01-04 Jeep Grand Cherokee Hydraulic Fan Solenoid Mod, Remove & Replace
ฝัง
- เผยแพร่เมื่อ 9 ก.ย. 2024
- Also, show how to make a modification to the solenoid to increase the fan RPM by 100%. In 2001 Jeep Grand Cherokee with 4.7L was equipped with a hydraulic cooling fan for the radiator. I Explain how the Engine, Transmission, Battery and A/C system pressure communicate with the ECM/PCM to control fan RPM using a Pulse Width Modulated signal to the solenoid. The normal operating RPM at idle is 100 to 500. This is due to a controlled minimum oil flow requirement through the fan hydraulic motor.
To test the solenoid unplug the temperature sensor located between the A/C compressor and the alternator just in front of the intake manifold. If the solenoid is working properly the fan will go into Hi-speed. If there is no change in RPM of fan the solenoid or the wiring from ECM to solenoid is at fault.
Using Laser Digital Tachometer to show the RPM of the fan and how it increases as the temperature rises and as the pressure rises on the A/C system.
Donate to Help Support Channel www.paypal.com...
AGPtek® Professional Digital Laser Photo Tachometer Non-Contact RPM Tach amzn.to/2XqbsHx
8-Piece Torx Bit Socket Set 1/4" Drive amzn.to/2Ups2Fo
Red Line 30404 Power Steering Fluid - 1 Quart Bottle amzn.to/2U8VtAe
Radiator Jeep Grand Cherokee 4.7L 52079883AD amzn.to/2DtT1tZ
Valvoline Zerex G-05 Antifreeze/Coolant amzn.to/2ZjqUqA
Some of these links go to websites and some are affiliate links (including Amazon) where I'll earn a small commission if you make a purchase at no additional cost to you. This helps me to continue to make videos like this. Thank you for your support!
Facebook: / martinbuilt-2351766611...
#jeepgrandcherokee #jeepgrandcherokeemods
Man that seems like an unnecessarily complicated design from Chrysler.Well explained by Martin as always.
Yeah I'm so glad to get rid of that hydraulic fan and go full electric.
Sr. Usted me ha ayudado mucho a mejorar y reparar mi WJ 2005 4.7 Lt. Eres el único en esta red de TH-cam con esa gran calidad y profecionalismo. Felicitaciones y gracias
I just did this to my original owner 2004 Grand Cherokee with the 4.7. First try I turned the screw in 3/4 of a turn, tested it and it was a bit too fast. I backed the screw to about 1/2 or so in from factory setting and I got the increased fan speed/air flow I wanted. More radiator air flow for free and appreciate it here in central Florida during summertime.
I'm glad you liked it and found it helpful. Thank you for watching.
I did this to my 04 with a solenoid I got from the pic a part, got 3 of them actually. Putting hood vents in made a huge difference, put the A/C on and the amount of hot air coming out of the vents is amazing. A huge trans cooler also reduces the load on the radiator.
Hey Martin, thanks for the great vids! During my research on the hydro fan setup for my 2001, I just came across this FORD part that is suppose to be a replacement for the unavailable jeep solenoid;
Ford XW4Z-3783-CA - ACTUATOR ASY
and the wiring plug for it;
Parts Master 84080 2-Wire Multi-Purpose Pigtail Connector for Ford Products
Hello, thanks for the info. did you find and install this part?
@@jesusrperezd I found used and tested Jeep part on ebay
so, the ford actuator fits into the jeep hydraulic fan and doesn’t leak? and you just had to splice/integrate the jeep wires to the ford pigtail connector?
Your videos have gotten really really good over the years man! Love the work you put into these videos Martin keep it up
Thank you!
@@martinbuilt where u get that hydraulic fan solenoid new
Never mind, I just watched your video on installing an electric fan! I'm going to do this, but probably use a crown vic e fan set up.
Thanks again
Yes the crown Vic and Lincoln Mark 8 and even the Mercury villager fans work well.
Martin's videos are always really helpful. I just did head gaskets and figured I'd try this mod since the fan was out. I have an 04 Overland, and mine has an entirely different solenoid, which does not have the ability to be adjusted. Mine is the 3 pin connector. I compared it to an 02 fan I had , the 02 has a 2 pin connector and a separate ground wire. So, if your solenoid does not have the torx bolt it likely is not adjustable.
Thank you Eric, Yeah unfortunately the the 3 pin solenoid is not adjustable.
