich erwiesen, nur weil du es mit bloßen Augen nicht siehst, heißt es nicht, dass sie nicht da sind. ES IST AUF KEINEN FALL GESUND ALTÖL ZU VERBRENNEN
Молодец мужик, спасибо за полный обзор 💪💪💪
Спасибо большое! Рад, что обзор оказался полезным. Ваши слова вдохновляют! 💪💪💪
Very good!
Excellent video. Thanks very much from SLMC🔥 .
Cheers 🍻
Thank you! I'm glad you enjoyed the video. Cheers to you as well from SLMC! 🍻🔥
In Soviet union we used and still using different kinds of waste oil heaters in garages and warehouses in rural areas. Most of them are handmade. So it's very economical.
Yeah, and the oil comes from dead bodies, so it's free. Just gotta point the finger at a neighbor and you'll have his whole family, oops, I mean a whole months worth of "waste oil".
@@deucedeuce1572nah. That's how the west gets it's oil, not Russia.
@deucedeuce1572 wtf?
@@deucedeuce1572 UrAFu(kin Ja(ka$$
قمة الإبداع والتميز،
إحترامى وتقديرى لحضرتك،
فضلا الموسيقى مزعجه، 🌹🌹🇪🇬
Süper ötesi, muazzam güzel, harikulade :))
We made a version of that. We made a combustion chamber and put it inside an old wood stove. Had a blower tube coming in the back. And I forget what we used for the oil tank but we would use air pressure to feed the oil. Used it many years. Before the boss got a propane heater.
Yes thank you for your sharing and receiving our videos Yes sir do you have any techniques to do better please leave us a comment and your feedback Thank you very much in I will follow your ideas to be able to improve better to bring more value to viewers Wish you a happy weekend
I made one at home using a steak knife, butane torch and a nail file.. true diy at home project for the entire family
That sounds risky! It's important to prioritize safety and use proper tools for any DIY project.
@@lmtn - You mean I can't make this with a milk carton and some sticky back plastic?
Главное чтоб вода из кастрюльки не булькнула на печку, а так да, шедевр! Браво.
Спасибо за комментарий! 😄 Ты прав, важно, чтобы вода не попадала на печку - безопасность всегда на первом месте.
Excelente trabajo, muy bien estructurado...me gusto y lo pondre en practica...con ese aceite usado, se ahorra el gas butano en la cocina...me gusta bro...👍...
¡Muchas gracias! Me alegra que te haya gustado. Usar aceite usado para ahorrar gas es una idea genial. ¡Éxito! 👍
Os engañan como a chinos, ha conectado gas de una bombona donde tenía el ventilador.
Es falso, esta usando Gas. El aceite casi no arde, si lo soplas se apaga. Se puede ver fuego saliendo del soplador central dentro del recipiente de aceite. Si sopla aire no debería prender, solo avivar el fuego en otro lugar, pero sale llama porque insufla Gas.
Супер, золотые руки. 👍
And black lungs...
Fake, totally fucking fake. And you're an idiot if you believe it.
Awesome, thanks for the video and the measurements 👍
Fire it up in the garage (well ventilated) a great Idea to have it in case of an emergency.
You're welcome! Glad you liked the video and measurements. A well-ventilated garage is perfect for safety. It's always a good idea to be prepared for emergencies. Stay safe and enjoy! 👍
Great work and great outcome. FYI, those overlapping tack welds will have much poorer penetration than a steady bead at the same setting.
Thanks for the feedback! That’s a great point about the welds. Do you have tips for improving steady bead welding techniques?
@@lmtn Yes, practice. Practice and make sure you are comfortable. Anchor your torch hand on your free hand and make sure you can do the whole weld without repositioning. There are youtube videos on the subject. Refine your search words.
Praktisch auch, dass gleichzeitig die Bude mit Altölabgasen verpestet ist 😎
Vielen Dank für Ihre grundlegende Sichtweise. Ich hoffe, dass unser Edelstahltransformator nicht schwarz wird. Ich wusste nicht, dass er eine so hohe Verschmutzung aufweist . Nein, Sir. Ja, vielen Dank, bitte teilen Sie mir Ihre eigenen Vorschläge mit. Vielen Dank
@@lmtnweist er auch nicht, weil ihr ihn mit Gas betreibt
Wo kann man sowas kaufen?
