Thank you very much! I don't use my printer often, but for the last few years, it's been printing dirty. I followed your steps here, and it's printing like new!
A+ video! For anyone with trouble removing the wire clip: I had to use pliers to firmly pull out the wire connector. It was too tight to remove with fingers. No damages.
Top, hab nach einem anderen Video nur das mit der Alufolie gemacht, was nichts gebracht hat. Aber der Hinweis mit den Zählerständen zurücksetzen war GOLD WERT!!!!!! DANKE
Geat video and explanation thanks. I had a transfer belt fault on a CLX-3305. Completly taking apart as per your second half of video and cleaning has solved the problem👍 the only different thing I did was fitting the side springs before the outer cover was reftted. Acess to them was then easier.
Excellent informative clear instructions. My printer had been fine until I needed to replace the black toner with a new one and the next print was awful quality with faded strips. Followed your instructions and felt very comfortable with my execution of the process but unfortunately made no difference to the faded bits. Could it be my new black toner cartridge?
Fantastic tutorial - thanks a lot for this! What is the grey dust I found in my printer? I have a Samsung C460FW - in this model you need to remove the transfer belt to the front.
Thanks for the clip, very helpful, I replaced the transfer belt with a new one (Samsung) however the Status light continued to flash any ideas? Thanks again
This procedure will require going into the Tech menu to reset the counter for Transfer Belt (there are other TH-cam videos on how to do this depending on the model, but it essentially a specific sequence of key presses on the controls: the display will read Tech menu if you are successful. For the printer in this video without keypad, the sequence is Menu, Back, Left, Right, OK, Stop/Clear, Menu. The C460 with a keypad uses Menu, #, 1,9,3,4, Menu. Once in Tech Menu, then go to Data Setup, then Clear Count (for the specific part you have replaced)). The mainboard doesn't "know" that the Transfer Belt (or any other consumable part) has been changed: resetting the counter is the only way to tell it you have completed the procedure. If you get error messages on any of these other "Consumables" and/or the Status light continues red/message appears you need to reset any of these parts, the Tech Menu is the only way to do this after you change out the part. Important: only change out parts once you have pulled the plug. Hot-swapping parts with the unit powered on may create problems with locking in error messages and may damage the mainboard processor.
CLP-315 with transfer belt not being wiped. I did clean it and disasembled just like in the video. The wiper has two rubber parts that do the wiping. The bigger one came loose when I tried cleaning it properly however. I cannot find a replacement part. Do I need a whole unit or will just the wiper fix my issues? It seems like the wiper does not take off all the powder left on the belt for some reason.
Hi great video. I have the same printer. I bought black toner but it is not original - they promissed it would be just as good as the original. Now I am not sure why the black color is weak when I print. Would it help to maintain the printer (maybe I did something wrong when I mounted the black cartridge) or is the problem that the toner is not original. It would be nice to know before I start maintainance. Thank you in advace. Hope the spelling is ok.
I think there is nothing wrong mounting the cartridge. Probably the toner cartridge is defective but the problem could be the drum unit too. The compatible cartridge are often good quality
Hi, this video has been most helpful. Upon cleaning the transfer belt, it has started to make very loud screeching noises when calibrating and printing. What can I do to solve this issue?
The right plastic lever shown you opening from the minute 1:18 was suddenly fell down of my printer, I tried to return it back but couldn't know how, any help?
Great video. I'm sure the ITB for a Samsung CLP-315 isn't very different. Does the belt itself ever wear out? The symptom is a blurry line maybe 6-10 mm wide across that page--sometimes yellow toner, sometimes black. Samsung literature says to replace the belt assembly. Is the real problem likely to be the wiper blade, or that the belt itself is worn out?