Even after I made this modification, it did help I was not entirely satisfied due to the Las Vegas heat and remove the hydraulic coling fan and replaced it with an electric with this video.
th-cam.com/video/J02nYci5DS0/w-d-xo.html
how do you remove the solenoid type that doesn’t have the torx bolt? that’s what i have
I really like the hydraulic fan setup. It's intelligent and only ramps up on demand. It doesn't wear out your water pump bearings with like a normal mechanical fan. With that being said, I always felt the fan comes on late to start cooling heavily. I'll see coolant temp up to 210 and oil up past 215 before it'll kick up. Now the other factor is the transmission. Worth noting since I've added an auxiliary cooler my transmission temperatures have been lower. Noticed the fan won't ramp up until the pan temperatures get to about 165-170 which doesn't happen to often. I think I'll find a spare solenoid from a yard, give it a turn and replace mine.
I also replaced my radiator. There was areas that had a lot of dirt packed into the fins that I couldn't see until I got the radiator out. That helped cool it down some. The dirt came from the former owner. I know he used it to play in the dirt and mud.
@@martinbuilt I probably need to replace my radiator again here too. It was done at about 100k miles and I've got about 210k now and I saw a drop of coolant on the bottom between the plastic and and aluminum. Wish they made an affordable all aluminum radiator. The eBay ones "fit" the 01-04 with modifications since there for the 99-00 and they were about 2" taller if I remember correctly. What would be best is if there was a way to reprogram ECU to turn on the fan quicker with coolant temperature rising about 200*
Hey thanks. Love your videos since I wrecked my 98 XJ crawler and decided to go with the WJ for an overland build. I'll keep watching for when you show the mod.
that was an informative video. the funny thing is i have a 2006 jeep commander and have the very same cooling fan setup. i think jeep should have gone another way when it comes to this setup. you can't even swap out the fan for an electric fan that in my opinion would have worked better.
Very good video, this cooling fan system is also on the gen 3 vipers. I have a supercharged viper that I needed more air flow over the raidator. This was an amazing mod! Thank you
Glad you liked it, I didn't they used the Hydraulic fan on Vipers 🤔
Yep, just about the same years as the WJ's
I just replaced the steering pump pressure line about 2 weeks ago. Had I known this was the reason my fan stopped working(hydraulic fan motor not electric) I would have made the change myself. But now its $174 part and .5 hr labor at the shop($183.HR labor).
That was really informative. I always wondered why the 4.7 had a extensive cooling setup. I wonder if increasing the RPM of the fan above what it normally runs at would cause more wear than what was expected from the factory. At least you can still buy it from them for now.
AN EXCELLENT EXPLANATION ON THE FAN BETTER THAN ANY OTHER ON YOU TUBE!! If possible, can you discuss how you know whether the problem is the fan or the power steering pump if you are experiencing hard or no power steering
Good mod. I'll do it this weekend. Never heard of this mod before. THANKS again, Martin!!
Heading to the yard this weekend to pick up an extra air box to do your ram air mod.
Let me now how it turns out.
Been a fan of Martin for some time. Tried the mod as described in the video with limited success. What I discovered is there is a fine line when turning that adjustment screw. Too little and not much of an increase, too much and it goes into airplane mode. After making some very small adjustments, it now spins a fair bit faster at idle and works really well when the temps climb.
I've been watching a lot of videos you like one of the best mechanics I've seen
Thank you, Michael
You do good thinks good job man...All the best
I have same jeep like yours and i learn many thinks from you .
martin thank you your vid is perfect for educating people about a cooling system that many dont know even exist or are unfamiliar with
you are very welcome, thank you for watching.
Like Your channel very much. I'm from Armenia. Will be glad to see the front and rear axle alignment! Thank U.
The replacement 3 wire solenoid for my 03 Laredo does not have the adjustment screw. So it looks like I will have to go with the electric and clutch fan setup to get more airflow at low speeds. It was worth a shot, thanks for the good videos martin!
You could also go all-electric as I did. Here is a link th-cam.com/video/J02nYci5DS0/w-d-xo.html This has been working great.
does the solenoid style without the adjustment screw mount differently? i dont know how to get mine off and mine has no torx bolt
Thanks alot. My jeep will work tomorrow
I've been wondering how I could get it to run faster. Tried messing with the 3 pin connector with no luck. Thanks man👍
You can throw a permanent magnet on the back of it to have the fan constantly moving. Which is what I did to one of my JGC's. (I'm on my 7th).