Die Anlage steht draussen und bläsed warme Luft in die Bude. Ich glaube auch, dass da kein Geruch ensteht bei den hohen Temperaturen. Das Teil ist nicht schlimmer als die alten Heizölöfen meiner Eltern und Großeltern. Fragt sich aber nur, wo kriegt man so viel Altöl her, um einen ganzen Winter zu heizen.
@@mikethespike7579 Im Hafen!
Who welds like that with a MIG 🙄
No Trained Welder I Say
I Got 17yrs You Lose Your Job You Think Tack Welds Are The Same As Diameter Welding
Fucking hate welder know it alls Jesus Christ you people are insufferable. Been in the trades going on 30 years. There is no one worse than a “proud” welder
My 12yo daughter welds better than that.
I'd say he's just showing everyone there interested the how to. I'll never understand why people go after the little shit instead of just being grateful to learn something that may indeed help one day@@americanandroid9952
I'm no pro but, experimenting with brass flux coated rods & MiG, the MiG laid down a better weld on brass than the brass in the MMA stick wand. Although today messing around with my 3-in-1 combo welding toy I put some tungsten in the MMA wand & went over welds I put with brass rods wrapped by hand with MiG wire & actually got welds to stick & hold to cast iron. Just an ace of trades playing around with a skill that is on the road to perfection. Any suggestions or helpful tips are appreciated.
Ingenious, every home should have one.
They have been around for years .They used them in junkyards in the colder climates and used oil out of junked cars to put in them . They were about 1 meter in height .
I remember an auction house in Invercargill had one. It heated up the whole room really quickly.
@@janecapon2337we still have one in the workshop, works well, gives out great heat
Had one in a 4 bay repair shop i worked at in Albuquerque about 10 years ago, worked amazing and was basically free heat. Probably still have it haha
Exactly! These stoves have been around for a while, especially in colder climates, repurposing used oil from junked cars for heat.
That’s awesome! It’s great how effective and cost-efficient those stoves can be, especially in a busy repair shop environment.
Awesome JOB !
thanks for your compliments
have a nice day
طريقة ممتازة للموت باول اوكسيد الكاربون ...
Excelente idea y ayuda para usar , felicidades por su gran trabajo desde Saltillo coahuila
¡Gracias! ¿Has considerado alguna vez hacer algo similar con otros materiales reciclados? Sería interesante saber tu opinión.
So this gives me an idea, could you adapt thus as the heat source for a clothes dryer? Just the hot air, so the clothing doesn't smell like waste oil.
Major fire hazard even best case scenario
How would you regulate the heat?
Maybe a hair drier?
@@jjb1974 umm, maybe add air vents along the pipe until you get a constant temp for drying? Or blower could cycle with the temp sensor? If you utilize the blower from the dryer as the blower for the heat source you would have everything you need i think.
@@captainlandyacht1328 Makes sense.
За 3 года работы масляной печки на отработке ☝️труба выхлопа диаметром 120 мм.забилась сажей полностью так что пришлось менять (как камень)и в мастерской стоял постоянно смрад приходилось регулярно проветривать.и перейти на дровяную печь .
Да, спасибо за вашу точку зрения и то, что вы испытали. Да, это правда, что если не обращаться с запахом осторожно, это приведет к очень неприятному запаху. Да, если вы используете отдельную комнату для разжигания печи. Она полностью пригодна для вашей работы? Если вы используете эту печь прямо на заводе, вы не почувствуете запаха, верно? Но я не знаю, но я знаю, что у вашей раньше было синее пламя. или не при твоей температуре но у моей печки это Температура может достигать 700 градусов по Цельсию, и после газификации он полностью сгорает, не оставляя ни запаха, ни черной пыли. Даже если вы прокипятите кастрюлю из нержавеющей стали, и она не почернеет, я думаю, что она выгорит весь запах, сэр. . За исключением случаев, когда вы впервые его сжигаете или режете и не можете с этим справиться, запах очень сильный, верно? Удачи и спасибо, что поделились. Хороших выходных.
Значит неправильный режим работы. Если горение нормальное, нет ни запаха, ни дыма. В данном видео печь показана с закрытым контуром горения, при герметичном воздуховоде запаху и дыму взяться неоткуда. Ну а если печь самая простая на саможоге, а-ля труба с дыркой, то конечно. Там всё возможно. И дым в мастерской, потому что тяга плохая и сажа в дымоходе, потому что сгорание неполное. Какого типа печь у вас стояла? Сам сейчас топлюсь дровами, раньше была надувная печь на отработке. Все мои проблемы с той печью от неправильного проектирования.
