The biggest benefit of a Texan is that if you invest in a 4500 psi compressor and buy molds ,use wheel weights ,you can shoot for free. I'm buying the 50 Cal Texan with the super valve heavy hammer spring and a few 510 diameter molds. 396 and a 412 grain. I'm getting a us made 4500 psi compressor and a few 4500 psi scuba tanks. I can run my HKs and AKs ,but that cost money. If you spend the money on investing into a full setup with a Texan it's free essentially
My thoughts, You will spend thousands of dollars just to have to carry that all around. If somthing goes down and you have no electricity, or there’s an apocalypse etc. The only way to pump it is a manual pump. That takes too long. Someone is just gonna shoot you within that 15 minutes. You also only get like 6 shots. Vs buying a nice semi auto rifle for 600 or a nice sniper rifle in the sale section at cabelas for 300. Then you buy thousands of bullets over time and be able to have all that in an apocalypse. Way easier than air
Hey you know it looks like you did a really nice upgrade on that air rifle and it may be the most powerful 4 45 caliber air rifle but for $1,900 you probably would have been better off just to have got the Zeus air rifle I know it's a 72 Cal but I believe that one is truly the most powerful air rifle you can get they call it the 12 gauge shotgun
It's good that you mention the air consumption con. I own a bushbuck and it gets max power at 3800 psi. I thought I wanted more power, was looking into one of the more powerful options but they all need that higher pressure and I do like to shoot for a while. dont want to take more than just my one large tank with me, that's ultimately why I decided to stick with the bushbuck.
You know when you're right you know a lot of these are gone guys want to push all this PSI filled to the Limit who's to say this texting here wouldn't give you better performance with a 4,000 PSI fill instead of 44 just because you can fill it the 45 doesn't mean that it will shoot the best there that's all I'm saying
@@donwilson350 yes. The bushbuck is actually this way. The manual said it could be filled to as much as 4400 PSI IIRC, but it gets best velocity around 3800 as I mentioned. However, there are big bores that do get their best power at the higher number where you'll get way less shots at that pressure before your tank runs low...
Smaller calibers are more fun. Over a 100 regulated shots with my .25 and the thing is a laser. Big bores are cool but the ammo is expensive and the shot count just really sucks the fun out of em
@@asherr5966 my aea 50 caliber Challenger is the same I can fill up to 4500 but I will have no max power until 3800 mark just too much pressure for hammer spring I only like to overfill to 4500 when I'm Target practicing gives me like a 16 shot total
@@donwilson350 you won't get better foot pounds of 4500 PSI.. it's always your sweet spot .. 3800 PSI and below I own an aea Challenger 50 caliber and I filled to 4500 for more shots not powerful shots.. 3600 when I want to get it done
Thank you for the review. I don't own an air rifle, but you've placed a little seed in the brain. That said, I don't think I'm into the refueling on them along with projectile costs. I think I'm, (me) further ahead to just keep pulling the trigger on my 17wsm, at $18.00 for 50 rds. I'm a pig hunter, I watched your CO hunt. I'm sure you know about shooting those big bore hogs a shoulder, NOT good shot placement unless you've got some beef, though you did fine. Head and high neck are my only choices with small caliber, and would probably be the same for me if using air. If I. can find someone in my local area I would give it a try. Oh, the $1,800 price tag is pretty much a game killer as well. That said, enjoyed your video and the education you're putting out there and I did subscribe with a thumbs up!
I hate when people start saying ,, that to much power ,, that’s over kill ,,, why pay all that extra money,, Well it’s fun an we are in America,, 😁 ,, awesome gun man I do all the same to my big bores,, hell I bought a little Diana bandit pistol 22 An turned it in to a 40 fpe 5 shot pistol,,lol ,, great video subbed 👍👍
I have one of his valves on my .50 rexp and it’s a monster now . My wife killed two young pigs with it within 5 minutes both were pass throughs . Probably a 45 and 70 lb
The stock valve can handle the 3600 psi like the new valve I just put a new hammer spring around 3/4 more longer than the stock spring I bought it at hardware store Now I get 100 fps more than before The only problem is the lock on the trigger get stuck when the air gets down around 2500 psi I need to figure out what i can do with it And the other problem is the trigger It gets much more sensitive so with little push it shoots so be careful with it I'm still trying to figure out why when I turn all the way inside the power wheel The trigger lock get stuck So I have to turn back the power wheel Till I can unlock the trigger And like I said just be careful with the trigger!
What does the heavy spring do to trigger pull? Other than having to run heavier lead for grouping did the general accuracy/grouping stay about the same as before the upgrade?
