I bought one of these. I use it on a 41hp tractor, and it runs it no problem. It does the best on pine trees and other soft woods. On hard woods it chatters a bit and you obviously have to watch that and slow down, other then that, for the price to own a stump grinder it's a great thing to have. I couldn't believe the price of stump grinders in general when i looked for one, this a great option if you already have a tractor.
Will this thing work on one of those old red and gray Ford Red Belly tractors? Or one of the old blue and white Ford tractors from probably the 60s or 70s? I know thats not a lot of info. Thinking of buying one of my buddys tractors he has for sale and getting this stump grinder. Its the most bang for the buck that I have found so far if they will work together. Also, does it hurt them to run them through the dirt? I know you dont wanna run a chainsaw in the dirt or it will ruin the blade. How do the teeth wear when running them through the dirt on either side of the stump? Thanks for any info!
Hi Brady, Hydrostatic transmissions are ideal, but many customers have used the stump grinder with manual transmissions. Just check to see if your tractor utilizes a two-stage clutch. This means that when the clutch is depressed halfway, it will disengage the transmission and allow the operator to control or vary the travel speed, but still allow the PTO to operate independently of the transmission and at full operating speed of 540 RPM during the grinder usage.
The WG24 stump grinder is to be operated at 540RPM and is rated for tractors with up to 45HP, therefore unfortunately, your Kubota M5 would be outside of this range and not recommended.
Please visit our website where you can check your tractors compatibility or email sales@woodlandmills.com or call us toll free to discuss at 1-855-476-6455
Hi Robert, Thanks for your comment. You can call us toll free from the USA/Canada at 1-855-476-6455 or go to our website for more info: woodlandmills.ca/us/product/wg24-stump-grinder/ Thanks, Neil
2 questions related to my subcompact 19 PTO HP (25 HP engine) Massey GC1720: 1) will the Subcompact power this well enough? 2) What is typical service life of the cutting blade?
Hi Larry, 1) The WG24 will work fine for a tractor with 19HP @ the PTO. Depending on what you are grinding will determine how much of a cut you can take in one pass. You can visit our website for more information or call us with any other questions. 2) With the teeth it will depend on what type of ground you are grinding into. With sandy ground your teeth will last quite awhile and if you are cutting through rocky ground the teeth will wear out faster. There are too many variables to provide a life span on the teeth such as Ground conditions, weather condition (summer vs winter) and hardwood vs softwood
I bought one of these. I use it on a 41hp tractor, and it runs it no problem. It does the best on pine trees and other soft woods. On hard woods it chatters a bit and you obviously have to watch that and slow down, other then that, for the price to own a stump grinder it's a great thing to have. I couldn't believe the price of stump grinders in general when i looked for one, this a great option if you already have a tractor.
Wow! A company that actually shows uncut videos of their product being used! Think I may buy one!
Love to hear it! :)
Dang. I need to show my boss this. I cut down so many trees that grow under fences. This would sure help a ton getting the trees to not grow back.
Very satisfactory
In the manual it states you should grind right to left looking from the rear of the grinder. This is left to right. Which is correct?
Hi Fred, Grinding from the right to the left as shown in the manual will yield a smoother operation.
Is it direct drive off the pto shaft or is there a gearbox.? How can I get more info
Hi Tim, It is direct drive. Also, you can contact our staff at 1-855-476-6455 with any questions you may have. Thank-you
Would a john deere 3025e run this?
Hi Jeff, we recommend 20-45 HP at the PTO. Slightly less could still work. It's best to confirm your HP at the PTO and give us a call. 1-855-476-6455
I need one of these in my life. my 3038e has 30pto hp so should run easy then?
Yes, that will be plenty of horsepower for the stump grinder to work well.
Will this thing work on one of those old red and gray Ford Red Belly tractors? Or one of the old blue and white Ford tractors from probably the 60s or 70s? I know thats not a lot of info. Thinking of buying one of my buddys tractors he has for sale and getting this stump grinder. Its the most bang for the buck that I have found so far if they will work together. Also, does it hurt them to run them through the dirt? I know you dont wanna run a chainsaw in the dirt or it will ruin the blade. How do the teeth wear when running them through the dirt on either side of the stump? Thanks for any info!
Please give us a call 1-855-476-6455 to discuss the tractor's PTO HP and visit our website at www.woodlandmills.com for more info.
Thing is a beast
Wonderful job. :)
Hi I was wondering if that stump grinder has a 540 PTO shaft size?
The stump grinder is designed to work off of a tractor PTO that rotates at 540RPM.
The shaft on the stump grinder is a standard 6 spline.
Will this unit work with a John Deere "I match" three point hitch adapter?
Yes, any questions please email sales@woodlandmills.com or visit our website at www.woodlandmills.com
how many pto horsepower do they need to run that..
You can run our stump grinder with as little as 18HP at the PTO.
Can you run this on a shuttle shift without destroying your clutch?
Hi Brady, Hydrostatic transmissions are ideal, but many customers have used the stump grinder with manual transmissions. Just check to see if your tractor utilizes a two-stage clutch. This means that when the clutch is depressed halfway, it will disengage the transmission and allow the operator to control or vary the travel speed, but still allow the PTO to operate independently of the transmission and at full operating speed of 540 RPM during the grinder usage.
So what model would be best for 90 PTO hp like kubota M5-111-1? Also is it 540 or 1000 rpm?
The WG24 stump grinder is to be operated at 540RPM and is rated for tractors with up to 45HP, therefore unfortunately, your Kubota M5 would be outside of this range and not recommended.
@@woodlandmillsJust clarifying, 45 hp at the pto or overall?
Price?
Please visit our website www.woodlandmills.com or call us toll free 1-855-476-6455, email sales@woodlandmills.com
I'm guessing a bx23s is too small to run this? Nice implement!
Please visit our website where you can check your tractors compatibility or email sales@woodlandmills.com or call us toll free to discuss at 1-855-476-6455
I live in Duluth MN, where do I get info to purchase one of these?
Hi Robert,
Thanks for your comment. You can call us toll free from the USA/Canada at 1-855-476-6455 or go to our website for more info:
woodlandmills.ca/us/product/wg24-stump-grinder/
Thanks,
Neil
2 questions related to my subcompact 19 PTO HP (25 HP engine) Massey GC1720:
1) will the Subcompact power this well enough?
2) What is typical service life of the cutting blade?
Hi Larry, 1) The WG24 will work fine for a tractor with 19HP @ the PTO. Depending on what you are grinding will determine how much of a cut you can take in one pass. You can visit our website for more information or call us with any other questions.
2) With the teeth it will depend on what type of ground you are grinding into. With sandy ground your teeth will last quite awhile and if you are cutting through rocky ground the teeth will wear out faster. There are too many variables to provide a life span on the teeth such as Ground conditions, weather condition (summer vs winter) and hardwood vs softwood
Handy machine do you still stock or make them ?
Yes, please check our website www.woodlandmills.com or give us a call 1-855-476-6455
Good tank you
0840 Nikita Plains