30 лет топлю в Сибири , котельная отдельно и неразу трубу не чистил... Дружи с головой😢
I built a variation that used no power. Basically I had 4" exhaust pipe with a heater box in the middle. At the bottom I had 1/4" pipe wrapped a few inches from the bottom. Fuel was supplied through this pipe from a tank above regulated by a valve. At the bottom was a catcher basin made with a 5" or 6" section of exhaust pipe. Dripping a bit of fuel in the catcher and lighting it would heat the 1/4" tube wrapped around the 4" pipe. This would create a "steam" jet aimed in the center of the 4" pipe creating an updraft. The box above had baffles inside to direct the heat to it shell. The exhaust out the top of the box could come out the side giving you a hot plate. All the fumes were outside and it was smokeless. The box would get red hot and heat us out of the room. Enclosing the box with an outer box you could vent the air where you want, with or without a fan. I designed this after looking at smudge pots people near me were using. They were very smokey and unregulated. I think mine used far less fuel for the same heat.
Well thank you for watching our video and your suggestions and ideas are great Yes you must be an engineer Yes can you give me where is the design drawing of your kitchen I will make that idea and bring it to all the audience around the world to know your idea and will help people get more value please let us know Thank you
@@lmtn
"Yes"! To The "Truth"!!..
The "Word"!! Of "GOD"!!.
"No"!!!. "ROMAN"! "Sunday"! "God"
Genesis 1:( 14-18)
"GOD'S"!!.. "Calendar'!!..
Genesis 2 : (1-3)"'GOD'S"!!..Sabbath"!!..
"NO"!!! "ROMAN" "CALENDAR'S"
For "Worship"!... "Not"!..
"AT"! "ALL"
FOR
"ADAM'! AND "EVE'!
"MOSES"! AND "AARON"!
The "PROPHETS"!
"Even'! for Our "Own"! "Savior"!
"YESHUA"!!
"LORD"!! OF THE "SABBATH"!!
Matthew 12:(8) Mark 2:(27-28)
"NO"!. "ROMAN"!. "CALENDAR'S"!.
For "Worship"! "AT"! "ALL"!
For The "People"! Of "GOD"!!
in This End "Time's"!
Exodus 12:(1-2)
Ezekiel 20:(20)
Isaiah 66:(23)
John 14:(15) John 15:(10-11)
"HONOR"!!.. and "GLORY"!!..
To The "CREATOR"!!.. "GOD"!!..
Revelation 14:(6-12)
"Day's"! "Month's"! "Year's"!
Exodus 12:(1-2)
"Moses"! and "Aaron"!
40"Year's"!..
in Mt. Sinai 40 "Year's"!..
in The "DESERT"!
"Land"!.. Of "Egypt"!..
"Receiving"! The ("Mana"!)
"Keeping"!.. The 7th Day Of "Rest"!..
The "Sabbath"!!.. Of "Creation"!!..
And "THEY"! "HAVE"! "NO"!!!... "NEED"! Of ANY "Man" "Made" "ROMAN"!?... "Paper"!!?.. "Man" "Made" "Calendar"! Of "ROME"!
"False"! "ROMAN"! "Calendar's"!
All "United"!!! in "ONE"! 🌎
"ONE"! "World"! "ORDER"! 🌎
"ONE"! "Word"! "RELIGION"! 🌎
In "ONE"! "Man" "Made" 🌎
"CALENDAR"!!! Of "ROME"!!! 📅
"False"! "Friday's" for "Islam" ☪️
"False"! "Christian" "Saturday" ✝️
"False"! "Christian" "Sunday" ✝️
for "False"! "Christianity" ✝️
"False"! "Invented" "God"
"False"! "Adoration"!...
2 Corinthians 4:(3-4)
The "God" Of This "World"!!! 🌎
"Have"! "blind"!!! "Their's"! "Mind's"!
2 Tesssalonians 2:(1-13)
"GOD"!!..Will "Send"!..
"Strong"!... "Delusion"!...
"One"! "Delusion"! Of "Many"! "Other's"!... To "Come"!.
Daniel 7:(25)
"Will"!?... "Try"!?... To "Change".
"Time's"!!.. and "GOD'S"!!.."Law"!!..
it is "Blasphemy"!... Lie's"!..."Sin"!...
Revelation 20:(13)
"They"! "Ware"! "Jughead"!
"According"! to Their "Work's"!
