I like the idea of the ESP32 board on the other side. It has 3 serial ports giving lots of possibilities. Program, communicate, debug, even a simple web server, (LoRaWAN) etc. I just got mine in the mail, can't wait to try it. Nice work! ~Jeff
Amazing work! Congratulations and tanks, it is very important for my projects, which involve sustainable development. I'm a beginner in the field, so forgive me if my doubts are silly, I ask anyway, because here in Brazil we say: there are no stupid questions, there are stupid ones who don't ask, lol. I am an Environmental Engineer, and LoRa, along with Sigfox, are essential for the realization of my projects, and for that I am very grateful 😊 About the E32 433MHz ttl-1w module, I'm having problems ... In the Datasheet it says that 1A of current is needed to feed it, do you use such a powerful power source? Did you add the transistors to correct the voltage? Can the entire circuit with resistors and transistors be replaced by converters of bidirectional logic level in Tx and Rx? Anyway, only with the material wue has available in your channel, they are a gold mine, because I am having problems with this EByte module (I bought it because it is 1W), but all other LoRa modules (all with SPI communication) , I managed to make it work thanks to your tutorials. Thank you very much!
@@CETech4u Hey Checked the other video too. That one is with ESP32. Do you have something to share on interfacing this LORA with Arduino? I really want to test and see these device working :)
Hello I have the right RF setting software for E32 modules and I get the ' No response from module ' error for some reason . Nothing wrong with the wiring between the E32 module and the ftdi, the COM port is always detected and the ftdi chip works fine. The port settings for the communication are also correct , baud rate / parity check / and so on.. Any ideas as to what might be causing this ? Great videos and channel. Thanks
Excellent video! I didn't catch in the video that both mode pins are supposed to be high to use the RF setting software from Ebyte and left them grounded thinking that normal mode was ok - I didn't get that far in the video yet :) . If anyone is getting an error connecting to this LoRa module (I used a USB to serial FTD1232 board) and you've verified COM port is set to 9600 baud, make sure both of those node pins are set high (3.3v). I was sitting there with my oscilloscope looking at the TX of the serial output (RX of the LoRa module), seeing the correct waveform being emitted from the Ebyte software and banging my head against the wall for over an hour... :)
CETECH, what is the difference between the EBYTE E32915T30D & the E329-5T30S besides physical dimensions. Also, where can I download your Arduino sketches to get started?
Fantastic teaching, please post video for ESP32, STM32 instead of arduino. These 2 have 12 bit ADC so we can measure analog in high resolution. Also please inform the modules shown in your channel is available for sale?
Hey, Yes it can be used to increase range but not of walkie talkie. As lora does not have so high data rate that can accommodate transfer of audio signal
Thanks for the detailed video. can u make a video using LORA (cheap one because we only may need distance up to 50m) for water tank level meter and automatic on/off solenoid motor with manual turn on/off switch?
@@CETech4u Thanks for the reply and yeah you got one more subscriber! btw i just realised we dont need to use LORA infact 433mhz RF transmitter and receiver will do the job as its range is around 100km and is cheaper as compared to LORA.
Have you done any testing with sleep mode (mode 3)? I'm trying to put the module in sleep mode except when I need to send data. For some reason, I'm only seeing every other transmission. I can upload an Arduino sketch to show how I am doing it.