Where would you put the magnet?
@@timbenracing right behind the coil of wire. It will pull the rod to allow the fluid to flow and kick on the fan.
@@JF32304 awesome thanks for the quick response. You mean right on the screw head right? Where it holds the solenoid in?
@@timbenracing no problem man! Yeah put it right on the screw head... I used a rare Earth magnet... Really got that fan going!
@@JF32304 how big of magnet did you use Jesse ,did you just stick it where the torch head is ,did you disconnect the solenoid to make the magnet work ,RSVP,? Thanks Jesse .
Hey that was good info. I haven't messed with my cooling system much but I need to try this. With my demands I could use the added cooling (airflow)
Glad it was helpful!
Nice sleuthing there Martin! Seems these fan units are up to around $1400 retail from the dealers now. If you don't have a leaking front seal or broken blades, and just have a heating issue because the fan is slowing down, this is a really good alternative to running out to the dealer and *Just Empty Every Pocket* . 😁👍👍
Wow... There's no way I'd ever give $1,400 for that hydraulic fan. I'd either go to pick a part and get one for $30 and take a chance with that or do what I just did and convert mine to Electric. I should have that video coming out in the next week or two.
My favorite is Justify Every Expensive Purchase
Congratulations u r a master
Thanks for this video.
Great video, thanks. My wife had our recently acquired high mileage 2004 4.7 WJ overheat in stop & go traffic. It took me a while, even parked next to our suspension modded 1999 4.7 WJ, to figure out the 04 has a hydraulic fan motor (shades of my 1967 Thunderbird windhield wipers!), while the 99 has both engine fan and an electric fan. I've added a couple quarts of water, and will watch this 04 closely. Seems to an old guy like me that a good engine fan, with proper shroud, would be more reliable, perhaps a quality flex fan from the speed shop.
In theory the hydraulic fan should work great unfortunately the ECM is trying to get the engine to 204 degrees even if you put a 180 thermostat in it is only going to delay reaching plus 200 degrees. Even after doing the mod to the solenoid which did help I was still seeing temperatures above 200. I recently did a electric fan conversion and couldn't be happier with the results.
Make sure that you bleed the air out of the cooling system by removing that bleed screw (8mm Allen) and let it run for 10 to 20 minutes, do this with a cold engine.
Thanks. I have been thinking seriously of going with an electric fan. They are common, both on vehicles and in the aftermarket, so selection is good. Side note: I wonder if Daimler/Chrysler/Jeep engineered the power steering pump for more output on the hydraulic fan models. Might have a better chance with a hydraulic MileMarker winch (which my friends at Skagit Hydraulics told me is very weak without an auxiliary pump).
@@lanedexter6303 I use the hydraulic fan steering pump on my 98 XJ as I have it ported for hydro assist it definitely moves more fluid then a standard power steering pump
Hi Martin I'm Jan from South Africa Johannesburg
شكراً سيد مارتن استفدت كثيراً
Excellent Martin Thank you so much
You are very welcome
Martin ,thank you for your video, tell me where is the freon pressure sensor in the system, which gives a signal to increase the fan speed? I did not increase the fan speed when you turn on the air conditioner, when the refrigerant escapes through a safety valve, but the solenoid is working, if you throw the connector from the temperature sensor of the engine, the speed increases. Thanks.
Martin i love what you do.
Hello Martin I have a 02 jeep grand cherokee limited and my interior lights stays on but very dim they do not turn even when I'm driving or the jeep is off what might be the issue? thank you
Had to replace this solenoid...found one in a junkyard and learned it was different than the one in my jeep. Ended up going back and getting the entire fan assembly...what a pain. All fixed now but headed back to Iowa from Tennessee, picked up a new camper. Thinking I could use more cooling and this might do the trick. She tows well, but power is a little low on my non-HO 4.7. Anyway, you mentioned mpg when cranked all the way down, how's it do only half way? And why do you think mpg's were affected? More work for the power steering pump I would guess...??
Yeah getting those fan assembly out is no easy task. The best way is to pull the fan and the radiator out as one. I haven't noticed any decrease in miles per gallon turning it half a turn in. The loss of miles per gallon when I turned it the full turn was due to the extra load it was putting on the power steering pump.
PS I'm originally from Iowa been in Vegas since 93.
Awesome information, thank you!
Glad it was helpful!
You're videos are well done. Great job!
A question, CA you replace this system with a new aluminum radiator with electric fans? Seems much simpler
Thanks
Thanks very much ... very informative
Glad it was helpful!
