Another Incredible Build Video Jeff! Well Done my friend! Every Build is 110% Perfection, the wire run directions, heat shrink, etc... it all absolutely flawless!
You do a very good job@ Thanks for all the helpful tips. Can you explain all the extra parts needed that does not come with the kit? I am starting this build myself. Thank you, and your channel is highly recommended
Thank you! I greatly appreciate that.I’m glad the videos are helpful. What do you mean extra parts? Like what’s need to complete the build other then engine/pipe and electronics?
Me too! Nothing better, are use a crimping tool as well as servo ends www.amazon.com/IWISS-SN-28B-Crimping-AWG28-18-Dupont/dp/B00OMM4YUY/ref=sr_1_5?crid=17ZON2UMO447L&keywords=servo+crimping+tool&qid=1663074119&sprefix=Servo+crimp%2Caps%2C98&sr=8-5 www.amazon.com/WGCD-Universal-Servo-Connector-Female/dp/B06XJV9S1G/ref=sr_1_8?crid=1YIPDLXC4AVV0&keywords=servo+end+connector&qid=1663074173&sprefix=servo+en%2Caps%2C96&sr=8-8
Hi Jeff I have a raw 580 nitro using ikon2 fbl. Question is there a way to fit the srxl2,switch glow driver and xguard rpm sensor? Thank you very much. Your videos are always helpful.
@@Lance57H not a full setup because everything is the same but I have a video just on the governor setup for nitro on iKon. The really the only difference.
I drilled two holes with a 1/8in drill bit then is a Dremel with a cut bit and carefully opened up the hole until I was happy with the switch fitment and then drilled two more holes for the screws.
@@billsrs1982 this is what I use. www.amazon.com/Tulip-41401-Dimensional-Fabric-Paint/dp/B004BQ01CQ/ref=sr_1_3?crid=3MO3A27AVSPUG&keywords=black+fabric+paint&qid=1702513956&sprefix=Lack+fab%2Caps%2C121&sr=8-3
Never, I can’t get the tail to blow no matter what I do. I’ve personally watched one of the hardest 3D smack pilots beat the heck out of a S2 and never blew the tail. There is something wrong.
Good video its fantastic. Please you measure degrees positive and negative maximum (+12 and -12) and after you measure again. At a distance of 3days and reply me the results. Please.
Another Incredible Build Video Jeff!
Well Done my friend! Every Build is 110% Perfection, the wire run directions, heat shrink, etc... it all absolutely flawless!
Thank you! I try my best to make every build flawless! I like them all to be 110% perfect and built to my Standard.
That’s one sweet build, looking forward to you throwing her about the sky 👍🏻
Thank you! I can’t wait!
beautiful machine, great workmanship.
Thank you! I appreciate it!
really clean setup
Thank you! I try and build every heli as clean as I can!
Good vedio and Nice Helicopter
Thank you!
Can't wait to see the flight !
Very soon! Having a issue with the tail servo, so it’s getting replaced!
You do a very good job@
Thanks for all the helpful tips.
Can you explain all the extra parts needed that does not come with the kit?
I am starting this build myself.
Thank you, and your channel is highly recommended
Thank you! I greatly appreciate that.I’m glad the videos are helpful. What do you mean extra parts? Like what’s need to complete the build other then engine/pipe and electronics?
@@westhobbiesrc8051 yes sir
Love the smell of Nitro in the morning. Can you please tell us what you use for making the servo wires shorter.
Me too! Nothing better, are use a crimping tool as well as servo ends
www.amazon.com/IWISS-SN-28B-Crimping-AWG28-18-Dupont/dp/B00OMM4YUY/ref=sr_1_5?crid=17ZON2UMO447L&keywords=servo+crimping+tool&qid=1663074119&sprefix=Servo+crimp%2Caps%2C98&sr=8-5
www.amazon.com/WGCD-Universal-Servo-Connector-Female/dp/B06XJV9S1G/ref=sr_1_8?crid=1YIPDLXC4AVV0&keywords=servo+end+connector&qid=1663074173&sprefix=servo+en%2Caps%2C96&sr=8-8
Happy nitro wagging it's tail
Yes it is! Can’t wait to fly this thing!