Grazie, Signore Viandant. I've found that replacement ITB assemblies cost $US 65-$US 130. But replacement belts are $US 18-$US 20 from China and I now have one. I have a spare ITB assembly I can play with. I had one question, but now I have two: 1) Can I disassemble the assembly to the degree necessary to replace the belt? The Samsung repair manual suggest that this can only be done at the factory where special jigs are used. 2) Do you think that the wiper blade has worn in such a way as to damage the belt and would shorten the life of a new belt? Or perhaps that it's normal belt wear? (I realize that without seeing the blade both of us are just guessing.) I think I might go back to the China websites and see if the wiper blade is available. I love the CLP-315 and have used and used it. We also have a CLX-3175 (all-in-one). I have performed the special mods on both of these as described here: rumburg.org/printerhack/ . Don't try this on anything but a CLP-310 or 315 or CLX-3175. It takes advantage of a quirk in the firmware which was removed in later versions.
Hi, thanks for your informative video. I bought a new transfer belt and fitted it as per your instructions which went well. But, when I turned the printer back on the error message "prepare new transfer belt" still came on. Any suggestions? Thanks.
After replacing the unit, you still need to reset the counter of the printer, which is done in the Tech Setup. To enter it, the combination of keys varies depending on the printer model - and unfortunately, Samsung didn't make them public (but they can be found for some models around the internet and on YT).
I just replace the drum unit, a new cartridges toner, and the lights still blinking, all of them. I was wondering if you could get some solution to this problem. Thank you
There are no reset procedures. I think the problem are the chip. Are compatible cartridges? However Samsung make all they can to create problems to cartridges, even original ones
@@viandant5 the cartridges are compatible but not original and the image drum unit chip was already replaced. Could it be the transfer belt? Many thanks
hello, thanks for these, great videos! I have a question, I have a samsung 3305FN printer and it gives 2 errors: "replace ITB" and "replace fuser unit". I know there is a chip resetting method for drum unit by soldering in drum chip but I want to learn if there is a way to reset "ITB=image transfer belt" or "fuser unit" with some chip soldering or anything like that??
I figured it out - I missed replacing the screw that holds the black flat plastic part at the end near the wires. After installing the screw (which I now call the colour screw) the printer works perfectly - no more ghost images and bright colours. Thanks again for the video it was excellent!
Hello, thanks for the video, I followed the cleaning instructions, but I still have a problem, when sending more than 2 sheets of some document, I get a ghost print of the watermark of the previous sheet, when I disassemble the transfer cartridge I notice that has remains of toner with the previous printing on it, apparently it is not discarding them, any solution? greetings from Mexico
Hola Bernardo! has conseguido resolver el problema que mencionas? Me trajeron una impresora que hace exactamente lo que mencionas, un "fantasma" de la impresión, pero sólamente es en la siguiente página. y no existe un segundo fantasma...
@@victoraguilars.4281 hola, no pude resolverlo ya que no consegui otra unidad de transferencia para probar, lo que hace mi cliente es mandar a imprimir una hoja por una, y asi casi no sale el fantasma ya que el repuesto es costoso, va a esperar a que se le termine el toner para desechar el equipo.
Great Video!! Thanks a lot - I just exchanged the transfer belt! My printer now is printing again :-) However - the note on the little display "prepare for ne transfer belt" is still there. How can I "delete" or stop this message ...
i can't get the transfer unit to stick back up in its original position, which makes it impossible for me to put the waste cartridge back. you make it look so easy. any suggestions?
have a problem with my Samsung clp-365w. On power up it doesn't go through its usual warm up procedures. It is connected to the computer via usb. Removing the usb cable causes the conputer to sound so it knows it is disconnected from the computer. I think it is a hard wear problem with the printer itself. I have recently emptied the wast container. I worked after that but one morning after I powered up the printer all lights on the display came on steady and the printer didnt go through its usual warm up proceedures.
hello, good afternoon, my printer marks the entire sheet with a very dark background, they told me that the problem could be the tape, if the tape is cleaned with alcohol and the blade, I will solve the problem or I have to buy the complete new tape, thanks .
