@@EVCustomscan you tell me whay my 1 motor after i change the hall sensors is taking to much ampers the 2 motor takes 1.5 ampers but 1 motor is taking 10 ampers
Great instructional video. I noticed that some Fardrivers have a label for Cruise/Park function. Can you explain how park function is engaged and also how to switch PINS for different functions on the app.
I finally decided I must make my repairs, to start can you tell me best way to match an exisiting controller, I know how from the out side. But as you know buy one then open and see what was sent.😮 board I want has heavy traces - strips of conductive material to increase current flow and effectientcy. I have the fiido T1 cargo where can I find a good controller? thanks
Your polarity is correct? if yes your MOSFETs must be shorted.. check resistance and continuity between Negative yellow , negative blue, negative green, and same with positive, there you can find your shorted mosfets
@@EVCustoms with the controller open everything is covered in resin, I can't even see the board but I just tested the continuity on all the terminals, it gives me some values but it doesn't sound it just beeps for a while between the negative and positive poles, should I buy other one? 🥲
This was so well done! I was going to produce a similar video but now I will just point to yours 👍 Subd for more, I'm a new content creator and just dropped a video on an undocumented Fardriver/Kunray problem. You seem very knowledgeable on these kits, and would love your feedback if you had a moment!
Hii there,I have Park/Cruise button in right combination switch of my ev bike,It has 2 wires coming into the connector- Blue and Blue+White wire. 3 wires for 3 speed and one black(GND) wire.How do i activate Park/cruise mode button functionality,should i connect blue to Blue of Fardriver cruise wire.I am confused please help.
What wire goes to the pos and what goes to the neg on the switch/button for reverse?
Will you make a video featuring boost on the fardriver learning board?
Super explain as always. Highly Appreciate
Thanks a ton
what can you tell me why the front engine after changing the hall sensor takes too much ampere code for the bottom engine
@@EVCustomscan you tell me whay my 1 motor after i change the hall sensors is taking to much ampers the 2 motor takes 1.5 ampers but 1 motor is taking 10 ampers
Awesome video! I would love to see a video of you tuning the Fardriver.
Is it possible to use 3speed button instead of a switch? I want to use a fardriver 72450 but my bike has a speed button
Thanks
Great instructional video. I noticed that some Fardrivers have a label for Cruise/Park function. Can you explain how park function is engaged and also how to switch PINS for different functions on the app.
Hello friend.. have many half-made videos on my list and i don't have free time for fardriver short videos, it will take quite long time friend...
But you don't say how many volts the controller voltage input is like is 12 volts or do I put it the same as the battery or do I need a step-down
What wire is for region?
I finally decided I must make my repairs, to
start can you tell me best way to match an exisiting controller, I know how from the out side. But as you know buy one
then open and see what was sent.😮 board I want has heavy
traces - strips of conductive material to increase current flow and effectientcy.
I have the fiido T1 cargo where can I find a good controller?
thanks
Hi friend, I tested the battery terminals on my fardriver (pos and neg) and there seems to be continuity, is it normal or is it bad?
The continuity tha you see is thrue controller capacitor's.. it is new?
@@EVCustoms Yes, is the first time that I tried to power it with 72v
and the BMS of my battery cuts the current because it detects a short circuit.
Your polarity is correct? if yes your MOSFETs must be shorted.. check resistance and continuity between Negative yellow , negative blue, negative green, and same with positive, there you can find your shorted mosfets
@@EVCustoms with the controller open everything is covered in resin, I can't even see the board
but I just tested the continuity on all the terminals, it gives me some values but it doesn't sound
it just beeps for a while between the negative and positive poles, should I buy other one? 🥲
If is beeping for some seconds its ok, is phase capacitors, it must be ok from mosfet side.. are you sure about your battery?
The entire connection run on 5 volts?
Control system running on 5V
thank you
This was so well done! I was going to produce a similar video but now I will just point to yours 👍 Subd for more, I'm a new content creator and just dropped a video on an undocumented Fardriver/Kunray problem. You seem very knowledgeable on these kits, and would love your feedback if you had a moment!
Hello mate.. nice channel by the way... i just seen your video about FarDriver issue.. ;)
Thank you!! @@EVCustoms
Hii there,I have Park/Cruise button in right combination switch of my ev bike,It has 2 wires coming into the connector- Blue and Blue+White wire. 3 wires for 3 speed and one black(GND) wire.How do i activate Park/cruise mode button functionality,should i connect blue to Blue of Fardriver cruise wire.I am confused please help.