Hi Jeff I have a raw 580 nitro using ikon2 fbl. Question is there a way to fit the srxl2,switch glow driver and xguard rpm sensor? Thank you very much. Your videos are always helpful.
@@takito39 hello! Thank you, I greatly appreciate it. What do mean fit it? I run the SRXL2, a glow and Xguard RPM sensor.
I need 1 more port for the battery
I have an ikon2 not the HD version
@@takito39 I run the ikon HD for nitros because they have a power rail. You can Y off the RPM port or Switch glow to add power
@@takito39 you will have to Y power. Use your one open port and tie off RPM or glow port for power.
Is the setup on the Ikon 2 HD for the 580 nitro basically the same as the Raw 700 nitro?
Yes, it’s pretty much the exact same setup.
@@westhobbiesrc8051 do you have a video showcasing a nitro setup on a Ikon2? Particularly a SAB nitro?
@@Lance57H not a full setup because everything is the same but I have a video just on the governor setup for nitro on iKon. The really the only difference.
How much money does it cost to fill the raw 580 tank with nitro fuel ?
I pay $40 a gallon, not sure how many flights it will get per gallon but I’m going to say 12-14 flights per gallon
How did you cut the space for the switch?
I drilled two holes with a 1/8in drill bit then is a Dremel with a cut bit and carefully opened up the hole until I was happy with the switch fitment and then drilled two more holes for the screws.
Sounds good how munch nirto are you using? Thanks
Thank you! Coolpower 30% nitro.
Cant find where do you mount the onboard glow ..
At 11:52, on the inside of the frame at the rear.
Can I use full size servos?
Yes but you will need different servo mounts. They sell the full size mounts.
Nice Raw 🙂The canopy also goes on raw 580 electro ?
Yes the nitro canopy fits on the electric. It is the same mounting.
@@westhobbiesrc8051 Thanks, have a good flight, greetings from Switzerland
What glue are you using for servo plugs on nitro ?
I use black fabric paint for all servo plugs.
@@westhobbiesrc8051 is there specific kind ?
@@billsrs1982 this is what I use. www.amazon.com/Tulip-41401-Dimensional-Fabric-Paint/dp/B004BQ01CQ/ref=sr_1_3?crid=3MO3A27AVSPUG&keywords=black+fabric+paint&qid=1702513956&sprefix=Lack+fab%2Caps%2C121&sr=8-3
What happened to Part 4 of the build….
@@Drumbone71 what do you mean?
@ I cannot find Part 4 in this particular build Series.
@ it’s there. All parts for any/every build are always posted. I really need to spend time and put these videos in playlists.
Thank You. I think I got everything now I needed…. For the build.
@ your welcome! Good luck on your build!
Hello. Did your tail blow out in ur goosky?. Mine always blows out i think I’m sending it a bit too hard
Never, I can’t get the tail to blow no matter what I do. I’ve personally watched one of the hardest 3D smack pilots beat the heck out of a S2 and never blew the tail. There is something wrong.
@@westhobbiesrc8051 do you think it’s because of the throttle curve? I’m running like 65 or 70%
@@Twx97 definitely not, I’m running 100% on mine. Never got the tail to even come close to letting go. Make sure the tail blade is on the right way.
@@westhobbiesrc8051 do you have an email so i can send you a video of it blowing out with a simple move?
@@westhobbiesrc8051 and also it looked like i was running it on 30% throttle curve on the tx16s do you think that is why?
you in TN area?
Yes I am!
Mt Juliet here. Nice very nice!@@westhobbiesrc8051
Nice😉👍
thank you!
@@westhobbiesrc8051 My raw 580 nitro will arrive in a few days. Nice to have seen how the build went 👌
@@rtoebak76 awesome! Enjoy the build! It’s a great one!
Butiful!!
Thank you! It’s a incredible model!
Good video its fantastic.
Please you measure degrees positive and negative maximum (+12 and -12) and after you measure again.
At a distance of 3days and reply me the results.
Please.
I run 13 degrees +/- it won’t change at all no matter how many days, months or years. If it is changing there’s something wrong in the FBL unit.