Hello from Littleton. I have a bunch of air rifles and 5 acres down by Ft. Garland. I have a TC45, bunch of 22xx builds, Vectis, Benjamin .25 Nitro Mag, Gamo Swarm Mag .22, Crosman Diamondback, Hatsan .25 springers, and more. All virtually or brand new. Be my pleasure to go shoot/film whatever.
Am a performance engine technician so I immediately started hot rodding all my airguns. Been contemplating a channel but a collaboration might be possible
Awesome! We should get together! I'd like to put a shoot together soon with all the guys from Colorado. Thanks for saying hi. Wow you have a lot of airguns.
@@ColoradoAirgunner excellent! I will send an email to mtnfish2469@gmail.com tomorrow with my phone # if that email still works (listed on your youtube page)
Hello i have a doubt, what is the brand of the carbon fiber bottle? i know that seller is africanairordnance but i want know the brand of their bottles thanks
The only thing it’s missing is a suppressor instead of a muzzle brake and it’s perfect. Nothing’s quieter than a suppressed air rifle, since at full power you’re subsonic why not suppress it? Who cares about recoil control over sound suppression when it’s just a single shot? The recoil shouldn’t matter a bit as long as your stable and confident with your rifle/scope setup. It would be different if you had a muzzle brake/compensator on say a threaded barrel 10mm XDM (which I have one with a compensator and love it dearly) where most ammo is loaded on the supersonic side and it’s semi automatic with a high capacity so a compensator over a suppressor makes more sense. Not to mention 10mm does have recoil that needs to be tamed for a quick follow up shot, no matter what in this case however the reloading process takes to long for it to matter. My Texan LSS in .308 with the stock 3000psi tank is of course very tame in recoil, the shrouded barrel and suppressor also minimally helps the recoil, but really it’s because it’s not there in the first place. Even if it was though I would much rather suppress than compensate when givin the choice on the Texan. Nothing is more valuable than being stealthy in the woods if you want to bag more critters or not scare surrounding wildlife or even neighboring people suppress that bad boy, it’s just calling out for one.
so if i already have the carbon fiber tx2 texan 45 all i would need is the bottle? i think the tx2 version of the texan comes with the magnum spring...?
Theres a limit even with gunpowder like u could put a 20 grain bullet neck down a 50 bmg and only get like 5800 fps not 100000 fps because theres a limit of how fast the gas can expand same with air u can increase the pressures in the future but there will be a limit tk how fast air can expand
Was shooting mines yesterday breaking it in,jus wanted to get an ideal, it'll b maxed out ,I still gotta order the new New AAO 2021 Texan Stainless Steel Carrier Tube ,,
The biggest benefit of a Texan is that if you invest in a 4500 psi compressor and buy molds ,use wheel weights ,you can shoot for free. I'm buying the 50 Cal Texan with the super valve heavy hammer spring and a few 510 diameter molds. 396 and a 412 grain. I'm getting a us made 4500 psi compressor and a few 4500 psi scuba tanks. I can run my HKs and AKs ,but that cost money. If you spend the money on investing into a full setup with a Texan it's free essentially
My thoughts, You will spend thousands of dollars just to have to carry that all around. If somthing goes down and you have no electricity, or there’s an apocalypse etc. The only way to pump it is a manual pump. That takes too long. Someone is just gonna shoot you within that 15 minutes. You also only get like 6 shots. Vs buying a nice semi auto rifle for 600 or a nice sniper rifle in the sale section at cabelas for 300. Then you buy thousands of bullets over time and be able to have all that in an apocalypse. Way easier than air
Hey you know it looks like you did a really nice upgrade on that air rifle and it may be the most powerful 4 45 caliber air rifle but for $1,900 you probably would have been better off just to have got the Zeus air rifle I know it's a 72 Cal but I believe that one is truly the most powerful air rifle you can get they call it the 12 gauge shotgun
It's good that you mention the air consumption con. I own a bushbuck and it gets max power at 3800 psi. I thought I wanted more power, was looking into one of the more powerful options but they all need that higher pressure and I do like to shoot for a while. dont want to take more than just my one large tank with me, that's ultimately why I decided to stick with the bushbuck.
You know when you're right you know a lot of these are gone guys want to push all this PSI filled to the Limit who's to say this texting here wouldn't give you better performance with a 4,000 PSI fill instead of 44 just because you can fill it the 45 doesn't mean that it will shoot the best there that's all I'm saying
@@donwilson350 yes. The bushbuck is actually this way. The manual said it could be filled to as much as 4400 PSI IIRC, but it gets best velocity around 3800 as I mentioned. However, there are big bores that do get their best power at the higher number where you'll get way less shots at that pressure before your tank runs low...