Hi! I have a CLX-3305W and up to date 2 servicemen failed to fix it! It printed well at the beginning, then more and more often the paper would jam but now when I start to print, it makes some noises (like something rolling inside), and then BEFORE it even takes a sheet of paper, it displays the same error message as before: "Paper Jam in Tray 1". What could be wrong? Oh, and I must say that in the past it used to make this squeaky noise (like an old hinge) when rolling the paper, it made this noise more and more often and now it doesn't even roll the paper. What to do?
Yes, I will try to do that. The paper is fresh from the box. But everything looks (to me at least, I'm unprofessional of course) like some roller just seized up, because the machine squeaked more and more while rolling the paper and now it doesn't attempt to roll the paper. As I understand it, the pickup roller is only for picking up the paper and then some second roller starts working?? I think maybe this second roller got dirty and that's why it seized up? Do you have any video where I could see how to properly disassemble the printer and locate this "second" roller? :) Thanks.
Unfortunately the problem persists, evidently some internal mechanism for rolling the paper has just seized up. BEFORE it even takes a sheet of paper, it displays the error message: "Paper Jam in Tray 1" but there is no jam anywhere (I checked every location). The printer is long past the warranty period so I want to disassemble it. The question is, which part is responsible for keeping the paper moving through the machine? This part is evidently broken or seized-up. Do you know?
sometime the cleaning is not enough, may be the rubber roller must be changed. there are gears in the side of the printer,may be one of them has a broken tooth
Hello, I have refilled on CLP365 only black powder on all cartridge by local toner for black printing ,now printer is working but sounding very bad , how can remove it , please suggest me how to remove the sound .
the bad sound may be related to the gears, the internal meshing bar or the toner powder. It's difficult to remove a bad noise, try lubricate all gears. If the cartridge is working I suggest you let it work
Salve Gianni, dopo aver seguito questa guida, ho rimesso tutto a posto ma la stampante adesso stampa solo ed esclusivamente in nero, i colori li salta, cosa potrei aver combinato? Strano perchè ho davvero fatto tutto abbastanza precisamente... Se hai qualche idea potresti rispondermi? Grazie
Stampa solo le parti in nero e i colori non li stampa? Non mi sembra un problema di cinghia di trasferimento, a meno che sia stata rimontata non correttamente e ora non sia parallela alle cartucce
@@viandant5 sebbene stampava male, comunque stampava sia nero che colori. Ho trovato questa guida, per la quale ti ringrazio, visto che lavoro come tecnico informatico ogni tanto metto mano anche a stampanti, prima volta che manovro una transfer belt, pulisco tutto sistemo tutto, rimetto su, provo e cosa succede? Stampa solo le parti in nero e salta completamente i colori! Da computer mi indica anche i livelli del toner presente ed è tutto nella norma… hai in mente cosa potrei aver danneggiato? Non è neppure mia, sono avvilito 😞
Purtroppo non mi è mai capitato, mi viene solo in mente che a lato della cinghia ci sono dei contatti, uno per ogni colore. Forse in qualche modo quei contatti sono difettosi o collegati male tranne il nero
@@viandant5 Per conoscenza sono tornato a riportarti che, ordinando una cinghia di trasferimento nuova, i colori sono tornati, quindi ho in qualche modo manomesso la cinghia precedente! (Però ho tirato un sospiro di sollievo, non ho danneggiato la stampante in sè)
By cleaning the transfer belt, do I still need to replace it? 'cuz my printer keeps showing a message that says "Prepare Transfer belt" it also says "Prepare Fuser soon", what do I do? and where can I find these parts to purchase?
The cleaning do not cancel the error message. prepare fuser soon means that you have to change the fuser unit soon. to buy the fuser search with google
viandant5 Are the parts different from one country to another? Suppliers in Saudi Arabia don’t provide these parts so I guess I’ll have to buy them from Amazon or eBay Will I have compatibility issues?