You are the man, Have you considered looking into a 04 Dakota electric fan set-up and seeing if that would work? How does one go about getting one of your martin built mugs?
Thank you Chris, I am currently working on a electric fan conversion. I'll take a look at the 04 Dakotas and check out their fan. I'll have to look into the mugs I was just asking a friend of mine about that. I got to figure out how to do a large order to keep the prices down.
Hi, excelent video I like it so much. Hey I have a problem with a 07 grand cherokee, I have my steering wheel so hard, and I was wondering if this solenoid could be the reason, the power steering fluid level is ok.
Holy Cow... Am I glad mine is a 01' XJ ..
Love your video...I have a Jeep 2006 Commander with the 5.7 Hemi....Had AC serviced and my mechanic said my ac fan was not spinning fast enough. He recommended to replace it for 2500 bucks....OUCH!! I said nope. I was hoping that this is the issue with mine as well. Can you let me know what part number to look for? And is it easy to replace it while the fan is in place? Thanks Randall
hi ...
I've done the mod yesterday and i have turned it 1/3 of a turn ..
unfortunately no improvement and the fan didn't speed up ( maybe a very tiny bit 😅) ...
I'm planning on turn it to the rest of full turn and see if it would make a difference ...
also I've done some testing and found out that if the voltage decreases on the wire that comes from the ecm the fan will speed up and if I ground it like connecting it to the nigative battery the fan will go full speed ...
so maybe i will build a circuit that regulates the voltage on that wire
what do you think about this? it could be a nice project helping all those people with hydra fan
Wow sounded like a NASA wind tunnel
Yes, ready for take off
Just watched this again. What was the original fan speed vs modified. And what about 1/4 turn thnx a bunch.
thanks for the video.. I had a problem with the 2008 jeep commander 3.0 crd the fan's rpm is slow.. where can i buy the solenoid that you install?
The only place to get them is eBay or salvage yards. Used is the only option.
Wonderful video and subscribed
Thank you!
Lincoln ls and Ford got same system, it dose go out and it is positioned in the one of the hardest place . They don't make them no more , that means good luck finding used one or overheat your car in traffic... new use to cost 200 $ (like I'm saying , they don t make it no more but it dose brake). I see it as a bad design and waste of money considering they don t make it no more and it cost a lot.
Thank you brother. Greath job, ✌
Thanks! I just did this to my wj, I might go back and turn it out maybe 1/4 because 1/2 seems like to much. She roars now and stays super cool! My ac still dosent work tho ☹️
Your lucky my ac works great but it overheats like a bitch! Im pissed.off the fan runs full speed.when I unplugged the coolant temp sensor then all of a sudden slows when I plug it back in I'm trying to find the issue
@@isauroalfredobanuelos6342 What I learned was these factory radiators with plastic sides and single deck aluminum, fins can get clogged in places you can't see, and loose cooling efficiency. Also, I found when replacing my radiator, that there is some side wings, that block air from flowing around the radiator sides forcing the flow thru the radiator, looks like cheap flexible rubber. This stuff gets tossed and air just flows around the radiator instead of through it at lower speeds. Its shown as "required" in the factory manual on the 4.7L. Ha, ha, on mine I left it out, just like the previous owner, did not know, and I was under pressure to get back on the road. An ALL ALUMINUM radiator would be best. Also, I found the HPS Performance silicon radiator hoses don't get the stupid endless little leaks at the hose clamps like the factory EPDM radiator hoses. I like the hydro fan setup, but don't let the steering fluid leak or get real dirty, as your cooling depends on this fan moving the correct amount of air.
Hi , love your channel.
I have a question for my 2010 GC 5.7 with the hydraulic fan set up . Is it possible to have a bad coolant temp sensor even tho the cluster gauge is working and showing the coolant temp reading increase?
Thank you very informative
Glad it was helpful!
Hello, my vehicle has a 2.7 fan, it goes into fast mode at approximately 105 degrees, the vehicle cannot be disassembled until those components, what could be the reason for this?
I have a 2008 Jeep Grand Cherokee 3.0 CRD does anyone know how to get this solenoid off? It looks the same but now spot for a torx and in between the solenoid and the body looks like a nut but it’s very skinny like you need a special skinny wrench 🔧. Seems like a dealer tool for when the do remans and then replace that solenoid. Anyone do this or have ideas how I go about it ?
I have the same one .. any ideas ??