Very good prj ! Just a question; how can I get the PCB from jlcpcb please ? Do they know the project or a PCB files have to be sent to them ? Thanks for helping
Hi bro great job, still extrememly relevent after 4 years thank you. by any chance could you please update the gitbub link or provide a link to download your Gerber files. many thanks
hey , can you tell me if you have some problems of alimentation with the 8km 1W module ? With my project, everything work well in 100mW but when i am using 1W module it make bug the system... I guess it is the 1W power but do you have other solution to give to me ? Can you tell me what is your power supply to power on the 1W module ? do the TTL level is important 3.3V or 5V ? thank you alot if you can answer to my questions
No awarness for students community as they blindly follow e-commerce websites, these sites sell 433 915 Mhz and our guys simply buy it. Semtech is the website one has to read and understand legal frequency ranges, then buy from websites. Prof in Engineering colleges even IIT, NIT have no idea on this LORA, curriculum is very old. so the students misguided by e-commerce sites. Still Indian govt not declared 865 to 867 as legal LORA range, but it license free for NFC, RFID so people use for LORA
I like the idea of the ESP32 board on the other side. It has 3 serial ports giving lots of possibilities. Program, communicate, debug, even a simple web server, (LoRaWAN) etc. I just got mine in the mail, can't wait to try it. Nice work! ~Jeff
Amazing work! Congratulations and tanks, it is very important for my projects, which involve sustainable development. I'm a beginner in the field, so forgive me if my doubts are silly, I ask anyway, because here in Brazil we say: there are no stupid questions, there are stupid ones who don't ask, lol. I am an Environmental Engineer, and LoRa, along with Sigfox, are essential for the realization of my projects, and for that I am very grateful 😊 About the E32 433MHz ttl-1w module, I'm having problems ... In the Datasheet it says that 1A of current is needed to feed it, do you use such a powerful power source? Did you add the transistors to correct the voltage? Can the entire circuit with resistors and transistors be replaced by converters of bidirectional logic level in Tx and Rx? Anyway, only with the material wue has available in your channel, they are a gold mine, because I am having problems with this EByte module (I bought it because it is 1W), but all other LoRa modules (all with SPI communication) , I managed to make it work thanks to your tutorials. Thank you very much!
Thanks for the wonderful video. I was struggling to make my 1w e32 work for a week and got the hint from this video.
👍🏼
Umm 8km is less even in urban areas , I doubt those antennas , did you check their resonance on a VNA?
Sir can you tell me the value of resistors you used in the PCB?
nice work. What is the register value for R9 and R10 to Pull M0 and M1 up. thank you for the video:))
yes i need to know that values also
How do I find out the RSSI value?
Thanks for sharing this. Awesome video waiting for next video with fully established connection, codes and communication between two Arduinos
The next video is already live on the channel. Check it out
@@CETech4u Hey Checked the other video too. That one is with ESP32. Do you have something to share on interfacing this LORA with Arduino? I really want to test and see these device working :)
Y de qué link bajaste el programa??
Cómo se setea la dirección y el canal?
Could you provide me link to configuration software?
how do i download the RF Setting software?
You are amazing bro!!!! In each video you provide very solid content. Thanks for everything. It is helping a lot😄😄
Hi, i have a question..
Does the Ebyte Sx1276 lora module work (send and receive data) without antenna?
Thank You so much for this Great Tutorial
can i get name of anten in this video?
Hello
I have the right RF setting software for E32 modules and I get the ' No response from module ' error for some reason . Nothing wrong with the wiring between the E32 module and the ftdi, the COM port is always detected and the ftdi chip works fine. The port settings for the communication are also correct , baud rate / parity check / and so on..
Any ideas as to what might be causing this ?
Great videos and channel.
Thanks
Can you receive information from different devices at the same time with one receiver? or collisions occur? thanks
Excellent video! I didn't catch in the video that both mode pins are supposed to be high to use the RF setting software from Ebyte and left them grounded thinking that normal mode was ok - I didn't get that far in the video yet :) . If anyone is getting an error connecting to this LoRa module (I used a USB to serial FTD1232 board) and you've verified COM port is set to 9600 baud, make sure both of those node pins are set high (3.3v). I was sitting there with my oscilloscope looking at the TX of the serial output (RX of the LoRa module), seeing the correct waveform being emitted from the Ebyte software and banging my head against the wall for over an hour... :)
Maybe a silly question : how do you make these 2pins (M0 and M1) high? Just connect them to 3.3v? Thanks for your clarification
@@GioBen68 yea
Good day sir, Can I asked a question, Is LoRa 32 can send and receive a data at the same time?
