Many people commenting "use grease, bread" etc. That method is useless if the bearing is not sealed or the cavity has an oil gallery etc. Thanks for the video, I finally removed a stubborn bearing today using this as a basis for a design.
It's also pretty useless if you actually try doing it, you'll probably just have spattered grease and be frustrated as you re-assess your pullers to make something else work.
Make inner shims of various thicknesses to accommodate different inner race IDs; make the basic tool to pull the smallest bearing you wish to work with and add inner shims to work on the larger ones.
I shoot grease in the bearing cavity and use a punch or piece of stock ground to fit through I.D.. Hammer punch and hydraulic pressure removes the bearing, works every time. Thank you for posting this, good tool making skills.
i had the same problem on a car gearbox , you can force the bearing out with well soaked bread !! push the bread into the centre of the bearing find a quite good fit bar and hammer it in thus forcing the soaked bread behind the bearing and forcing it out amazing but it works i think there are videos on youtube about it
@@snoyes34231 Yup. I usually use silicone wax, as it's much easier to clean up after. This guy's idea isn't bad (I've done similar, but not for blind bearings). However, you'd have to make one for every size bearing shaft you could come in contact with. I bet it took him the better part of a full day's work to complete this. The bread or silicone trick would've had you done and moving on w/in ~5min.
great tool build its amazing with the tools wich you are using dont get me wrong wich are home made and very well made you accomplished making a very totally funktional tool. i am a machinist and have a lathe and mill and i really dont think i could make that tool any better than you for funktionability.
Shove bread or silicone wax into the bearing's hollow shaft. Take a piece of the appropriate sized shaft steel and pound it into the hole. The bread/silicone will force the bearing out (hydraulic pressure). You're done in under 5min, you didn't have to make a custom tool, and it'll work for almost any sized bearing.
Great idea but if have larger or smaller bearings might not work same.. a small slide hammer kit with the 2 hook style is what I have from Cornwell tools.. just the lip of the hooks get mangled or bent kinda easy.. iv had to warranty it twice
Instead of taking help with heavy tools to make bearing puller.... You can remove bearing in cheaper way.... Just break candle in small pieces and fill in middle hole of bearing and tap with same size of bearing hole bolt which can easily move around in bearing hole tap tap until bearing come out.... But it work when other side of bearing cover with part surface
Lol, whatever. Get started on making that tool and I'll have the bearing out before you have your stock centered to start turning because i was able to find a stick and some rags and some grease.
4 hour to build an only use once in a lifetime, very specific to one size bearing , what if the next one doesn't have clearance for the puller? grease,, a punch and hammer would have had that bearing out before a guy would have finished taking measurements for tool design
hmmmm. just take short pieces of rods at different diameter. split one end. insert the spit end in the blind hole bearing and jamm at the splitt a wedge. Then pull, or hammer out. I have to admit you did a nice tool that you can use for 1000 projects...
Excelente.en México en el taller donde yo trabajé utilizamos un espárrago de media pulgada o una barra roscada de cada punta y se le coloca un casquillo con rosca interior de media pulgada y en la inferior Se hace una rosca interior para colocarles un tornillo de media pulgada y a cada tornillo se le solda un tornillo de diferentes diámetros y es un excelente extractor de pernos de fijación
Questo giocattolo è buono per smontare i cuscinetti della macchinina elettrica del bambino che gioca in giardino……vieni a smontare uno di quei cuscinetti grippati che smonto io poi me lo ridici le bestemmie che ci tiri😂😂😂😂😂😂😂😅😅😅😅
Fun to watch but way too much work. They sell tooling for exactly this problem. 90% of the time it takes about 10 minutes to get that out. You just can't charge a customer $300 to pull a bearing
Many people commenting "use grease, bread" etc.
That method is useless if the bearing is not sealed or the cavity has an oil gallery etc.
Thanks for the video, I finally removed a stubborn bearing today using this as a basis for a design.
It's also pretty useless if you actually try doing it, you'll probably just have spattered grease and be frustrated as you re-assess your pullers to make something else work.
Congratulations, great job.
Great Solution, Design seems specific for particular size. It is dificult to use for various size bearings to pulled out.
Make inner shims of various thicknesses to accommodate different inner race IDs; make the basic tool to pull the smallest bearing you wish to work with and add inner shims to work on the larger ones.