Buongiorno, è dovuto alla cinghia una linea verticale sulla stampa? composta da un assieme di vari colori e non completa da cima a fondo. Come posso intervenire. grazie
E' più probabile che sia il tamburo. Comunque controlla se la riga è presente anche sulla superficie di tamburo o sulla cinghia. In questo caso potrebbe essere la lama di pulizia
II think it's not an electonic problem to the main board, you should have an error message. It could be a mechanical problem, a gear or something not in the right position
This is the best tutorial ever! Samsung should pay you for this
Thank you so very much. You saved me time and money. People like you are the reason good moral values are still in place
I was having difficulty removing the transfer belt & decided to go online for help. Thanks for this video
this video is the only one giving precisely the steps. Thanks a lot
Thank you very much! I don't use my printer often, but for the last few years, it's been printing dirty. I followed your steps here, and it's printing like new!
Lots of fellow print-users praise Your video, today I join the congritation of happy print-users with a fixed and working transfer belt !!
Your video helped me detect why my transfer belt wasn't printing properly. Thank you.
happy to help you!
A+ video! For anyone with trouble removing the wire clip: I had to use pliers to firmly pull out the wire connector. It was too tight to remove with fingers. No damages.
Top, hab nach einem anderen Video nur das mit der Alufolie gemacht, was nichts gebracht hat. Aber der Hinweis mit den Zählerständen zurücksetzen war GOLD WERT!!!!!! DANKE
I have different model, but the basic principle is the same. Thanx for saving me buying new printer! Merry Christmas!
Exact same setup as my C430W. Thank you for taking the time to make and share this.
Geat video and explanation thanks. I had a transfer belt fault on a CLX-3305. Completly taking apart as per your second half of video and cleaning has solved the problem👍 the only different thing I did was fitting the side springs before the outer cover was reftted. Acess to them was then easier.
Just saved me from buying a new printer. Thank you!
That was the solution for my big problem about the yellow lines on the C460W- Great....Thank yu
Thanks, guy! You saved me a lot of tears.
Good Boy, i love you for this Video 😙
Finally I did make it. Thank you so much! I just used a qtip (cotton) in order to entirely clean the residue container.
Thanks so much for this. I was on the point of throwing out this printer for
Thank you so much. Your video helped save our problem
your instruction helped me a lot. Thank you.
solved my problem !! Thanks to you, my printer's working again. Awesome, keep it up!
Thanks a lot dear Viandant ! Very clear & detailed video
Excellent informative clear instructions. My printer had been fine until I needed to replace the black toner with a new one and the next print was awful quality with faded strips. Followed your instructions and felt very comfortable with my execution of the process but unfortunately made no difference to the faded bits. Could it be my new black toner cartridge?
Probably the cartridge is defective. The low quality is on all colors?
Thanks a lot! Very detailed video and nice breakdown of steps!
Muchas gracias por mostrar tu meticuloso trabajo!!
Fantastic tutorial - thanks a lot for this! What is the grey dust I found in my printer?
I have a Samsung C460FW - in this model you need to remove the transfer belt to the front.
probably it is toner powder
I thought I fixed my problem yesterday but I printed something this morning & my printing is still smudging. I'm going to try cleaning the drum today
MERCI pour cette superbe vidéo !
Muchas gracias me ayudo mucho tu video.
Thanks for this video 👍 You did an awesome job explaining step by step. I fixed my printer myself following the instructions and it works again.
Verstehe zwar kein englisch, muss ich bei diesem sehr gut erklärten Video auch nicht. Herzlichen Dank
There are the german subtitles
Super erklärt. Und bei meinem Drucker hats funktioniert. Danke
Excelente video... muy ilustrativo. Muchas gracias
Thank you for the video! It was interesting, this model has not yet analyzed the transfer belt!
Best reguards from Kiev
+vovanfun thank you, have a nice day
Great video, thanks👌
Tausend Dank für dieses Video!!! Echt super gemacht 😍
😎 SUUUUUPER- Thanks so much
Bravo ça marche. J'ai pu tout nettoyer 👍👌
Great instructions. Is there a replacement blade available?
may be on alibaba
@@viandant5 OH, thank you I didn't think about them.
Great tutorial
Great Tutorial, well done and thank you very much.
Thanks for the informative video, fellow human.
