bohot achi or asan video hay main dostoon ko aik or baat batan chahta hoon yahan amoman aik confusion hoti hay k MPU or flywheel main gap set kesa kya jay kiyon k MPU instal karny k baad aap gap messsure nahi kar sakty or na hi aap gap dekh sakty hain tu main yahan aap ko aik asan tareka baton ga jis se aap MPU or flywheel main gap asani se set kar sakty hain. MPU ko instal karty hoy is ki thred ko kasty jain yahan tak k MPU flywheel k sath tuch kar jay ab MPU ki thred ko 1/3 thred wapis khol lain or cheknut kar dain .MPU bilkul sahi gap main aa jay ga or bilkul theek kam kary ga.
Ok I'm using a magnetic pick up for Gas engine it's resistance is showing below 1000ohms. Can I test it by keeping it in front of a rotating drill machine with gear teeth
Thank you sir lekin mpu ko fit karte samay hame kaise malum hoga ki mpu apne Range me fit ho gaya hai ? Agar mpu kharab Ho jaye to kya engine start hoga?
asad bai agr magnet field ko teeth cut kr rhay hain...to coil me kaisay voltage paida hongay...coil ke hisaab se to field saakin position me hoga...agr teeth magnetic to coil tb field ko cut kray ga...field b mpu aur coil b mpu me....how is it possible? ke voltage paida hu...
Dear jo magnetic field around coil mojood he usko jab flywheel teeths cut karte hen to us me fluctuation ati he uski wja se coil me emf generate hoti he.
@@muhammedkhan9311 34 Series (peec) me 2 mpu hotay hen. aik 150 ohms aur dosra 1000 ohms. 1000 ohms wala ECM (peec) ko signal deta he aur 150 wala panel ko. 35 series me 150 wala hota he
Bhai .. ap ne fly wheel k teeth ka cut karny wali bat sahi nahi btayi ha. Or ap ne faraday's law b theek se nahi samjha. When a conductor cut the magnetic field ..then e.m.f is produced in that conductor. (Ap keh rahy hain ..permanent magnet or coil dono same MPU k andsr hoti hain .lekin actually .. fly wheel k teeth me se kuch permanently magnetized hoty hain . Jo k MPU k andar wali coil ko cut krti ha ..or coil k andar e.m.f produce hota ha. Thanks
Really you are very talented Engineer and youtube as well.
Love from India 🇮🇳
bohot achi or asan video hay main dostoon ko aik or baat batan chahta hoon yahan amoman aik confusion hoti hay k MPU or flywheel main gap set kesa kya jay kiyon k MPU instal karny k baad aap gap messsure nahi kar sakty or na hi aap gap dekh sakty hain tu main yahan aap ko aik asan tareka baton ga jis se aap MPU or flywheel main gap asani se set kar sakty hain.
MPU ko instal karty hoy is ki thred ko kasty jain yahan tak k MPU flywheel k sath tuch kar jay ab MPU ki thred ko 1/3 thred wapis khol lain or cheknut kar dain .MPU bilkul sahi gap main aa jay ga or bilkul theek kam kary ga.
Asad bhai you are great man dil se dua nikalti h....
Assalamoalekom bhai I am from India thank u so much bro❤️
Mashallah bhai allah aapko salamat rakhe
Love from Bangladesh 💝💝💝💝
Sir please do video on fuel system(Gas)
Assalamualaikum Asad bhai me from Bangladesh. Good description.
Walykum Assalam. Thanks
Much Appreciated brother
Well explained. hats off...
Excellent explanation.
Very good explanation
Kia bat hai bhai apki 👌
Beautifully explained like ever
Brother how to contact u, could u plz share ur email or nmber, thanks
very good. Thanks
Many many thanks for you.
Make a video on how to test it.
bhut aala.
Nice Explanation
Sir kia ecm ya koe bhi control module mpu k throw rpm ko daikh kr fuel open hota ha by actuator throttle no laod se full load tk plz reply me
jee bhai
Asad bahi sensers ke testing p video banay.
Bro 19 alloy wheels se 18 inch alloy wheels dal ne se ...speed sensor main koi problem ayaga kay ... please bro batao
Speed sensor flywheel k teeth se counting karta he
Jazak Allaha
Appreciated.
Good yr 👍
Sir How to bypass Rpm sensor... Only for simulation..... For CAt c9 engine
Nice video sir
Very good. Beta. T. Q.
thank you so much
How can we check the MPU . The coil resistance is between 50ohm and 1000ohms. Can you do a practical test regarding testing of MPU.
It depends on manufacturer. Mostly MPUs in Caterpillar are 150 ohms and some are 1 k ohms (1000).
I will do test later, but no now. because of lockdown.
Ok I'm using a magnetic pick up for Gas engine it's resistance is showing below 1000ohms. Can I test it by keeping it in front of a rotating drill machine with gear teeth
@@MysteriousCharms You can test it by measure its output AC voltage. During cranking voltage should be more than 1 VAC
Masha ALLAH
Sir, MPU ko troubleshooting kaise kare...
Nice..
Good
Thanks sir
Bhai iska connection bta do yrr kaun se wayer lagenge positive ya nagative signal kaun se lagenge
Sir ji kaya mpu kisi bhi company ka laga de to work karega ji
According to resistance hona chahye
@@AsadElectrical sir ji mpu kharaab hone ka kaya kaaran hai ji
Sir, some mpu's have three wires please explain what is the purpose of third wire.