I shoot grease in the bearing cavity and use a punch or piece of stock ground to fit through I.D.. Hammer punch and hydraulic pressure removes the bearing, works every time. Thank you for posting this, good tool making skills.
i had the same problem on a car gearbox , you can force the bearing out with well soaked bread !! push the bread into the centre of the bearing find a quite good fit bar and hammer it in thus forcing the soaked bread behind the bearing and forcing it out amazing but it works i think there are videos on youtube about it
😲
@@snoyes34231 Yup. I usually use silicone wax, as it's much easier to clean up after. This guy's idea isn't bad (I've done similar, but not for blind bearings). However, you'd have to make one for every size bearing shaft you could come in contact with. I bet it took him the better part of a full day's work to complete this. The bread or silicone trick would've had you done and moving on w/in ~5min.
😊😊
Good job👌👍👏.. Thats a brilliant idea💭...
حل ممتاز 👍ولاكن☝️معقد بعض الشئ..ومع ذالك شكرا لمجهودك 🙋
great tool build its amazing with the tools wich you are using dont get me wrong wich are home made and very well made you accomplished making a very totally funktional tool. i am a machinist and have a lathe and mill and i really dont think i could make that tool any better than you for funktionability.
Always enough space under the bearing to allow the puller jaws to grip!
Cute!
Yeah convenient.
Anyway you can just use bread. No gap needed under the bearing.
@@wizrom3046 Or heavy grease and a wooden dowel, like I've done in my Shop for years.
@@regsparkes6507 I like silicone wax (easy to clean up), but, yes, simple to do when you employ hydraulic pressure.
Nice puller. We shared this video on our homemade tools forum this week 😎
Good "lathe" - angle grinder post. Good idea
That's genius!!!👏👏👏
🎉🎉🎉 فكره رائعه بأدوات بسيطه اشغل البال بالمحال 4:51
Great idea!! Nice work!
jjjiii8iiii8888888i8i8i8i8888888888i888888i888i8888888i88iii88888i88i888i8i8888888i88888888i888i888i88888888i8888888888888888888888888888i888i88888888i88888888i88888888
i88
88
88
888
Thank you for this video :)
Ah yes, let me head downstairs to my fully equipped wood/metal shop
Very clever design!
Simple and i need that puller. I will developmenting for big size . Thank you for your idea. Regards
Shove bread or silicone wax into the bearing's hollow shaft. Take a piece of the appropriate sized shaft steel and pound it into the hole. The bread/silicone will force the bearing out (hydraulic pressure). You're done in under 5min, you didn't have to make a custom tool, and it'll work for almost any sized bearing.
They sell tooling to pull any size bearing. Grant you it was fun to watch but way too much work
Great idea but if have larger or smaller bearings might not work same.. a small slide hammer kit with the 2 hook style is what I have from Cornwell tools.. just the lip of the hooks get mangled or bent kinda easy.. iv had to warranty it twice
Nice DIY work.
Really great 👍
de que material es? que acero usaste?
Ķ
Понравился способ обработки вала. Надо воспользоваться.
Well done, I like it.
Instead of taking help with heavy tools to make bearing puller.... You can remove bearing in cheaper way.... Just break candle in small pieces and fill in middle hole of bearing and tap with same size of bearing hole bolt which can easily move around in bearing hole tap tap until bearing come out.... But it work when other side of bearing cover with part surface
Amazing tool👍
It’s a wonderful idea! Nice and simple work. Your sliding angle grinder is so good. Have put any video about it? If so please send link
Sar, bike ki baring nikal sakte he
Super👌
Projects like these are for retired guys with time on their hands and fully equipped shops.
Amazing mr👍👍 good job 👍👍👍
Very clever!
That's a good one!!!
¡Esta herramienta es muy profesional!😉👍👍👍👍
On certain applications i had to make a bearing pusher to remove them.
Good job👍
Good luck sir 🎉
Hi friend which country are you from
I used bread to remove my pilot bearing in my Nova
next up, Make a crankshaft / DIY diesel crankshaft
Brilliant!
Aa pullar lena he
Very nice
Amazing❤
Very good
Lol, whatever. Get started on making that tool and I'll have the bearing out before you have your stock centered to start turning because i was able to find a stick and some rags and some grease.
What if the bearing is not sealed or there is an oil gallery behind the bearing?
My dad was a machinist by trade, he would have thoroughly enjoyed watching this.