Interesting and useful! How can you know how much toner is left in each cartridge? thanks
The toner level? You can print the printer status th-cam.com/video/RqY9Z7bJJcE/w-d-xo.html
thanks, had to clean the transferbelt because there was some dirt on it causing white dots on black images :)
Thanks for the clip, very helpful, I replaced the transfer belt with a new one (Samsung) however the Status light continued to flash any ideas? Thanks again
I've no idea, the transfer belt counter shuld be resetted.
This procedure will require going into the Tech menu to reset the counter for Transfer Belt (there are other TH-cam videos on how to do this depending on the model, but it essentially a specific sequence of key presses on the controls: the display will read Tech menu if you are successful. For the printer in this video without keypad, the sequence is Menu, Back, Left, Right, OK, Stop/Clear, Menu. The C460 with a keypad uses Menu, #, 1,9,3,4, Menu. Once in Tech Menu, then go to Data Setup, then Clear Count (for the specific part you have replaced)). The mainboard doesn't "know" that the Transfer Belt (or any other consumable part) has been changed: resetting the counter is the only way to tell it you have completed the procedure. If you get error messages on any of these other "Consumables" and/or the Status light continues red/message appears you need to reset any of these parts, the Tech Menu is the only way to do this after you change out the part. Important: only change out parts once you have pulled the plug. Hot-swapping parts with the unit powered on may create problems with locking in error messages and may damage the mainboard processor.
CLP-315 with transfer belt not being wiped. I did clean it and disasembled just like in the video. The wiper has two rubber parts that do the wiping. The bigger one came loose when I tried cleaning it properly however. I cannot find a replacement part. Do I need a whole unit or will just the wiper fix my issues? It seems like the wiper does not take off all the powder left on the belt for some reason.
I think it's difficult to find the wiper blade. May be on aliexpress
Very useful video, my printer prints clean once more. Thx!
no hablo ingles pero estoy totalmente agradecida por su ayuda
There are spanish subtitles
Hi great video. I have the same printer. I bought black toner but it is not original - they promissed it would be just as good as the original. Now I am not sure why the black color is weak when I print. Would it help to maintain the printer (maybe I did something wrong when I mounted the black cartridge) or is the problem that the toner is not original. It would be nice to know before I start maintainance. Thank you in advace. Hope the spelling is ok.
I think there is nothing wrong mounting the cartridge. Probably the toner cartridge is defective but the problem could be the drum unit too. The compatible cartridge are often good quality
Very good video
Hi, this video has been most helpful. Upon cleaning the transfer belt, it has started to make very loud screeching noises when calibrating and printing. What can I do to solve this issue?
I the unit has been correctly assembled, I think you have to lubrificate the cleaning blade of the belt, or wait until the loud disappear
Thanks for your help... It was very nice...
Excellent video! Thank you so very much!
I’m having problems with paper jams using glossy vinyl paper. Will this help if I clean that part?
No, probably the problem are the feed rollers, or the fusers
The right plastic lever shown you opening from the minute 1:18 was suddenly fell down of my printer, I tried to return it back but couldn't know how, any help?
probably it's broken, try to reassemble the printer without that lever
THX 🙂
Gracias por compartir.
thank you so much!
Thks . it was very usefull for a 3170. it almost the same. now the printing are perfect.
Hi, do you have a video showing how to change the Fuser in a samsung Xpress C480FW please?
it's similar to samsung clp 320/360, in this channel there is a video
Great video. I'm sure the ITB for a Samsung CLP-315 isn't very different. Does the belt itself ever wear out? The symptom is a blurry line maybe 6-10 mm wide across that page--sometimes yellow toner, sometimes black. Samsung literature says to replace the belt assembly. Is the real problem likely to be the wiper blade, or that the belt itself is worn out?
probably the belt itself is worn, and the wiper blade is one of the causes
Grazie, Signore Viandant.