"Salvation"!?... in "Lie's"!?...
Of "Course"!!!... Not"!!!...
"Salvation"!?
in
"Pastor's"!?
"Family's"!?
"Husband's"!?
"Wife"!?
"Son's"!?
"Daughter's"!?
"Neighbor's"!?
"Pet's"!?
"Totally"!!!
"Imaginable"!!!
"Irracionable"!!!
"Incomprehensible"!!!
What you’ve described is exactly what I’m looking for, blue flame without a fan/electricity. I’ll give it a shot from your description.
Can you make a video of how you made it ?
Valuable and excellent work
Excellent project. Surely there has to be a better oil feed than dripping from an open faucet? Looks like quite a hazard in that regard.
Yeah, a clear plastic tube could be plumbed in for a few bucks more.
Yes thank you for your perspective you can be designed in many different styles Yes and thank you for your comments we will note this part Yes thank you Wish you a happy weekend with your family Please give us more comments We look forward to your work
great Thanks and your opinion Yes thank you Have a nice weekend
Yes, thank you for watching our video and leaving a comment. I don't understand what you mean, but a stove like this burns at a temperature of about 400 degrees Celsius, then 1 liter of waste oil will last about 4 to 5 hours. If it's good at 700 degrees Celsius, then 1 liter of oil will burn within two hours, which is what you usually do. Wish you a happy weekend. If you have any questions, please leave a comment below. Thank you.
Because everybody has a metal working shop out back, 1% practical.
Don't need a welder. Just standard pipe connections.
Harbor Freight sells everything used in this video, Soyman117.
I thought everyone else owned 4 welders, torches and a plasma cutter too??
@@a.joegevara3519 Alpha men go to Harbor Freight and buy this equipment.
Right
Cool but isn't the air toxic to breath?
Not if there's a exhaust pipe.
@barbarawaggoner8605 oh ok thank you for explaining it👍🏾
The same way the exhaust off a wood stove is. Vent it outside,so simple yet no one gets this.
I should have said exhaust "vent" in this case.!
Ja denke ich auch. Nichts für geschlossene Räume.
Really cool video, i enjoyed watching it. I bought a welder recently and plan to learn to weld. Was that a MIG welder you were using?
Thanks! Yes, it looks like a MIG welder in the video. Good luck with your welding journey-it's a great skill to learn!
Anybody remember " SALAMANDA" hearers that used waste oil . You got them going with welding torch on a Winter morning. This works similar. They used to get red hot.
I remember them, they were around in Australia back in the 70s. Great for outdoor get togethers.
Yep. They were very effective in heating large spaces and they didn't need electricity.
@mjblackam I lived in Austalia 1970s . I ran the Diesel Power Station Port Hedland . Goldsworthy Mineing . Those were the days , Gough Whitlam prime minister. Bob Hawk "When are we having another strike !!". Beer 10$ a box .The place ran on the amber necter.
Und wenn der Schornsteinfeger sieht, der rastet das.
Super Idee!
Vielen Dank für Ihre Komplimente und Ihre mehrdimensionalen Perspektiven. Ja, danke. Ich wünsche Ihnen ein schönes Wochenende und erkläre, ob es in Ihrem Land in Deutschland sehr kalt ist
Интересно какой расход отработки
Судя по струе подачи : конский. У меня печь на 30квт , вдвое меньше струя. И да , дым , который выбивается из воронки подачи - говорит о неуправляемости процесса. Это перелив масла и холодная камера сгорания.
Why does it smell like exhaust in here, you been riding your dirt bike inside again?
Hehehe 😂😂😂😂😂
That's the kind of fire I need to make fried rice.
WoW.. Amazing product... clever job.. ♥♥♥
Here in Germany this is forbidden for at least 35 years.
У вас всё запрещено 😢
You have also forbidden nuclear energy. The most clean energy. And also forbidden cheap energy from russia. So you can say you have forbidden Germany a future.
@@TH-cam_kontot nuclear is far from clean or safe don’t kid yourself
Jebala te nemacka
Alles was nicht ausdrücklich genehmigt ist ist in Deutschland Verboten.
There is a reason why propane is very popular
no need to buy propane if you can change your own oil and have one of those
I like kerosene
What about combustion gases 🧐
Вот это печка... за 3 минуты, кукуруза сварилась😂😂😂 уважуха сказочнику😂.
