ฝัง
- เผยแพร่เมื่อ 6 ธ.ค. 2019
- Hey everyone! In part 1 of this video series I’m going to go over the parts and tools necessary to replace the clutch on a Honda S2000.
Follow me on Instagram for more Honda S2000 content: / diyguystv
Please consider using the links below to purchase tools in order to support my work.
Parts necessary:
- Friction Disc (22200-PCX-055)
- Pressure Plate (22300-PCX-015)
- Release Bearing (22810-PCY-003)
- Pilot Bearing (91006-PCX-008)
- Flywheel (22100-PCX-005)
Tools necessary:
- Honda High Temp Urea Grease (amzn.to/350pXpx)
- Clutch Alignment Tool (amzn.to/3512NPS)
- Extension Drive Bar Set (amzn.to/2YsXIxp)
- 12 Point Socket Set (amzn.to/34595gd)
- Universal Joint Set (amzn.to/2YrPTHY)
Tools Recommended:
- Cordless Impact Gun (amzn.to/33YuI1z)
- Ratcheting Wrench Set (amzn.to/2P0USwv) - ยานยนต์และพาหนะ
This channel will keep many S2000s on the road for years to come.
Thanks for sharing! super helpful! gonna watch all of your s2k videos
Thank you so much! Just finished my clutch replacement very helpfull.
This is awesome. I have been waiting for this mini series. My clutch on MY03 is starting to slip. Thanks for the hard work!
You’re welcome!
Great video as always boss! I’m gonna get some longer extensions thanks to you! I will be doing the clutch in mine in the upcoming weeks
Thanks NAUS, good luck with the clutch job. It will be quite an experience haha
Great video can’t wait for the next video
Thanks for this awesome descriptive video !
The s2k was my first clutch job and honesty it was super easy just very time consuming like you stated. The factory service manual was my friend
The factory service manual is pretty solid. Its a little vague about some things and doesn't illustrate technique so I'm hoping these videos will complement the factory service manual.
I installed a ebay clutch kit in my s2000 this past summer (it was $200 for everything) i installed it myself and i luckily didnt run into any trouble because like you i was prepared before my repair. I do agree with you use oem parts because the one in my car now has clutch buzz like crazy otherwise its okay and functional. I would only recommend it to anyone that cant afford anything better.
Also i would like to add you're right about the premature failure with the bearings. I havnt had a problem with the ebay ones yet... but if sure its going to be the first thing to fail they looked and felt the cheapest from the kit i got
awesome info man!
As always 👌 most excellent!
Thank you very much for the video.
This video is amazing
Finally! Nicely done, Jason!
Excellent videos - thanks so much for putting this together. I need to decide whether to purchase a flywheel for my 2003 ap1 clutch job. Actually, I am assembling the oem parts to do the job in anticipation of the possibility that the parts may be discontinued down the road. I'm confident that my low mileage street driven ap1 will need a new clutch down the road sooner rather than later during my ownership. Is it fair to say that the old flywheel will most likely be serviceable where I am replacing a worn out oem clutch for the first time, (ie. no after market clutch parts have ever been used)? When the time comes for me the situation will be that the original oem parts are just worn out and sticky etc.- probably the real problem likely be that the slider for the clutch release bearing is dry and worn - that is what I expect will force me to pull the transmission off and when I do that I will put in a complete new clutch.
You can resurface the OEM flywheel no problem. I’ve done it every time.
One other thing to add. Spoon makes ridged collars that go in-between the subframe and frame rails. They keep the subframe perfectly straight in the car. Yes there is movement and will throw out you alignment. Have an alignment check done after.
I plan to add spoon rigid collars to my car soon and will make a DIY video for that but I don't think it is really relevant to the clutch job.
The subframe typically ends up shifting on cars that are tracked and pushed to the absolute limit. For this reason I don't really recommend spoon rigid collars for street cars.