I've found that replacement ITB assemblies cost $US 65-$US 130. But replacement belts are $US 18-$US 20 from China and I now have one. I have a spare ITB assembly I can play with. I had one question, but now I have two:
1) Can I disassemble the assembly to the degree necessary to replace the belt? The Samsung repair manual suggest that this can only be done at the factory where special jigs are used.
2) Do you think that the wiper blade has worn in such a way as to damage the belt and would shorten the life of a new belt? Or perhaps that it's normal belt wear? (I realize that without seeing the blade both of us are just guessing.) I think I might go back to the China websites and see if the wiper blade is available.
I love the CLP-315 and have used and used it. We also have a CLX-3175 (all-in-one). I have performed the special mods on both of these as described here: rumburg.org/printerhack/ . Don't try this on anything but a CLP-310 or 315 or CLX-3175. It takes advantage of a quirk in the firmware which was removed in later versions.
I've have a video on how to disassemble the belt. I think the wiper blade is ok.
I think that hack will work only if you do not have a new firmare version.
It seems to work on all CLP-315 and CLX-3175. It will BRICK any newer models. This is why I keep maintaining my old ones.
Thanks a lot, Big help. When I need to made urgent print at wekend and my printer it does´nt work .
THANKS FOR HELP ! :-)
Should I still follow this video to try sort out the problem x
Hi, thanks for your informative video. I bought a new transfer belt and fitted it as per your instructions which went well. But, when I turned the printer back on the error message "prepare new transfer belt" still came on. Any suggestions? Thanks.
After replacing the unit, you still need to reset the counter of the printer, which is done in the Tech Setup. To enter it, the combination of keys varies depending on the printer model - and unfortunately, Samsung didn't make them public (but they can be found for some models around the internet and on YT).
@@MrSuicycle It's usually 1934 for most models
You helped me big time friend
I just replace the drum unit, a new cartridges toner, and the lights still blinking, all of them. I was wondering if you could get some solution to this problem. Thank you
There are no reset procedures. I think the problem are the chip. Are compatible cartridges? However Samsung make all they can to create problems to cartridges, even original ones
@@viandant5 the cartridges are compatible but not original and the image drum unit chip was already replaced. Could it be the transfer belt? Many thanks
@@marcelolobfig Yes, it could be the transfer belt. Check the printer folder to have more informations
hello, thanks for these, great videos! I have a question, I have a samsung 3305FN printer and it gives 2 errors: "replace ITB" and "replace fuser unit". I know there is a chip resetting method for drum unit by soldering in drum chip but I want to learn if there is a way to reset "ITB=image transfer belt" or "fuser unit" with some chip soldering or anything like that??
Thank you, I regret but I don't know any reset method for fuser or ITB
the reset chip is only for the toner/dv unit
Hallo, vielen Dank für das Video. Nach der Reinigung des Transfer Belt druckt der C480FW nur noch schwarz / weiss. Wo liegt der Fehler? Vielen Dank
Ich denke, das Problem sind die Druckereinstellungen
Também estou com este problema e não é a configuração 😭
I performed the cleaning process, but the printer won't print colour anymore - just black and white - any suggestions?
a cleaning process in a CLP-365? I think it's a problem of settings
I figured it out - I missed replacing the screw that holds the black flat plastic part at the end near the wires. After installing the screw (which I now call the colour screw) the printer works perfectly - no more ghost images and bright colours. Thanks again for the video it was excellent!
thanks very mutch , شكرا جزيلا
Hello, thanks for the video, I followed the cleaning instructions, but I still have a problem, when sending more than 2 sheets of some document, I get a ghost print of the watermark of the previous sheet, when I disassemble the transfer cartridge I notice that has remains of toner with the previous printing on it, apparently it is not discarding them, any solution?
greetings from Mexico
Are you sure the problem is the transfer belt? It could be caused by the drum too and by the fuser rollers
Hola Bernardo! has conseguido resolver el problema que mencionas? Me trajeron una impresora que hace exactamente lo que mencionas, un "fantasma" de la impresión, pero sólamente es en la siguiente página. y no existe un segundo fantasma...