Great vid, thanks for all the info! Hey what oilfilter are you running?
Thank you. I appreciate that.
I am using a Baldwin B2 oul filter.
Hi, I am looking for a solution to increase the fan speed of a jeep grand cherokee WK 3.0 crd, is it possible to do the same for this engine? Is it possible to speed up the fan in WK 3.0 crd?
Good day Mr Martin I watch your TH-cam’s videos all the time Mann your a genius I’m writing you to ask if you have an extra hydraulic cooling fan solenoid for 2004 Jeep Grand Cherokee 4.7 also a driver door wire harness that leads from the truck to the door it has a short that you might want to sale they went out I wire the solenoid straight to the fuse box so when I needed it I hit the switch but now that joker is gone truck over heats looked in half the junk yards on my side of town on luck can you help thanks
Count me in for at least two mugs!
Dear Martin, Do you recommend converting the hydraulic fan to electric for 2004 - 4.7L Jeep Grand Cherokee?
HOLY CROW Martin, I never knew this existed, WHAT A CONTRAPTION THEYV'E BUILT. I have 2 ZJ'S with the clutch fan & want to convert to electric this year still doing research but HELL COMPARED TO YOUR SET UP MINE SHOULD BE CAKE. How did you figure out about the adjustment on that solenoid ? THANKS FOR YOUR WISDOM & YOUR TIME, Henry.
I will also be taking out this hydraulic fan currently mocking up the electric fan.. After seeing some pictures of the solenoid on the internet I had a feeling if you turn that screw one way or the other it was going to affect the RPM of the fan.
Smart move, I just saw your vid. on the electric fan you're going to put in & REMOVE ALL THAT CRAP.
@@NoWr2Run yep just purchased a few more items to complete the electric fan conversion.
Great videos! Question...did this MOD make your power steering easier or lighter? Even after replacing my steering gear, hydraulic fan and power steering pump "AND" using the right fluid, our steering is still harder than we'd like especially at lower speeds.
It made no difference
Gracias mil gracias
Mine has electric and clutch fan both were fail I got electric one going it holding but clutch fan is tough with out air hammer wrench my brother has shop 04 4.0 I seen some one put dodge 03 fan in had same thread but had to cut shroud
Could this be the reason my 04 jeep is over heating ???
thanks man.
Martin! Need some help! What size and type of "O" ring is used on the inlet 1/2" high pressure line that runs from the steering pump and connects to the bottom of the hydro fan? Also, can you confirm the torque setting for this bottom connection, my service manual has an unbelievable 36ft pounds !!! Can that be true? I have an annoying power steering leak at that bottom fitting, rubber "o" ring does not seem to work and I won't tighten to 36ft # on what looks like an aluminum housing!
Nice tutorial. I now know why my ac won't work correctly since it won't ramp up. I bought a used solenoid and attempted to replace it. When I unscrewed the solenoid, the end came off and the main part of the solenoid remained in the fan motor. Has anyone had this problem? I didn't try to use pliers to try to unscrew it since I have a 45min drive home.
Thank you. Yeah that problem with the solenoid unscrewing just half of it has happened to several people and I've had it happen to me one time out at pic a part when trying to removing one. I was able to clamp a vice grip on the very outer edge and break it loose. You may want to try that.
@@martinbuilt thanks for the quick reply. If it doesn't break loose would the vise grip marks prevent it from working if I had to reassemble?
do you know how to force high rpm of this Hydraulic Fan without drb III ?
I have a problem with bleeding. My car does not overheat, but the new pump howls all the time
big problem now is that you cant buy the correct fluid from Mopar anymore. The owner before me had power steering flushed and it looks like just regular pink stuff.
This one here me be a good substitute for the discontinued fluid.
amzn.to/4aQG1eA
Hello everyone. So, I have a question. Does the fan on the G. Cherokee 2001 WJ benzene 4.7 V8 should be spinning when the motor is just running? My fan kicks in when the temperature gage goes over the middle mark. Cooling the motor down a little and switches off... Now its 3 degrees Celsius here now and for some reason my motor is getting hot constantly (then the fan kicks on, cools it to below half mark and so on...)
Coolant in the radiator, full and I did the air bobbles bleeding. There is power steering fluid, full. Can someone pls explain or point me in the right direction... THNX! great vids.
My 06 Jeep Commander 5.7L gives occasional vibrations which can be felt on the whole car. It only happens when the temp guage reaches the middle. Do you think its due to the fan being off balance? No codes except for a knock sensor circuit DTC.
