Dude I'm so excited for this. I wish I could come over and work on this with you. I've also just done a longer stretch bar. Mine is about 15inches though 😬. Id pay for content dude
This is awesome!!! I hope you do the rear disc brake conversion and the 171cc setup. Man I wish I lived closer to you so I could ride by and get sneak peeks of the build.
Awesome! A new build. Can’t wait to see how it comes out. I recently picked me up a project and swapped a 150cc gy6 in. Need a few more things soon and I’ll be ordering those from TRS. And happy Easter to you and your family!
Nice project and Good content, In regards to the 45 pitch on the slide carb, think the angle will be effected when the wheel and weight are on the bike when the frame sits closer to the shock mount. Might not be the best idea but when you cut the manifold, you could do an angle cut, weld in the bolt holes then re-drill, to change the angle of the holes to match. Which should level things off whilst bringing it lower.
Thank you. I have since tightened it all up and didn’t have to go that far into it for it to work. Appreciate the advice but I was able to make it for a lot easier fortunately for me. Thanks again.
I’m so new to the ruckus game, but I am absolutely in love with these things. Gonna get one this summer. I have a question. Are these motors complete? Or in need of upgrades? I’d like to comfortably do 60-70 with traffic.
The stock motor will not go close to that mph. You will need to do a gy6 swap and some mods to cruise at that speed. Looking to invest about 2500 into it to make that happen.
Awesome setup so far. I have a question, I’m doing a build and have the same mount as you’re using and am wanting to do a 14-15” stretch as well. Did you have to notch out the rear frame if you didn’t shorten by 2”?
Awesome vid brother. I see your vision. 95% of my parts came from the ruck shop as well😂. My ruck is also custom built to my vision. Center shock setup, 4140 chromoly tubing to reinforce the back half of the frame, TRS aluminum gas tank, love the flat clean surface. Can’t wait for the next vid.
Yea no problem, I know you have a lot on your plate. I’m ready when you’re ready. I’m in Lakeland so it’s a hop and skip to your location. My neighbor Steven Straw mentioned to me bout the ruck shop is trying to organize a ride?
@@burnoutbobby ha! Nah, I sold my old one but now I wish I still had it. That's how I found yer channel, lookin to get back in the scene. 🤘y'all have a badass day🤘🍻🤘no limits🤘
Hey Bobby nice. Minnie horse Bobby got a qs. Got a pwk20 mm I wanna put it on my pmz22 50cc gy6 maddog dnt have the throttle cable can I use or fab the throttle cable. The Madd dog uses
@@burnoutbobby I’m currently at 48mph flat wondering if there’s something I’m missing for the extra 2mph -type 1 airbox delete, Yoshimura exhaust 38/82 jets, decompression tube, polini variator using extra rollers that came with that were labeled “6,9” , Ncy cdi I’m 145 pounds. Any ideas?
@@burnoutbobby I had a feeling you knew someone to get it from. I've been searching for a front frame to do my build, but of course none of them have titles or vins
Ive got parts from each one of Everyone commenting here about it to help support the community, remember we are doing our build to meet with all the community to help us bring in the charity organization called Operation Combat Bike Saver To put in a charity garage in my area for my fellow veterans especially the ones suffering from ptsd.
@@burnoutbobby the parts are a little more rare but I'm positive they run gy6s on them. It's alot more to do as far as getting the mount built for it if you're going to do something custom which being you I know you will. I think you'd make one badass Honda Bite and it takes essentially a bicycle seat with almost the same style frame you build on your gy6 ruckus.
![เปิด อาณาจักร หมื่นล้าน "สาระตั้ม" l [Nickynachat]](http://i.ytimg.com/vi/3XE0nPF4YkQ/mqdefault.jpg)
Duuude! I’m digging that!! Should be super dope!
Thank you sir!
Whats up brother good to see you here as well
Good to see someone who really loves the culture. Can't wait to see this finished
Thank you. I appreciate it and love helping people out with these videos.
I'm glad to see the Ruckus scene keeps growing. I modded my first ruckus back in 06.
That’s awesome. It will continue to grow!
Dude I'm so excited for this. I wish I could come over and work on this with you. I've also just done a longer stretch bar. Mine is about 15inches though 😬. Id pay for content dude
My guy!
I am down the series! RDR is in! Love the builds!
Much appreciated! Love your builds as well.
Awsome job brother, we all have some serious builds all over the place on each one of our channels
This is awesome!!! I hope you do the rear disc brake conversion and the 171cc setup. Man I wish I lived closer to you so I could ride by and get sneak peeks of the build.
171 for sure. Not sure on rear disc yet
Awesome! A new build. Can’t wait to see how it comes out. I recently picked me up a project and swapped a 150cc gy6 in. Need a few more things soon and I’ll be ordering those from TRS. And happy Easter to you and your family!
Awesome! Thank you. Happy Easter to you and your family.
Nice project and Good content,
In regards to the 45 pitch on the slide carb, think the angle will be effected when the wheel and weight are on the bike when the frame sits closer to the shock mount.
Might not be the best idea but when you cut the manifold, you could do an angle cut, weld in the bolt holes then re-drill, to change the angle of the holes to match.
Which should level things off whilst bringing it lower.
Thank you. I have since tightened it all up and didn’t have to go that far into it for it to work. Appreciate the advice but I was able to make it for a lot easier fortunately for me. Thanks again.