Smaller calibers are more fun. Over a 100 regulated shots with my .25 and the thing is a laser. Big bores are cool but the ammo is expensive and the shot count just really sucks the fun out of em
@@asherr5966 my aea 50 caliber Challenger is the same I can fill up to 4500 but I will have no max power until 3800 mark just too much pressure for hammer spring I only like to overfill to 4500 when I'm Target practicing gives me like a 16 shot total
@@donwilson350 you won't get better foot pounds of 4500 PSI.. it's always your sweet spot .. 3800 PSI and below I own an aea Challenger 50 caliber and I filled to 4500 for more shots not powerful shots.. 3600 when I want to get it done
Thank you for the review. I don't own an air rifle, but you've placed a little seed in the brain. That said, I don't think I'm into the refueling on them along with projectile costs. I think I'm, (me) further ahead to just keep pulling the trigger on my 17wsm, at $18.00 for 50 rds. I'm a pig hunter, I watched your CO hunt. I'm sure you know about shooting those big bore hogs a shoulder, NOT good shot placement unless you've got some beef, though you did fine. Head and high neck are my only choices with small caliber, and would probably be the same for me if using air. If I. can find someone in my local area I would give it a try. Oh, the $1,800 price tag is pretty much a game killer as well.
That said, enjoyed your video and the education you're putting out there and I did subscribe with a thumbs up!
I hate when people start saying ,, that to much power ,, that’s over kill ,,, why pay all that extra money,, Well it’s fun an we are in America,, 😁 ,, awesome gun man I do all the same to my big bores,, hell I bought a little Diana bandit pistol 22 An turned it in to a 40 fpe 5 shot pistol,,lol ,, great video subbed 👍👍
Thank you sir! To much power? Whaaaat?
Just had to rewatch! Such power
Dam brotha that thing is a beast that's some power thanks for sharing
I'm looking at getting the 4500 tank and a compressor. Hand pumping for now...
At least a tank.
I have one of his valves on my .50 rexp and it’s a monster now . My wife killed two young pigs with it within 5 minutes both were pass throughs . Probably a 45 and 70 lb
Nice! They are awesome. Converting it to a .50 caliber super Tex now.
Hey buddy, love my Texan now!!!! I’m getting 1,018 FPS with a 350 grain bullet. That’s at 4500 psi and my hammer spring halfway.
Very cool. Ya gotta love it!
Would you tell me What part item must I change to get 1000 fps. Please give me a Link website for get the part Thanks. 🙏🙏
@@jokopurnomo97, just google African Air Ordanance or Lethal Air and just click on the website.
@@longislandairgunner1600 Thanks for your answer. But what part must be change to get more 100 fps with 350 grain?
You will need the 4500 psi tank either metal or carbon. The valve. And the magnum hammer Spring.
The stock valve can handle the 3600 psi like the new valve
I just put a new hammer spring around 3/4 more longer than the stock spring
I bought it at hardware store
Now I get 100 fps more than before
The only problem is the lock on the trigger get stuck when the air gets down around 2500 psi
I need to figure out what i can do with it
And the other problem is the trigger
It gets much more sensitive so with little push it shoots so be careful with it
I'm still trying to figure out why when I turn all the way inside the power wheel
The trigger lock get stuck
So I have to turn back the power wheel
Till I can unlock the trigger
And like I said just be careful with the trigger!
Good to know.
Your sear pin might be wearing its the most front pin towards the muzzle
great info.. Thankyou. I would like to ask if its possible to switch from steel to fibre tank. I have the 50 cal carbine.
What does the heavy spring do to trigger pull? Other than having to run heavier lead for grouping did the general accuracy/grouping stay about the same as before the upgrade?
Didn't adjust the power wheel spring tension for different weight slugs. That might have made a difference
Hello from Littleton. I have a bunch of air rifles and 5 acres down by Ft. Garland. I have a TC45, bunch of 22xx builds, Vectis, Benjamin .25 Nitro Mag, Gamo Swarm Mag .22, Crosman Diamondback, Hatsan .25 springers, and more. All virtually or brand new. Be my pleasure to go shoot/film whatever.
Am a performance engine technician so I immediately started hot rodding all my airguns. Been contemplating a channel but a collaboration might be possible
Awesome! We should get together! I'd like to put a shoot together soon with all the guys from Colorado. Thanks for saying hi. Wow you have a lot of airguns.
@@dreamstreetskate5291 yea lets do a video! I'm in Littleton as well.
@@ColoradoAirgunner excellent! I will send an email to mtnfish2469@gmail.com tomorrow with my phone # if that email still works (listed on your youtube page)
@@dreamstreetskate5291 yes sir.
Hey buddy, what did you set your hammer spring at? Did you have it midway, 3/4?