Капля позитива- конструкция заслуживает внимания👍
Рад, что конструкция понравилась! Иногда простые идеи могут удивить своей эффективностью. Вы бы попробовали сделать что-то подобное?
Это совсем не просто сделать, но главное: А что если электричество вырубят? Есть масса дизайнов, где масло горит без подачи воздуха. Но, в любом случае - Браво!
Une batterie fera l'affaire
Спасибо, что посмотрели наше видео и задали вопросы. Да, сэр, его слабость в том, что без подачи кислорода он не будет сильно гореть, без синего пламени он все равно горит, но в нем много комаров и дыма, что очень опасно, сэр. Спасибо за ваше письмо. Вопрос. Есть ли у вас лучший способ? Пожалуйста, покажите мне. Большое спасибо.
@@lmtn За последние годы, на просторах интернета видел массу различных идей. Возмпжно кпд не у всех одинаковый, но видел печь на отработанном масле для гаража, даже с выхлопом, и это очень важно, так как дышать мы все хотим. Помню пару идей, одна из автомобильных дисков(железных само собой), а вторая из старого баллона от пропана. Они не такие компактные, но рабочие. Ещё видел оборгеватель для маленького дома, там вообще, он ещё меньше вашего и идея заключается в отрожателе. Там парень использует тоненький металл, то ли медь, либо какую-то нержавейку, но зеркальную. Я бы нашёл и скинул, но площадка удаляет ссылки, так что сами поищите.
Ok wirklich gute Idee, aber was ist mit den Abgasen?
I don't think there is any.
@@annwithaplan9766if you burn anything, there always is. It‘s called chemistry.
@@annwithaplan9766 Exhaust gas is given to the user's lungs.
Das ist ein wichtiger Punkt! Abgase wie CO und andere schädliche Stoffe können gefährlich sein. Es ist wichtig, eine gute Belüftung und ggf. eine Abgasreinigung zu haben, um sicher zu arbeiten.
Insert Nathan Fillion Meme here.
MAGNIFICENT INVENTION !! 💯👍
Thank you so much! I'm glad you think so. Your support means a lot! 💯👍
Tried it ..House burned down ,wife took off with neighbour ,dog ran away with her ,crashed my car ,lost my job and on top of all " Beer is finished 😢
Oh no, that sounds like a series of unfortunate events! Hopefully things turn around soon. Remember, it's always good to keep a positive mindset, even when things get tough.
Your life is having a “shitters full moment” persevere man and next time open a window.
Well, it could be worse 😃
And the winner of "The most polluting heater that never should be used indoors or outdoors" is: _________
The one on the electric cars
Your mouth?
Are you crying wipe your tears Karen
Not as bad as coal
@@josephmarciano4761 this is one of them Democrats let's buy an electric car everybody what a joke
No chimney? Carbon monoxide?
Carbon monoxide is the least of your worries with this
تنور آتش بزرگتر دایره وارتفاع کن ومیله باد اش شش ردیف سوراخ کن .
کور خارجی تنور را مستطیل بزرگ کن دارای ذخیره گرما باشد برای کارگاه های صعنتی خوب است بهترین استاد تجربه است.❤❤❤ عالیست❤❤❤
نظر شما عالی است! تغییرات پیشنهادی میتواند کارایی و ایمنی تنور را بهبود بخشد. تجربه همیشه بهترین آموزگار است.❤
Dude needs to watch some welding videos.
Why can’t you just be happy for someone else who made something have you done a tutorial for you tube or are you just a keyboard warrior who hate on people who actually teach others how to do different things
@RobertMorris-l3l Try doing structural and lasting welds like this video shows you. You'll see how is doesn't hold or last very long. You obviously have no idea what makes a good weld.
Millions of people do not know this knowledge! 5 in 1 waste oil heater! Warm for winter 2025
th-cam.com/video/b7-y_VIMTik/w-d-xo.html
Kabayan..magandang araw...bilib ako sa mga gawa mo lalo na u g nsa video n ito ung may mga bilog sa ibabaw...pde kea ako mka request ng ganito sayu for the right price.Thank you kabayan
Kabayan looking forward ako sa reply mo skin...thank you
Look nice...I would be curious to know, if you had the air quality tested coming off the heat of the fire...would it be safe? Or would it contain harmful fumes produced from the chemicals and additives to the origional oil for vehicles?