Additionally, spoon rigid collars are only helpful after your car has been properly aligned after installation of the spoon rigid collars. So in this case your alignment may change whether or not you install rigid collars.
Thanks for the set of videos! I know higher is always better when it comes to jacking the car up, but do you have any idea how high yours was with a respective reference point?
I don’t but it was close to the highest your typical 3 ton jackstands would go.
Find forget about the slide for the throw out bearing. They usually worn pretty bad. Also there are a few parts for fork I would recommend replacing also.
I know LHT likes to make a big deal about how they always replace the clutch release bearing guide but I am skeptical as to necessary it is to replace it which is why I omitted it from this video. My clutch release bearing guide had 150K miles and seemed to be in fine shape. I will add a note to the description however since it is worth mentioning.
I know the clutch fork develops a small amount of play but again even at 150K miles with some play in the clutch fork my new clutch feels amazing. I don't see how a minute amount of clutch fork play would really be worth replacing.
is "ACT 600355 XACT Streetlite Flywheel " any good for Honda S2000 AP1. I am going to install it. Or should I resurface the original Honda S2000 flywheel
I think both are good options
Did this by my self... and I can tell you I wish I had taken it to the stealership... bu my pride got in the way lol
It is definitely pretty overwhelming when you’re just reading s2ki or following the shop manual since they are both somewhat vague. I’ll be sure to cover a lot of tips and tricks for the more difficult situations.
Did you reuse the Flywheel and pressure plate bolts? If so any thread locker etc.
Reused all bolts. No thread locker required if torqued correctly.
My clutch pedal feel very soft after my clutch replacement. Is it normal?
I've tried bleeding the clutch system still feel soft. Then thought it could be the master clutch cylinder, changed and bleed again got all the air out but still feel the same.
The clutch was perfectly fine on the day doing my clutch replacement. What could it possibly be? Thanks in advance
I have a 2000 honda s2000 with only 52k on it. The clutch buzz is bothering me! Would I be able to get rid it of completely with these 5 honda oem parts? Thank you.
Yes. I don’t even think you could buy a friction disc that would have clutch buzz anymore.
do these oem flywheel parts fit my 05 s2000?
Yes all years
Literally have the car up and about to do this job.
Woot! Should have the rest of the videos up by tonight.
Awesome!
I have an important question, you said that at least a 36" extension is needed to get to the transmission bolts but the link you provided only goes up to a 30" extension?
You can combine multiple parts of the set to create a long extension. Anyhow, I believe I used the 30” so 36 might be a little conservative depending on what sockets/universal joint you are using.
@@DIYGuysvideo Ok thanks man I really appreciate it!
what about replacing the rear main seal?
Should be done on an as needed basis. Personally never seen a leaking rear main seal.
Thanks for the video. Where did you order your parts?
eBay. However if I were to do it again I may buy the kit made by SACHS sold on rock auto.
DIYGuys thanks. SACHS friction disk looks exactly like OE. I wonder if it performs like OE.
There is a thread about this on s2ki: www.s2ki.com/forums/s2000-under-hood-22/cheap-oem-honda-clutch-option-sachs-honda-fcc-nachi-etc-1182002/
I think the conclusion was that the part numbers are slightly different but the quality is probably the same.
@@DIYGuysvideo which kit is that specifically? There is a lot of them but I can't seem to find it
www.ebay.com/itm/Clutch-Kit-Sachs-K70310-01-fits-2004-Honda-S2000-2-2L-L4-/133662053578?_trksid=p2349624.m46890.l49292
I thought it was the oem clutches that buzz....
Older versions of the OEM clutch that you can no longer buy yeah.
@@DIYGuysvideo ohhhhh OK cool.
@@DIYGuysvideo i've heard of many people who had the newer part number clutch plates that still have clutch buzz. it's more of a 50/50 thing. Meanwhile many others have had amazing luck with exedy "oem" replacement clutches.
04+ friction discs don’t buzz. Exedy clutches might not buzz but they are garbage. I have broken one myself.