Maxed out for the big stuff, over 350 grains. 3/4 for the sub 350 stuff.
So with all the power what's the shot count with out the scuba tank ? One shot gun ?
5-6 shots per fill.
Great video!!!
Can you use nitrogen with that tank??
Yes you can!
Thumbs up subbed, I wonder what fps you could get out of a 190 grn hp
Great video
Hello i have a doubt, what is the brand of the carbon fiber bottle? i know that seller is africanairordnance but i want know the brand of their bottles
thanks
Not sure. Standard carbon 4350psi bottle. Lethal Air has them on his site.
The only thing it’s missing is a suppressor instead of a muzzle brake and it’s perfect. Nothing’s quieter than a suppressed air rifle, since at full power you’re subsonic why not suppress it? Who cares about recoil control over sound suppression when it’s just a single shot? The recoil shouldn’t matter a bit as long as your stable and confident with your rifle/scope setup. It would be different if you had a muzzle brake/compensator on say a threaded barrel 10mm XDM (which I have one with a compensator and love it dearly) where most ammo is loaded on the supersonic side and it’s semi automatic with a high capacity so a compensator over a suppressor makes more sense. Not to mention 10mm does have recoil that needs to be tamed for a quick follow up shot, no matter what in this case however the reloading process takes to long for it to matter. My Texan LSS in .308 with the stock 3000psi tank is of course very tame in recoil, the shrouded barrel and suppressor also minimally helps the recoil, but really it’s because it’s not there in the first place. Even if it was though I would much rather suppress than compensate when givin the choice on the Texan. Nothing is more valuable than being stealthy in the woods if you want to bag more critters or not scare surrounding wildlife or even neighboring people suppress that bad boy, it’s just calling out for one.
I like suppressors too! I have an Emperor from DonnyFL for it. It'd just so long to carry hunting.
@@ColoradoAirgunner i just carry mine in my back pack and put it on in the stand or if i sit on the ground
so if i already have the carbon fiber tx2 texan 45 all i would need is the bottle? i think the tx2 version of the texan comes with the magnum spring...?
You would need the valve, magnum spring, and a 4350psi bottle. Either carbon or metal. The spring from AAO is stronger.
Which is a bigger better gun .457 cal or .50 cal lss
the fifty is for sure.
Amazing
Where you get the barrel brake from?
what is the regulator you using on the tank?
Good day sir i want to know how much this airgun airforce texan pls reply
Does it come with the surpresser on end
No. It's a DonnyFL.
Here’s my question, Airforce will disavow your warranty on your rifle, if you disassemble it.So taking the rifle apart is a problem, so then what;
It's on you. But Chad at Lethal Air airgun shop services them.
Надо вдвоём ее таскать 😂😂😂,, leshiy 2 ❤ made in Russia ❤
How much price
With custom pellets and lighter pellets can speed up to 5000FPS
Theres a limit even with gunpowder like u could put a 20 grain bullet neck down a 50 bmg and only get like 5800 fps not 100000 fps because theres a limit of how fast the gas can expand same with air u can increase the pressures in the future but there will be a limit tk how fast air can expand
Question so off of a 100cf tank at 4500 psi how many top off do you get like three or four before you have to swap tanks?
Nice gun...
Thanks!
please go more into how you got the valvebody out of the bottle....most brands use some sort of loctite/sealant and can be a b*tch to get off
It comes on the bottle. It does not need loctite. Just hand tighten and removed by hand as well.
Great video if you dont mind I'll be sharing on FB let's see if we can get you more subscribers
Thanks Jeremy!
"in the world" and "on the planet today" is replacing the absolute with a lesser expression.
Where is the strap on crono how are you getting your number. Lmao
13:00 All that wind noise sucks a bunch.
That's about as much fpe as an AR15.
that's a lot of work for an extra hundred feet per second
A lot of guys would really like to have an extra 200 foot pounds of energy over a carbon tx2 Texan. It's very easy to install.
200 foot pounds of energy not feet per second
@@MenardRebelRiders bet those numbers dropped your jaw! lol FPE not FPS ! 😎
@@MenardRebelRiders
How you want to get more FPE without increasing the speed?
The more faster it go the more FPE you get
@@maryokelly9674
Mass
About wer is ur power wheel set
All the way back.
Was shooting mines yesterday breaking it in,jus wanted to get an ideal, it'll b maxed out ,I still gotta order the new New AAO 2021 Texan Stainless Steel Carrier Tube ,,
I had ordered the upgrade 2021 upgrade kit n m. spring n hammer
Sure your 500ft from a dwelling out there? 😆
Ha.
What compressor do you use?
Omega supercharger.