Great tutorial! Ran into trouble around 24:10. The program said something about 0 thickness geometry. I got around this by extending the triangles beyond the surface. Thank you for these great tutorials!
У меня проблема решилась только когда я создала эскиз иначе - через восьмиугольник и квадрат. До этого - когда я создавала круговой массив, я узнала, что стороны треугольников, по неизвестной причине, были не равными (17.39 и 17.41) и ничего не помогало - происходила ошибка эскиза при любой попытке их определить. Ну и ещё я дорисовала отрезок в первом эскизе чтобы горизонтальные линии квадрата определялись.
Thank you for the good technique but I've question why didn't you use taper pin from tool box? Is there any logical reason? because your taper pin is not actually tapered.
i made the same by following your tutorial. thnks. can yoy provide me datas from where you make the parts i mean details regarding the dimensions, sketches etc. do you have any PDF in which all details of any part are given with the help of which i can also try making it
I did my four corner and after that i went to cut extrude and it does not fully cut extrude my four triangles! If you can help me out please do! Thanks i love these videos by you btw! Very helpful!
Sir can I borrow your file? for me to be able to pass my final requirements. I just dont have the money and laptop to do it. If you can borrow me. I will really appriciate it a lot. Thank you in advance.
Best youtube channel for solidworks❤
Great tutorial! Ran into trouble around 24:10. The program said something about 0 thickness geometry. I got around this by extending the triangles beyond the surface. Thank you for these great tutorials!
I'm also facing the same issue
Can u tell me how to solve it in detail
@@pandiyanb4025 bit late but I deleted the centerlines within the triangles and it allowed me to extrude cut after this.
У меня проблема решилась только когда я создала эскиз иначе - через восьмиугольник и квадрат. До этого - когда я создавала круговой массив, я узнала, что стороны треугольников, по неизвестной причине, были не равными (17.39 и 17.41) и ничего не помогало - происходила ошибка эскиза при любой попытке их определить. Ну и ещё я дорисовала отрезок в первом эскизе чтобы горизонтальные линии квадрата определялись.
i will really appreciate if you gave us a file that content the dimensions of each part of the design. overall the explanation is very good
Thank you so much! These videos are making my way through SW way easier!
Thank you so much Sir! It's really helpful to me❤
Super sir...I learnt how to draw many mechanical tools in solid works.
Thanks for ur video
Thanks sir to introduce assembly such a great drawing 🙂
...and I really enjoyed this tutorial, and thanks to you for this good and simplified explanation sir. Simple is better
Excellent helerious draw 👏👏👏👏👏
Thank you sir... It's very useful😊
Thanque sir your video is very beautiful
Well explained sir 👍
NICE SIR!!! I LEARNED SO MUCH FROM U TQ U.
Thanks Naveen M Hosamani,
The assembly is underdefined, is it still fine?
Many thanks. Good for beginners
Which Autocad software is this one you are using??
Thank you for the good technique but I've question why didn't you use taper pin from tool box? Is there any logical reason? because your taper pin is not actually tapered.
While extruding the cut triangles in fork,I am facing difficulty as it is showing zero thickness geometry.What should I do?
Nice video! I like it
Este video me salvo la vida jaja
Which program are u using
Useful tutorial. Thanks
Very nice sir
i made the same by following your tutorial. thnks. can yoy provide me datas from where you make the parts i mean details regarding the dimensions, sketches etc.
do you have any PDF in which all details of any part are given with the help of which i can also try making it
its simple drawing ,i lost jpg files, found in facebook.
can you refer any site or link where i can get datas or sketches or designs for designing mechanical stuffs.
Next you make the video is How do taper line will calculate ?
Very nice
great.. very good.. nd thanks
Nice video.Thank you
I did my four corner and after that i went to cut extrude and it does not fully cut extrude my four triangles! If you can help me out please do! Thanks i love these videos by you btw! Very helpful!
Taper is not shown in the taper pin..but anyway nice video. Much appreciation
Nice one sir
Nice sir
Its really good thank you sir
where is the taper in the taper pin and its holes
Fantastic
Please before starting give us the diagram show we can understand it in better way
Thank you very much
why is there no taper in the taper pin
rest all excellent
Start code
M117 Here We Go!!!
G28 ; home all axes
M204 P500 S700 T1000
M205 X10 Y10 ; set jerk x/y=10
M117 Purging Extruder...
G1 Z1.0 F3000 ; lift Z
G1 X0.2 Y25 Z0.2 F3000.0 ; move to start-line position
G92 E0 ; reset extruder
G1 X0.2 Y150.0 F1000.0 E15 ; draw 1st line
G1 X0.7 Y150.0 F3000.0 ; move to side 0.5mm
G1 X0.7 Y50 F1000.0 E30 ; draw 2nd line
G1 X0.7 Y25 F5000.0 ; quick wipe
M117 Printing...
End Code
M104 S0 ; turn off extruder
M140 S0 ; turn off bed
G1 X0 Y295 F1000 ; move finished print out front
M84 ; disable motors
M106 S0 ; turn off cooling fan
nice its very useful
What version of solidwork used in this video ?
During the mating ..Why not fully defined ? All in under constrained
I'm not getting the movement after mating the eye and fork. Can anyone please guide me? I have followed the exact steps that have been shown here!
Great!
best tutorial
Thank you sir
Although, video is wow
siema fajny rysunek
Very nice ppt
Thanks your time
Where is this part used?
sir cotter joint ki video nhi hai kya
still i didn't make cotter joints, i added in my list,
What is the different between choosing to draw using center rectangle and quarter rectangle? Plz...
And Thanks for making solidwork videos... learnt a lot from your videos more than my CAE professor...
Very good help me
Thanx
Diagram bhi dala karo
Okay!
Ajay Nadarge
the
Ajay Nadarge to
kohonir
Nice kno thama
How to define it fully?
ottomatic ladder assembly how to analishish
i will try,
K sir
How the f does he convert those lines at 11:10?
by use of convert entities
Sir please show the image of dimensions also
in which playlist section i find this
Thanks sir
nice sir
Ravi kumar Sah Add me as a contact on TH-cam. youtu.be/addme/ji4boOMv6rxC0sNrsOQIQfu-1cdMfQ
sir , please assembly practice ke liye, parts ki file mil Sakti hai....
Sir can I borrow your file? for me to be able to pass my final requirements. I just dont have the money and laptop to do it. If you can borrow me. I will really appriciate it a lot. Thank you in advance.
ya!
What is in Tagalog of Knuckles joint ?
Sir, I want contact with you
Sketch details ??
it's under defined
make it fully defined sir
Please show the diagram
i did exactly as you shown
even last time i copied you at a every second
but.................
Where os dimensions
Where is the reference question?
ok sir
i came to see tapering in this video..and he skipped it..useless for me
Tell in Kannada
Thank you sir
Taper is not shown in the taper pin..but anyway nice video. Much appreciation
i will rectify it thanks,
Thanks sir