GREAT VIDEO! Please, is it possible to be adjusted on 5.7 HEMI as well? Many thanks!
Thank you, I appreciate that I'm glad you liked it. I am not familiar with the 5.7 solenoid.
There are some that are not adjustable on the 47 as well.
I wonder why the mileage decreased? Perhaps increased load on PS pump?
Yes exactly what I think happened as well.
The power steering pump had to work harder to spin the fan that fast.
Hey Martin great video! how did the half turn mod work out in the long run? Did it provide adequate cooling or Was the Jeep still heating up in traffic and stop and go? I’m thinking about doing this mod as well.
It did help quite a bit I had temps around 10 to15 degrees cooler but not enough for me. I'm wanting the most and the best performance I can get out of this 4.7 ended up switching to an electric fan. Here is the video on that conversion th-cam.com/video/J02nYci5DS0/w-d-xo.html
hey Martin thanks for the reply. I did see your you E fan conversion video, it was awesome but too much for me since I’m sort of a novice! I did the solenoid mod today and after install everything seems great. Had a question though. I don’t know if you remember or not but when you did the mod and started the car for the first time did the fan kick up really fast at about a medium rpm(somewhere between idle speed and full blown airplane mode) and then slow down to a lower rpm when the car came up to operating temperature? Sorry for the super long message.
@@xmanzcovers4434 No, mine seemed to operate normally, just at higher RPM then before and never close to airplane mode.
Hello Martin I have a wj 2001 4.0 and I already bought the fan relay and got the radiator fan working , wanna put the fan clutch and fan to get some more cooling what do you recommend? Thanks.
another great vid Martin. my steering is very hard to the left at stand still. have just fitted a new pump but still hard to the left at stand still. any ideas? cheers. keep up the good work.
That's weird, I'm kind of wondering if there's something wrong with the steering gear box. You may want to remove the tie rod end at the pitman arm and then turn your wheel left to the right and see if it's still hard and if so it would be the steering gear box
@@martinbuilt thanks Martin. ill give that a go at the weekend. I never thought of that.
i cant find anything on your channel for clutch replacement if you dont have a vid can you suggrest a vid for this: 3.7 dodge dakota sxt
I have been trying to research this. My wife’s GC is a 2006 with the 5.7 and currently runs this hydraulic fan set up. I have never had any trouble with it yet. I do need a new radiator for it. The plastic is leaking now after so many years of use. I am assuming the radiators for the GC are the same wether it be gas, diesel? But I am not finding a listing for a radiator for the GC with the 5.7. It only shows the 3.7, 4.7, and 6.1. Is there a difference in the mounting flanges or anything? Or do they all use the same radiator?
So I have read you can ditch the Hydraulic fan setup for a mechanical fan since the water pump already has a threaded stud on it. But when you do that and unplug the pressure switch with the fan it causes a check engine light. Does anyone know how to bypass that so the light does not go on.
You're spoiling my upcoming video . LOL . Yeah I read that too. Actually it's quite easy to fix. You have one or two choices remove the solenoid from your hydraulic fan and plug it back in or get yourself a wire wound 10 Ohm resistor I would suggest using a 100 Watt resistor and wire that to the two wires that went to the solenoid. It would be best to put it in the Stream of air where it can be cooled as a resistor will get warm.
The hydro fan is capable of moving MUCH more air then an electric. Put it in "airplane" mode by disconnecting the coolant temp sensor and start it up, you won't find an efan that moves that much air.
I have a problem want to share with you. My car has a hydraulic cooling water system. The wings aren’t working properly, they are sometimes turn on and sometimes not. When it needs a high U-turn, it doesn’t turn on. But for the low U-turn (in the city) it/wings are working just normal and fine. I‘ve changed the water temperature measuring system, but it doesn’t help.
Can you help me and suggest me what can be the problem? Can this problem caused of solenoid?
Thanks a lot in advance and waiting for your answer :)
BR,
Levan
Unfortunately something must have been lost in translation. A lot of what I'm reading doesn't make sense. But I believe what you're saying is that you're hydraulic fan is not working properly. Try unplugging the temperature sensor the hydraulic fan should go into high. If it does your solenoid is working properly.
Thanks for your quick reply. I‘m sure now, that the solenoid doesn’t work properly.
Thanks a million:)
BR,
@@martinbuilt Hello Martín, I have a problem with the fan and it is that it does not cool me well because it rotates slowly
why is that? Should I change the solenoid or temperature sensor?
