IT IS IMPERATIVE TO DO AN OIL CHANGE AND FILTER AFTERWARD,HERE IS THE OIL FILTER AND OIL LINK amzn.to/47hw7kL amzn.to/47hI369 Link for the high pressure fuel pump amzn.to/40mAqJe Fuel line amzn.to/47hG9T3 Trim tools amzn.to/3st7LFQ Basic hand tool set amzn.to/3Qxri0b High pressure fuel pump installation tool www.freedomracing.com/en-48896-high-pressure-fuel-pump-installer-alt-st-259.html Fuel line quick disconnect tool amzn.to/3Ms1yRv
what if the bearing is bad? I replaced the high pressure sensor and fuel pump. The car will run great for about 20 to 30 miles then go into low power mode and I get the p0191 code again. Let it sit for a while clear the code then it runs good and back to the same problem. Will a bad bearing make this happen? not sure if the mechanic checked out that bearing on the camshaft.
@@steevegmtech7326 checked the wiring and it was good. Still doing the same thing. Getting a P0172 code also. Will replace the fuel pump again and check the bearing next.
@@steevegmtech7326 I just swapped my pump out started it up and it's still not wanting to shut off right away do I have to run it for a little bit or clear the codes or you think I have a diff issue I changed oil n filter also but turn the key off still wants to keep running
Here is the link for the tool , you turn the cam until it reach the round part not the oblong part, you can use your finger carefully to have a feel for it www.amazon.com/gp/aw/d/B0CTTLD5QX/ref=ox_sc_act_image_1?smid=A1W16FGXVBTKLK&psc=1&tag=steevegmtec03-20
IT IS IMPERATIVE TO DO AN OIL CHANGE AND FILTER AFTERWARD,HERE IS THE OIL FILTER AND OIL LINK
amzn.to/47hw7kL
amzn.to/47hI369
Link for the high pressure fuel pump
amzn.to/40mAqJe
Fuel line
amzn.to/47hG9T3
Trim tools
amzn.to/3st7LFQ
Basic hand tool set
amzn.to/3Qxri0b
High pressure fuel pump installation tool
www.freedomracing.com/en-48896-high-pressure-fuel-pump-installer-alt-st-259.html
Fuel line quick disconnect tool
amzn.to/3Ms1yRv
Excellent!
Thank you
Is there anything I can use if I don’t have the special tool to make sure the camshaft is in the right position?
www.freedomracing.com/high-pressure-fuel-pump-installer-en-48896.html
Can i turn camshaft without removing wheel?
Yes you can just awkward
Do u have to move camshaft?
Yes you can, turn the wheel to the right before you take things apart
Would my car dieing when I'm parking be another symptom of this being bad or severe chugging at a red light
It is positive if it is at its last stage
what if the bearing is bad? I replaced the high pressure sensor and fuel pump. The car will run great for about 20 to 30 miles then go into low power mode and I get the p0191 code again. Let it sit for a while clear the code then it runs good and back to the same problem. Will a bad bearing make this happen? not sure if the mechanic checked out that bearing on the camshaft.
@Donzgalore that's a possibility, have him the wiring to the fuel pump also
@@steevegmtech7326 checked the wiring and it was good. Still doing the same thing. Getting a P0172 code also. Will replace the fuel pump again and check the bearing next.
That code mean your vehicle is running richit is using more fuel than usual,I would focus on they code now
I have a P0089 an P228D p0013 for a 2012 Buick regal 2.4l any tips?
I think it is the same procedure ,quite common on those 2.4
Change the oil to remove fuel contamination. Another symptom of a leaking HPFP is dieseling or engine run-on.
I did change the oil and filter afterward, thanks for mentioning that
Does it make a difference if the oil was changed beforehand?@steevegmtech7326
Depends on how many miles you already put on it, just to be safe change the oil , it is cheaper than an engine
@@steevegmtech7326 I just swapped my pump out started it up and it's still not wanting to shut off right away do I have to run it for a little bit or clear the codes or you think I have a diff issue I changed oil n filter also but turn the key off still wants to keep running
That's not normal, what are the codes stored in the ecm
Where did you get the tool to reset the cam?
www.amazon.com/gp/aw/d/B0CTTLD5QX/ref=ox_sc_act_image_1?smid=A1W16FGXVBTKLK&psc=1&tag=steevegmtec03-20
What’s the name of the blue tool ?
Fuel line quick disconnect
www.amazon.com/gp/aw/d/B0BQ54QF96/ref=ox_sc_act_image_1?smid=A2NSTN4HNN6O8K&psc=1&tag=steevegmtec03-20
May I have the link for the fuel line removal tool as well as the black plug you used for the camshaft alignment??
www.freedomracing.com/en-48896-high-pressure-fuel-pump-installer-alt-st-259.html
Where do I find this black tool? If not how many times do I have to turn the camshaft
Here is the link for the tool , you turn the cam until it reach the round part not the oblong part, you can use your finger carefully to have a feel for it
www.amazon.com/gp/aw/d/B0CTTLD5QX/ref=ox_sc_act_image_1?smid=A1W16FGXVBTKLK&psc=1&tag=steevegmtec03-20
Great, thank you
You welcome 👍
Where can I get the little alignment tool for the fuel pump ?? I’m in California and can’t find it.
www.freedomracing.com/high-pressure-fuel-pump-installer-en-48896.html
AFTER THE FUSES DO YOU HAVE TO DISCONNECT THE BATTERY ????????? OR IS IT ALWAYS GOOD TO DISCONNECT THE BATTERY???
@chrisssmith3206 not necessary
Thank you sir for your wonderful instructions!! I am now a follower!!!
You welcome 👍
Anyone knows the part# on Amazon for the fuel feeding pipe?
www.amazon.com/gp/aw/d/B010GMLD6G/ref=ox_sc_act_image_1?smid=A828HHPH5ON29&psc=1&tag=steevegmtec03-20
It is not necessary to grieve replace the fuel feed pipe
Nonsense.. you cut how difficult it was to remove e the pump .
That's the easiest part of it, you missing something