I’m so new to the ruckus game, but I am absolutely in love with these things. Gonna get one this summer.
I have a question. Are these motors complete? Or in need of upgrades? I’d like to comfortably do 60-70 with traffic.
The stock motor will not go close to that mph. You will need to do a gy6 swap and some mods to cruise at that speed. Looking to invest about 2500 into it to make that happen.
Awesome setup so far. I have a question, I’m doing a build and have the same mount as you’re using and am wanting to do a 14-15” stretch as well. Did you have to notch out the rear frame if you didn’t shorten by 2”?
The only thing I had to do was notch out the mount for that pitch.
Awesome vid brother. I see your vision. 95% of my parts came from the ruck shop as well😂. My ruck is also custom built to my vision. Center shock setup, 4140 chromoly tubing to reinforce the back half of the frame, TRS aluminum gas tank, love the flat clean surface. Can’t wait for the next vid.
Thank you. Saw your other message. I’ll get with you soon!
Yea no problem, I know you have a lot on your plate. I’m ready when you’re ready. I’m in Lakeland so it’s a hop and skip to your location. My neighbor Steven Straw mentioned to me bout the ruck shop is trying to organize a ride?
Not the shop but just a couple of the employees might just do an afternoon ride one weekend.
Awsome looking forward to the new series. Quick question. I have sliders. What is the best for quick response and high end speed
Thank you
That’s an open question really. It’s all based off your weight/mph/ rpm you are at. Then you go from there.
I got a set of that under cowl in carbon but because I have the rear sets it won’t fit because of hot it hugs the frame and I’m afraid to cut it lol.
Yeah I was going to say you gotta cut it
Im just about decided to buy another ruckus too 🤘🍻🤘
Starting a collection bahah
@@burnoutbobby ha! Nah, I sold my old one but now I wish I still had it. That's how I found yer channel, lookin to get back in the scene. 🤘y'all have a badass day🤘🍻🤘no limits🤘
Hopefully you’ll be back in the game soon. Thank you
@@burnoutbobby
🤘woooooooooooooooooooo🤘
Where were the front frame side covers from and if you can give the price of them
I got them from my buddy koyo. I don’t remember the price. I want to say 130 and 90 to ship them. It’s probably more now as everything has gone up.
Hey Bobby nice. Minnie horse Bobby got a qs. Got a pwk20 mm I wanna put it on my pmz22 50cc gy6 maddog dnt have the throttle cable can I use or fab the throttle cable. The Madd dog uses
I wouldn’t. I’d just get a pwk cable since they are cheap.
@@burnoutbobby I'll order one from your shop it's the ruckus shop. Correct
The ruck shop. Yes sir.
Curious to know if you ever got the GET motor to go 50.
Yeah it does 50 with the stage 2 all day. Especially with fresh healthy motors.
@@burnoutbobby I’m currently at 48mph flat wondering if there’s something I’m missing for the extra 2mph
-type 1 airbox delete, Yoshimura exhaust 38/82 jets, decompression tube, polini variator using extra rollers that came with that were labeled “6,9” , Ncy cdi
I’m 145 pounds. Any ideas?
@@alexhernandez8127 tvr intake. The type one isn’t performance based like the tvr
@@burnoutbobby shoot, I didn’t realize that. looks like I’ll have to order it. I appreciate it!
@@alexhernandez8127 that’s usually the formula for me. You’re close enough to it!
Where did you get the frame from and did you get a title with it?
I bought the front frame with title off a buddy. The rear frame I ordered from Honda then modified myself.
@@burnoutbobby I had a feeling you knew someone to get it from. I've been searching for a front frame to do my build, but of course none of them have titles or vins
Yeah it took me about 3 months to get ahold of one.
@@burnoutbobby dang. I search on and off every couple of weeks and haven't found anything. Damn unicorns is what they are. Haha
Yeah they come and go. It’s always a battle. Lol
Hows the build coming along?
It’s not lol. Waiting on paint now for 5 weeks. I got everything ready but all the parts I shipped out for paint
Ive got parts from each one of Everyone commenting here about it to help support the community, remember we are doing our build to meet with all the community to help us bring in the charity organization called
Operation Combat Bike Saver
To put in a charity garage in my area for my fellow veterans especially the ones suffering from ptsd.
Thats amazing.
Where you purchase the side covers?
Japan
Website?
Wasn’t a website. It was a friend of mine who had them in Japan.
Can you make that a manual ?
You can make anything happen with a welder and cnc shop.
Nice Video as usual
Thank you sir!
Why don't you set your sights on a Honda bite gy6 build. Looks more of your style with that wicked seat design you come up with
Something to look into !
@@burnoutbobby the parts are a little more rare but I'm positive they run gy6s on them. It's alot more to do as far as getting the mount built for it if you're going to do something custom which being you I know you will. I think you'd make one badass Honda Bite and it takes essentially a bicycle seat with almost the same style frame you build on your gy6 ruckus.
I’ll start reaching out to my connects in Japan. They can get me oem parts for the bite. Then I can work from there
@@burnoutbobby hook me up with the contacts. I need some parts myself lol💜
For sure. His name is koyo ito
Hell no I'm not paying to watch you build your Ruckus
Hahahaha oh man.