Please... i need your help, master
I changed the solenoid out, the code came back on. Any ideas on what else might be the issue.
Cooling fan pump assembly in Australia $2,500 AUD , but is no longer avaliable
best to get one from a salvage yard, in the US $25.00, over $1,000 new
Hi Martín
My hydraulic fan does not seem to cool the motor well ... apparently it does not have enough RPM. Why is that happening, Martin?
Will it be due to the solenoid? Is there a fix or should I change the whole system? :(
I wait your answer
Hi I have an 01 Jeep Grand Cherokee with the 6 cylinder I haven't overheating problem and I think I have a weep hole too but I'm not familiar I didn't know what was my vehicle have this
If you're losing fluid from the weephole on the water pump I would replace the water pump ASAP.
how do you test the solenoid to determine if it's still good and working (besides installing the fan back in the engine bay)?
Using a ohm meter test across the two connections you should see approximately 10 ohms. This is with the wiring disconnected of course
Do u now what type of oil take those power steerings
Great video 👍🏾 and thanks for the sharing.
Thank you.
Martin,
My engine does not get really hot since I did a full service (new radiator, cap, thermostat, water pump, coolant, hoses, and sensor), however my fan still doesn't spin fast. I know that the ECU sends a signal and the hydraulic fan should kick into overdrive mode if it gets above a certain temperature, however like you stated I would like it to do that before it gets to that point (which usually occurs after highway driving for a while then getting gas). I am going to try disconnecting the sensor to see if the fan picks up speed. If it does, where do you think I should start troubleshooting?
Also, a random side note, have you ever tried Marine Two-Stroke oil TC-W3 in your gasoline? I think you would be interested in reading up and possibly trying it. Here is a forum regarding the matter, long story short you put 1 oz of this TC-W3 into your gas tank for every 5 gallons of fuel:
www.ls1.com/forums/f48/been-testing-oil-91206/
I've been doing it on my WJ for over a year now and can't say if it hurts or help, but when I did my hydraulic valve adjusters the top end was clean, no sludge or issues with carbon buildup.
Update:
Disconnect the harness to the coolant sensor, started the Jeep up and the fan was spinning the fastest I have ever seen it. CEL came on for P0118 (Coolant Temp sensor high input) over-ride the ECU and kicked the fan into hyper-mode. When I shut off the engine, reconnect the harness, the fan barely spun as it usually does.
I know that if I am in a pinch I could disconnect that harness, but I would rather find a way to get it to kick on sooner and not have it running full speed the whole time the sensor was disconnected.
Do you know if there is any way to have this occur? Is there a way to install a manual over-ride where I could put full voltage to the system if I feel the engine is getting too hot?
I know you did the e-fan conversion, not trying to do that if there is a solution with current set-up.
Thanks Martin
I Martin. Could you indicate me which oil (ref, name) is recommended for the fan/steering hydraulic system? Thank you again.
MS5931 should be the only fluid be used in the JGC with an hydraulic cooling fan.
Hey Martin! I had the hydraulic fan solenoid 1499 Check engine light code so I replaced my fan with a junkyard hydro fan and it's solenoid looked like it was in great condition. I got everything back together and cleared the Code with my blue tooth device but it popped right back on.. do you know how to get rid of this code? My only other thoughts were to disconnect the battery for a while then try resetting the code or have it professionally reset. I'd hate to think I'd have to replace another solenoid. Maybe I actually have a short in the solenoid wiring??? ☹️ Your thoughts?
check the solenoid with an ohm meter it should read around 10 ohms, that is with the wiring unplugged and only reading the solenoid itself.
@@martinbuilt will do! i think i found the problem... did you know the 02 sensors share a fuse with the hydro fan??? 🤯
@@ProjectDanH really? which fuse is it?
Hi Martin, I've got the 3 wire solenoid on my 04 & from what I've been reading it seems im out of luck on this mod. I have 2 questions about it though: do you know how to get the 3 wire solenoid out & if so could i just put a modded 2 wire solenoid in its place? Or if this won't work could i put a variable resistance switch in line with the coolant temp sensor signal wire to vary the voltage the ecu sees to up the fan rpm?
I don't think there's any easy way to convert to the single wire solenoid.
Having an issue with my hydraulic fan solenoid now. Error P1499. Anyone know where I can find a replacement solenoid?
