instead of pounding to the side.. why not modify a forged ring eye to a tapered pipe thread pipe plug so its a solid thread then you can lever it out or use a small slide hammer with a hook or chain thru the forged ring eye.. i worked in an engine rebuilding shop back in the 1990s.. the tear down guy got the engines that were covered a half inch thick in grease.. he hated those. since it was hanging on the hoist about to drop on his tear down bench.. i said lets try this.. and rolled it over and set it down on the spray wash tank and gave it a spin in the washer.. came out mostly clean and much easier to tear down. as long as you plug the hydraulic holes with real metal plugs not plastic. wash away before tear down. when i change the oil in final drives.. i drain and refill.. as normal. but then i get the track up in the air and i run it for a few minutes with no load.. just the track zooming around.. i then drain it again.. refill.. now i know i have gotten a much higher percentage of grime out of the gears.. when its really bad.. i have done it 3 times. each time running the drive to stir up sediment that the clean oil can suspend easier.
Hi, Jay. It is really not needed. Once the snap ring (cir clip) holding the two together is removed they usually come apart rather easily. A press could be used in the instances where they are difficult to separate.
It would be good to show what parts move and what bits don't. I'm trying to figure out how the gearing works and how the motor drive gets to the final cog.
The machine I got is a terex tc35, I think it’s the same drive motor. We bought it with the snap ring missing, my guys now routinely repack the final drives themselves on site. Should I send it your way ?
I've lost drive to the left track on my takeuchie tb035 mini excavator and I'm think the final drive has detached? The right hand track is working fine so I don't think it's a pressure problem? Do you guys have any ideas on what it could be? Great video by the way!!
Yes. A very interesting and educational look at what it takes to finish a job.
instead of pounding to the side.. why not modify a forged ring eye to a tapered pipe thread pipe plug so its a solid thread then you can lever it out or use a small slide hammer with a hook or chain thru the forged ring eye.. i worked in an engine rebuilding shop back in the 1990s.. the tear down guy got the engines that were covered a half inch thick in grease.. he hated those. since it was hanging on the hoist about to drop on his tear down bench.. i said lets try this.. and rolled it over and set it down on the spray wash tank and gave it a spin in the washer.. came out mostly clean and much easier to tear down. as long as you plug the hydraulic holes with real metal plugs not plastic. wash away before tear down. when i change the oil in final drives.. i drain and refill.. as normal. but then i get the track up in the air and i run it for a few minutes with no load.. just the track zooming around.. i then drain it again.. refill.. now i know i have gotten a much higher percentage of grime out of the gears.. when its really bad.. i have done it 3 times. each time running the drive to stir up sediment that the clean oil can suspend easier.
Seems like swashplate needs good additives in hydraulic oil. Is there any oil standard these drive motors require?
Nice work colleagues !
Thank u . Show us rebuilt
can a 20 ton press be used to press apart the hubs on a 331 final drive
Hi, Jay. It is really not needed. Once the snap ring (cir clip) holding the two together is removed they usually come apart rather easily. A press could be used in the instances where they are difficult to separate.
@@Finaldriveparts thanks guys .And if I need any service or need any final drive units for our equipment your the first on my list to go with.
It would be good to show what parts move and what bits don't. I'm trying to figure out how the gearing works and how the motor drive gets to the final cog.
How much will it cost to remain the tracking motor
Do you have a part name retainer for bobcat E45 ?
Do you have a video on removing the final drive motor? I have a 303cr and want to change out my bad for a new one on my own.
The machine I got is a terex tc35, I think it’s the same drive motor. We bought it with the snap ring missing, my guys now routinely repack the final drives themselves on site. Should I send it your way ?
Could you give us a call at 877-634-3826? One of your experts will be able to answer your question.
I've lost drive to the left track on my takeuchie tb035 mini excavator and I'm think the final drive has detached? The right hand track is working fine so I don't think it's a pressure problem? Do you guys have any ideas on what it could be? Great video by the way!!
Hi, Marcus. I forwarded this question to one of our experts. I'm waiting back to hear from him.
Our expert says that it sounds like the motor needs to be replaced. Please feel free to call into the office for details
281-259-5267.
FinalDriveParts.com
Thanks for your knowledge sharing.
Damn right, great informative video, This is the stuff I like to see. I enjoyed this.
Dam right Ricky
make more video.. make video on how to tune two speed skid steer
Update pleases.Would love to see where this goes!!
sub
What tools did you use that’s my main issue.
Grazie per il video!
Mmmm sludgy....it takes a looooooong time for gear case lube to get like that.
It does indeed!
My final drive motor is leaking oil not fro the hydraulic section but around the motor itself
Do you have any vid's on how the drive works ??
No, we don't -- but this one might help: th-cam.com/video/hpAgZ9-4rYA/w-d-xo.html
Well change that next month I promise
I need parts for my Mitsubishi trackhoe m o s 70 the final drive gear can you help me find it
Frn do you have mitsubishi me30 final drive assembly list please
thanks man that really helped me out :)
Nice job
great video! I learned a lot.
Thank you, @Mark Ervin!
Co ban khong
Ban co biet sua Drive Motor khg ? ban o Viet Nam a ?
Thanks
Обратно собрать сможешь? )))
Boy there's nothing wrong with that
Fr
Bobcat
Nervous man
Gurit bulat simpan bol byring 2,3 yang tiga batang tu shalp all to wo bol byring 22 biji