Sir/ paano mag order sa iyo nyan? Magkano kaya yung tatlong puller? Salamat po.
சிறப்பு 👍 💐
Good work
4 hour to build an only use once in a lifetime, very specific to one size bearing , what if the next one doesn't have clearance for the puller? grease,, a punch and hammer would have had that bearing out before a guy would have finished taking measurements for tool design
Good video for watch
Nice
hmmmm. just take short pieces of rods at different diameter. split one end. insert the spit end in the blind hole bearing and jamm at the splitt a wedge. Then pull, or hammer out. I have to admit you did a nice tool that you can use for 1000 projects...
BTW: WD40 also helps.
I hope you wear a good dust mask. Thats alot of metal particle and grinder dust for one project.
И под каждый размнр делать снова? -Кусок хлеба поможет изъять подшипник.😂
0:48 OMG xD just take this rod to a man with a lathe and he will do this for a beer.
Si utilizamos tu criterio mejor vámonos a la ferretería.y se terminan los problemas.
Excelente.en México en el taller donde yo trabajé utilizamos un espárrago de media pulgada o una barra roscada de cada punta y se le coloca un casquillo con rosca interior de media pulgada y en la inferior Se hace una rosca interior para colocarles un tornillo de media pulgada y a cada tornillo se le solda un tornillo de diferentes diámetros y es un excelente extractor de pernos de fijación
So you're saying I don't have to pack my pilot bearing full of bread to get it out
Price please sir
Этот съемник только под один фиксированный внутренний диаметр подшипника.
I don't have all the tools you have to make this........
Only homemade if you use tools that an every day person has not a full workshop
Uma ideia show de bola
Mujhe yaisa tool chahiye
genius
damn! that's good.
Я тоже самое делаю обычным анкером.
Good
This is so easy to make, it only cost me $1000 in materials and equipment 👍……………….Hang on, I could of just bought one for $20 🤔
Use proper tools.puller is available in the market and very cheap.dont lost the time and risk.
Mroźna prościej 😁😁🤣🤣
Questo giocattolo è buono per smontare i cuscinetti della macchinina elettrica del bambino che gioca in giardino……vieni a smontare uno di quei cuscinetti grippati che smonto io poi me lo ridici le bestemmie che ci tiri😂😂😂😂😂😂😂😅😅😅😅
Es una broma nooo tanto laburo para sacar rulemanes en madera
But you can buy a complete set for a wide range of bearing sizes for only £27 and they work so much better than this.
I dunno, the 2 times I needed a blind hole puller, I went down to Auto Zone and borrowed one for free. Worked great.
Красафчик
Fun to watch but way too much work. They sell tooling for exactly this problem. 90% of the time it takes about 10 minutes to get that out. You just can't charge a customer $300 to pull a bearing
Sure, go out and buy thousands of dollars worth of equipment so that you can build a 100 dollar tool.
Smart way to save money.
лайк я зробив з ресори
👍👏👏👏
Ótimo invento muito útil!!!
...or just rent the complete set of various sizes for free down at the Vato Zone 🤷♂️
KUCH BOLECH NA?
KUCH CHALECH NA,?
MAZI RADHA RUSLI KA?
ISKA मतलब
मैं मुका vdo बिलकूल भी पसंद नाही करता हू,,
इसके बनाने में ज्यादा खर्चा आ जायेगा बहुत लेंदी प्रक्रिया है
👍👍👍👍
Mantap
Innenlager Abzieher versch. Größen gibt's für kleines Geld zu Kaufen.
BASTLER bauen es lieber selbst.
Depende el dinero que cada uno tenga, si puedes apañar materiales gratis, lo veo bien como lo hace
👍☕💪
Troppo lavoro.meglio comperarlo gia fatto
Only for one size😂😂
i want beans 1 piece
Inner bearing remover, good decision, bad idea, it will damage bearings.
Perhaps the reason it is being removed is because it’s being replaced.🤷♂️
In which case it would be way easier to just cut the bearing.
@@johndough9187coupé le roulement avec quoi quand il n'y a pas d'accès
👍
ŚCIĄGACZE MAMY GŁĄBIE
Бля, чел ты в каком веке живёшь. Инструмент есть, съёмник купить не можешь? Ну бля зашквар.
Маладцы
Jesus....just buy the friggin' tool.......
Show
Asambal karma ph karo
BULL SHIT JUST PURCHASE THE TOOL