فكره شبه جيده ولكن يجب توجيه ألغاز للاعلى لا للجانب❤
How do people add a water section to these and make them into rocket heaters or whatever? Is the water in those versions converted into hydrogen and oxygen to make them burn hotter? 🤔 This would be a nice add-on for the waste oil burner wouldn't it❓
Millions of people don't know these technique! 5 ideas 3 in 1 Waste oil heater! Warm for this winter
th-cam.com/users/livekA2DlQJsWSc
Probably 1 in a billion people will ever desire to do this let alone have the ability or resources.. LOL THOUGH crazy this shit gets 10 mil views .. Can you imagine if people had the time desire resources welding abilities or more? There would be these everywhere huh? DOUBTFUL. :D
- TROLLING OUT
10 million know now😂. That's crazy in 3weeks
That is absolutely amazing and awesome
Looks like a good boiler burner! Well done!
Thank you! I'm glad you think so. It was a fun project to work on. I appreciate your feedback and support! Hope it works out great for you too!
It's wonderful when the whole environment where the heater is to be used, is going to stink. The odor of burned oil is something which the neighbourhood surely appreciates. 👍
You're right-burning oil can produce a strong, often unpleasant odor, which isn't ideal for the surrounding area. It's important to make sure that the exhaust is vented properly and that the system is well-maintained to reduce the impact of those fumes. A good filtration system or a better venting solution might help, but it does take some effort to manage. Have you considered any modifications to minimize the smell, or do you just embrace it as part of the process?
Und nun wissen wir, wie jeder Ölofen funktioniert 😊 hierhalt noch mit extra Gebläse und einem coolen Design. Tolles Video 😊
Freut mich, dass dir das Video gefallen hat! Der Ölofen mit extra Gebläse und coolem Design ist wirklich eine effektive und praktische Lösung. Danke für das positive Feedback! 😊
That is one HOT stove. Great work! 🌞
Thank you! It really does get warm. Glad you liked it!
Men you are a genius
Respect!
Thank you so much for the kind words! I really appreciate it. Do you have any suggestions for improving the design?
You are doing great dear friend.
Thank you very much! I am always ready to help you anytime.
Buen trabajo, espero que el conocimiento cada día te haga más práctico y mejores cada uno de tus proyectos. Bendiciones.
Это чудо я скажу что очень хорошая идея вы очень умный человек вопросов нет🎉🎉🎉❤❤❤🎉❤🎉❤🎉❤🎉❤
Спасибо большое за такие приятные слова! Очень рад, что вам понравилось! 😊🎉❤
Какой диаметр верхней трубки
Good idea and nice work! Cheers.
Thank you! Cheers to you too! 😊 If you ever need any advice or want to share ideas, feel free to reach out!
При работе агрегата, автор тщательно скрывает - что стоит на том конце подачи 😀уж не добрый ли газбалон, а то огонь больше чем-то напоминает метан-пропан чем вонючую и дымящую отработку. Ловкость рук и миллион просмотров 😅
Хаха, возможно, автор действительно что-то скрывает! 😉 Иногда в видео используют такие хитрые приёмы для эффектности. Как вы думаете, какие ещё способы можно использовать для улучшения работы агрегатов, чтобы они были безопаснее и эффективнее?
TI SI ČUDO,SVE POHVALE...LP
BACA GEREKMEZ Mİ?
İS YAPMIYOR MU?
ATIK YAĞLAR MOTOR YAĞI MI?
GIDA YAĞI MI?
Eline sağlık
ممنون از ابتکار فناوری واطلاعات لازم بود تقدیم گردید سپاس ❤
تحياتي لك من مصر ❤
Been awhile since I loudly exclaimed "THAT'S GENIUS!" Thank you for the inspiration!
Thank you so much for the kind words! It means a lot to know you found it inspiring. Are there any projects or ideas you're excited to work on next?
İşte bu aradığım video 👌👌👌👌
Me gusta mucho lo felicito
Great design and multi purpose
Thanks bạn nhiều helLo
Very nice successful plan❤
Wow! Your English is absolutely remarkable, for a second grade!!!
Nice to see that, amazing, I have enough this product to make this apparatus 😅😅😅. nice
Glad you liked it! It’s great that you have enough materials to create your own version of the apparatus. Enjoy!
So very cool . Great vid
10 out of 10 just because you use the metric system! I am sure even the oil burns cleaner now!
Thank you! It's great to see appreciation for the metric system. Do you prefer working with specific measurements in your projects?
Video was awesome btw
Thank you so much! I’m glad you enjoyed it. What part of the video did you find most interesting?