@@victoraguilars.4281 hola, no pude resolverlo ya que no consegui otra unidad de transferencia para probar, lo que hace mi cliente es mandar a imprimir una hoja por una, y asi casi no sale el fantasma ya que el repuesto es costoso, va a esperar a que se le termine el toner para desechar el equipo.
Great Video!! Thanks a lot - I just exchanged the transfer belt!
My printer now is printing again :-)
However - the note on the little display "prepare for ne transfer belt" is still there.
How can I "delete" or stop this message ...
I don't know any reset method, it should delete itself with the new belt
you sir are a hero!
VERY helpful!!! Thanks!
Excellent!
How often do you need to clean the transfer belt? once every 10,000 pages or so?
Not necessary to clean it often. MAy be 30-40.000 pages if there are no print quality problems
i can't get the transfer unit to stick back up in its original position, which makes it impossible for me to put the waste cartridge back. you make it look so easy. any suggestions?
there are no tricks, it should go into position without too much problems
have a problem with my Samsung clp-365w. On power up it doesn't go through its usual warm up procedures. It is connected to the computer via usb. Removing the usb cable causes the conputer to sound so it knows it is disconnected from the computer. I think it is a hard wear problem with the printer itself. I have recently emptied the wast container. I worked after that but one morning after I powered up the printer all lights on the display came on steady and the printer didnt go through its usual warm up proceedures.
the waste toner container has a fuse, it needs to be reset
viandant5 how do you reset the fuse. I have tried cleaning the waste container
I do not know any reset method
hello, good afternoon, my printer marks the entire sheet with a very dark background, they told me that the problem could be the tape, if the tape is cleaned with alcohol and the blade, I will solve the problem or I have to buy the complete new tape, thanks .
Which tape? the belt? Yes you can try to clean it with isopropyl alcohol
Thanks for this video. i have managed to repair my printer
Merci !
THANK VERY MUCH
do you have a 'how to ... for the samsung C460W; backside is different so I could not take out the transfer belt
no, I haven't videos for this printer
I have C460W in front of me right now and it is exactly the same procedure :)
you take the transfer belt out from the front of the unit
Hi! I have a CLX-3305W and up to date 2 servicemen failed to fix it!
It printed well at the beginning, then more and more often the paper would jam but now when I start to print, it makes some noises (like something rolling inside), and then BEFORE it even takes a sheet of paper, it displays the same error message as before: "Paper Jam in Tray 1". What could be wrong?
Oh, and I must say that in the past it used to make this squeaky noise (like an old hinge) when rolling the paper, it made this noise more and more often and now it doesn't even roll the paper. What to do?
You can try to clean the pick up rollers with alcohol, or change paper (may be it's damp) but I think it's a mechanical defect.
Yes, I will try to do that. The paper is fresh from the box.
But everything looks (to me at least, I'm unprofessional of course) like some roller just seized up, because the machine squeaked more and more while rolling the paper and now it doesn't attempt to roll the paper. As I understand it, the pickup roller is only for picking up the paper and then some second roller starts working?? I think maybe this second roller got dirty and that's why it seized up? Do you have any video where I could see how to properly disassemble the printer and locate this "second" roller? :)
Thanks.
Here you'll find informations on how to clean a paper roller: th-cam.com/video/BDFugwT5o2Y/w-d-xo.html
Unfortunately the problem persists, evidently some internal mechanism for rolling the paper has just seized up. BEFORE it even takes a sheet of paper, it displays the error message: "Paper Jam in Tray 1" but there is no jam anywhere (I checked every location).
The printer is long past the warranty period so I want to disassemble it. The question is, which part is responsible for keeping the paper moving through the machine? This part is evidently broken or seized-up. Do you know?
sometime the cleaning is not enough, may be the rubber roller must be changed. there are gears in the side of the printer,may be one of them has a broken tooth
ขอบคุณครับ=thank you
Hello, I have refilled on CLP365 only black powder on all cartridge by local toner for black printing ,now printer is working but sounding very bad , how can remove it , please suggest me how to remove the sound .
the bad sound may be related to the gears, the internal meshing bar or the toner powder. It's difficult to remove a bad noise, try lubricate all gears. If the cartridge is working I suggest you let it work
viandant5 thanks for your reply.
hi, i have do this deep cleaning but after doing that my printer print only in grayscale. I dont understand why?