3rd wire is for shield or ground wire. Used for ground the abnormal signals around the sensor
@@AsadElectrical ok thanks
Very nice
What is approximate resistance value of mpu used in komatsu PC 210
you can check with multimeter.
@@AsadElectrical what resistance value should Multimeter show in normal condition
@@rihabuljanat1994 Approx 150 ohms
@@AsadElectricaljust few minutes before i found it in service manual that it should be 500-1000 ohms.
If you want to c the page send me your WA Number
@@rihabuljanat1994 its ok. Because it is non CAT
Bhai ager mpu ki pulse ko lag karna ho to kase hoga
MPU ko counterclockwise rotate karain.
@@AsadElectrical bhai bina use turn kiye only electronic components use karke ho sakta ha kya
@@babbubatish0386 hosakta he try karlain. MPU ki supply AC hoti he
@@AsadElectrical bhai ager mare pass solutions hota to apse kyo pushta ma kase hoga bahi to push raha hu
@@babbubatish0386 Fan regulator laga k dekh lain
Sir ji mpu ko disconect kar de to dg chalega ji i means cranck hoga
Crank hoga
Nice post
Thank you sir lekin mpu ko fit karte samay hame kaise malum hoga ki mpu apne Range me fit ho gaya hai ?
Agar mpu kharab Ho jaye to kya engine start hoga?
complete tight kar k reverse turn karna he half round
@@AsadElectrical mpu kharab hone par kya engine start hoga?
Mpu ko alag se supply diya jata hai ya Jo AC volts produce hota hai usi par work karta hai?
@@jpsahni1338 MPU khud se AC supply generate krta he aur wo supply ECM/speed controller ko send krta he
@@AsadElectrical mpu kharab hone par engine start hoga ya nhi?
Kea sensor ko pahly sa dc suply mil re hote ha?
Nhi. Permanent magnet hota he
@@AsadElectrical jis sensor ko dc suply mil re hote ha 12 volt pher os ke kea lojic ha
@@fatimasehzadi5902 Please check videos on sensors. Thanks
th-cam.com/play/PLpLC-v4j8AHQV6QIUXb_RMe-Qgclkwlx_.html
asad bai agr magnet field ko teeth cut kr rhay hain...to coil me kaisay voltage paida hongay...coil ke hisaab se to field saakin position me hoga...agr teeth magnetic to coil tb field ko cut kray ga...field b mpu aur coil b mpu me....how is it possible? ke voltage paida hu...
Dear jo magnetic field around coil mojood he usko jab flywheel teeths cut karte hen to us me fluctuation ati he uski wja se coil me emf generate hoti he.
How to change frequency from 60 to 50 hz in perkins 2200 series?
th-cam.com/video/HX6cfuliJYw/w-d-xo.html
Thanks
Asad bhae is ki frequency kitny hoti hai
500 to 10k Hz
Asad bhai a t s ka control smjaen plz
th-cam.com/video/THf2ER7Ipr8/w-d-xo.html
th-cam.com/video/yg9r4esnacE/w-d-xo.html
ser genarator under speed shutdown ho raha Hai iska Kya reason hai
th-cam.com/video/dRLPDur8-xc/w-d-xo.html
Thanks
Sir g tractor mai 2 wire sensor h us kesy check Kia jay kaam nhi karta
th-cam.com/video/VoUWLrctEw8/w-d-xo.html
@@AsadElectrical thanks bhai
Sir mpu thek kam krta hy ki ni, kaisy check krty hy , kindly bta dy
Multimeter se ohms check krain aur engine cranking k time minimum 1 volt (AC) ana chahye
Thanks sir
Sir, generator frequency kahan se Sense krta hy,perkins ki bt kr raha hu
Running condition main HZ kitnay hoaty hain
Aur
Resistance ki value kitni honi chaiye
Resistance normally 100 to 1000 ohms ke darmiyan hoti he aur frequency check nhi karte volt check krte hen. 1 volt to 50 volt (AC) range he
@@AsadElectrical 35 series aur 34 series kay MPU ki resistance may difference hota ha
kia ya type change ha what?
@@muhammedkhan9311 34 Series (peec) me 2 mpu hotay hen. aik 150 ohms aur dosra 1000 ohms. 1000 ohms wala ECM (peec) ko signal deta he aur 150 wala panel ko. 35 series me 150 wala hota he
1000 ohms MPU 34 series k ECM ki waja se hota he
Sir MPU faulty hai kaise check karege
Check resistance with multimeter.
Sir resistance kitna aana chahiye
sir physically installation
Physical video is time nhi bana sakta
@@AsadElectrical sir mean jab ap ko time mily. as soon as possible.
Ram Ram
Bhai .. ap ne fly wheel k teeth ka cut karny wali bat sahi nahi btayi ha. Or ap ne faraday's law b theek se nahi samjha. When a conductor cut the magnetic field ..then e.m.f is produced in that conductor. (Ap keh rahy hain ..permanent magnet or coil dono same MPU k andsr hoti hain .lekin actually .. fly wheel k teeth me se kuch permanently magnetized hoty hain . Jo k MPU k andar wali coil ko cut krti ha ..or coil k andar e.m.f produce hota ha.
Thanks
Dear aap MPU ko aur flywheel ko dekhlena magnet kaha pe hota he. Phir dobara se meri video dekhna apka concept clear hojayega
@@AsadElectrical same for u
@@rodv7218 dear i am working on DGs since 2008.