Would you know why y 04 Grand Cherokee does not have the ground wire that mounts to the fan housing? I noticed that it looks like your solenoid only has 2 wires in the connector?? My solenoid has 3 wires in the connector.
Do you know why? Do I have an upgraded model??
Any help would be greatly appreciated.
Thank you!
I believe they're just grounding through the metal of the solenoid, eliminating the wire.
Hello from Spain. I have the same hidraulic fun on my 2002 European Jeep GC 2.7 Crd (Diesel).I do not have temperature problems. When i turn on the car, and it is cool, i have a rare noise from the fun,that disapeer when Hot.What could It be?(.i think in Jeep service do not sell me a good hidraulic fluid). A lot of thanks.GOod Job
The hydraulic fan requires a special fluid, This is one of the approved fluids
Red Line 30404 Power Steering Fluid - 1 Quart Bottle amzn.to/2U8VtAe
Here's a question you might be able to answer.
I had to change a radiator so I disconnected the fan and I know that that it had the hydraulic cooling lines the vehicle is a 2006 Jeep Commander.
On the two lines the one that would be on the driver side was obviously a flare fitting but I noted I could actually just pull the fitting off of the line screw it back up into the (cooler). And then the line actually just pushed up into the bottom of it and clicked in?
Any other type of flare fitting I ever had the fitting would slide up the line over the flare and into it's connection.
Do you know why I would have a line that would just pull out of the bottom?
There was another plastic type of seal piece that would slide up the line and click into the bottom of fitting in between the flare and the connector. But I would think if there is a significant amount of pressure on that left driver side line that it could just popped that line back out????
I personally haven't seen the hydraulic fan in the commander. Sounds like they changed the type of connector since 04. Is there any type of safety lock for that type of connector perhaps it was missing? I would be a little concerned as well if it was something you were able to just pull off by hand.
I have an 04 grand Cherokee I searched on TH-cam and found out you can change those solenoids so I bought one used but in the mean time I had mines direct power as soon as you start it turns on at full power making a loud noice keeps my engine cool but it’s to loud to keep driving with the family. I installed the new and disconnected the power but the fan still does not kick in fan barely spins I can stop it with my bare hands if I tried
There may be something wrong with your fan motor. You could try modifying the solenoid as I've shown in the video and see what that does for you.
Good morning thank you very much for this information. Please help me. I have separated the temperature sensor between the air conditioner compressor and the generator. In fact, the solenoid works correctly. The fan entered at a very high speed. What after we have to do because when you turn on the air conditioner or cross a rough sand road that increases temperature and the fan does not increase its speed? Thank you
Have you tried the solenoid mod? If so and your still not satisfied it may be time to convert to a single electric fan. Like I did in this video th-cam.com/video/J02nYci5DS0/w-d-xo.html
@@martinbuilt Thank you for your interest. I am from North Africa (Libya). I do not have the electrical equipment required. I want to repair the hydraulic fan. I want to fix the fault. I have followed the steps I mentioned. I have separated the temperature sensor. The fan is working very high. So what to do after and sorry for the many questions and thank you very much
@@naserasas8428 so this tells me that you're ECM, the cell annoyed in the fan all work properly but did you do a modification mentioned in this video that will increase the RPM of the fan by nearly 100% And help the engine to run cooler.
@@martinbuilt Thank you for your interest. You have modified as in the video but remain the same as the previous power. Do we increase the modification by rolling another cycle in the same direction
@@naserasas8428 I would not recommend it the fan will go into high mode all time and you will see your mileage per gallon go down. If your engine is still running hot I would recommend doing a electric fan conversion there's nothing more you can do with that hydraulic fan to make it any better..
Thx Dude
You are welcome👍
MARTIN
MY NAME IS BILL I NEED SOME HELP I REPLACED MY RADIATOR IN MY 2003 JEEP GRAND AND NOW I DONT HAVE ANY POWER STEERING AT IDLE I HAVE POWER STEERING AT 1500 TO 2000 RPMS I HAVE FLUSHED THE SYSTEM AND REPLACED THE POWER STEERING PUMP DOES THAT SOLENOID HAVE ANYTHING TO DO WITH FLUID PRESSURE GOING TO THE POWER STEERING GEAR BOX WHEN I FLUSHED THE SYSTEM I HAD A TON OF FLUID COME OUT OF THE RETURN LINE FROM THE FAN BUT VERY LITTLE COMING FROM THE STEERING COOLER BACK TO THE PUMP CAN YOU HELP ??