You have any idea?
What is a deep cleaning? Check the printer settings in the printer folder, may be it's set in "Grayscale"
excellent...thanks man!!!!
can i do this for samsung clp300 too?
No it's different
Salve Gianni, dopo aver seguito questa guida, ho rimesso tutto a posto ma la stampante adesso stampa solo ed esclusivamente in nero, i colori li salta, cosa potrei aver combinato? Strano perchè ho davvero fatto tutto abbastanza precisamente... Se hai qualche idea potresti rispondermi? Grazie
Stampa solo le parti in nero e i colori non li stampa? Non mi sembra un problema di cinghia di trasferimento, a meno che sia stata rimontata non correttamente e ora non sia parallela alle cartucce
@@viandant5 sebbene stampava male, comunque stampava sia nero che colori. Ho trovato questa guida, per la quale ti ringrazio, visto che lavoro come tecnico informatico ogni tanto metto mano anche a stampanti, prima volta che manovro una transfer belt, pulisco tutto sistemo tutto, rimetto su, provo e cosa succede? Stampa solo le parti in nero e salta completamente i colori! Da computer mi indica anche i livelli del toner presente ed è tutto nella norma… hai in mente cosa potrei aver danneggiato? Non è neppure mia, sono avvilito 😞
Purtroppo non mi è mai capitato, mi viene solo in mente che a lato della cinghia ci sono dei contatti, uno per ogni colore. Forse in qualche modo quei contatti sono difettosi o collegati male tranne il nero
@@viandant5 Per conoscenza sono tornato a riportarti che, ordinando una cinghia di trasferimento nuova, i colori sono tornati, quindi ho in qualche modo manomesso la cinghia precedente! (Però ho tirato un sospiro di sollievo, non ho danneggiato la stampante in sè)
By cleaning the transfer belt, do I still need to replace it? 'cuz my printer keeps showing a message that says "Prepare Transfer belt"
it also says "Prepare Fuser soon", what do I do? and where can I find these parts to purchase?
The cleaning do not cancel the error message. prepare fuser soon means that you have to change the fuser unit soon. to buy the fuser search with google
viandant5
Are the parts different from one country to another?
Suppliers in Saudi Arabia don’t provide these parts so I guess I’ll have to buy them from Amazon or eBay
Will I have compatibility issues?
it depends on which voltage do you have in your country, 220V or 110V.
viandant5
Thank you very much
You’ve been really HELPFUL =)
EDC program을 사용하여 Fuser, Transer belt, ITB, FCF, SCF의 message를 소프트웨어 초기화 reset해 주어야 합니다.
Hello, i have a clp 315 and i cant remove the drum unit, seems like its stuck?
Yes, it could happen i's hard to remove. Try to move it up using a lever or a screwdriver then pull it out
thanks, i fix it
Buongiorno, è dovuto alla cinghia una linea verticale sulla stampa? composta da un assieme di vari colori e non completa da cima a fondo. Come posso intervenire. grazie
E' più probabile che sia il tamburo. Comunque controlla se la riga è presente anche sulla superficie di tamburo o sulla cinghia. In questo caso potrebbe essere la lama di pulizia
@@viandant5 grazie mille, buongiorno
No sabia que allan x el mundo tambien repara impresoras!!!
How do I find out what error my printer has ? Because it is flashing red and not printing I don't know why
Can I use hydrogen peroxide to clean it as a substitute?
No, better the normal alcohol
What is the problem when the pick up roller won't engage? It won't turn.
II think it's not an electonic problem to the main board, you should have an error message. It could be a mechanical problem, a gear or something not in the right position
das hat mir geholfen !
Very well thank you.