Thank.
How connect lora and ardunio the control in 2Servo and 2 led
hi i have e32 868t20d im try everyting but icant run it im check datasheet but not help me can u help me pls
Same issue here
CETECH, what is the difference between the EBYTE E32915T30D & the E329-5T30S besides physical dimensions.
Also, where can I download your Arduino sketches to get started?
Hi , can E32 module communicate with Ra02 lora module(in same frequency & sf ,....)? Given that we know both modules have sx1278 chipset!
Hi value resistor for transistor 3906?
i cannot get my modules to work pls help
great and simple
have you try to send a binary uart data?
what is the baudrate that you use?
is it possible to implement LoRaWan with Ebyte Lora devices?
Is this a full duplex module?
Value video about lora on youtube.!!! Thank you.
Channels kitane available he bro isame??
Plzz reply
Single
Fantastic teaching, please post video for ESP32, STM32 instead of arduino. These 2 have 12 bit ADC so we can measure analog in high resolution.
Also please inform the modules shown in your channel is available for sale?
can we use lora for increasing the range of walkie talkie communication? just to enable long range communication in remote areas ...pls reply
Hey,
Yes it can be used to increase range but not of walkie talkie. As lora does not have so high data rate that can accommodate transfer of audio signal
@@CETech4u okay...Thank you for replying!
Are these only Point to Point? If so, how do you pair them so that they only talk to each other?
No these are not point to point, no need to pair
Thanks for the detailed video. can u make a video using LORA (cheap one because we only may need distance up to 50m) for water tank level meter and automatic on/off solenoid motor with manual turn on/off switch?
Thanks for that! Do subscribe for more content like this..
I've added it to the list!
@@CETech4u Thanks for the reply and yeah you got one more subscriber!
btw i just realised we dont need to use LORA infact 433mhz RF transmitter and receiver will do the job as its range is around 100km and is cheaper as compared to LORA.
this is an amazing project and can i have the gerber file for the break out board of E32-433T LoRa module
This module communicates using UART whereas RFM modules are based on SPI
Can anyone compare please, which one is best and easy
WHERE IS THE SOFTWARE RF SETTINGS?
Have you done any testing with sleep mode (mode 3)? I'm trying to put the module in sleep mode except when I need to send data. For some reason, I'm only seeing every other transmission. I can upload an Arduino sketch to show how I am doing it.
just guessing from the video - but didn't he mention that the Tx module needs to send 2 messages? 1 to wake the module - the other for the data?
Very good prj !
Just a question; how can I get the PCB from jlcpcb please ? Do they know the project or a PCB files have to be sent to them ?
Thanks for helping
Download the gerber files from the GitHub page and then upload it on their website to get the PCBs
amazing work....please keep it up....eagerly waiting for your upcoming videos!
Thanks a lot!
Subscribe to my channel to stay updated when I release a new video!
@@CETech4u sure
Hi, the modules supports connection with lora gateway lg01?
Hey, haven't tried.
You Github link does not work, can you provide a working link please?
Our GitHub was hacked.
@@CETech4u Can you post the code somewhere please, otherwise there is no sense to keep the video up.
Hi. I am interested on the range that the 1 watt modules can achieve. Is it legal ?
The manufacturer claims the range to be 8km. Its legal here in India.
very informative tutorial video, looking forward for your complete project using this module and MCU.
Hi, can we have the code to do LoRa transmissions using Arduino? If not, whatever the code you used to make transmissions using this module?
Hi Paul,
Wait for this Sunday's video, I am making a video with interfacing this module with an ESP32.
:)
@@CETech4u That would be wonderfull. Is this the new LoRa chip or the older generation? THere is a new LoRa chip I hope you know that.
Which new LoRa chip are you talking about? Could you help me with the link or something relevant?
nice job, Where to find that gember file ?
In the description link of github is there :)
@@CETech4u thank you, indeed it was in the archive :) E32, thank you.
Can we use this module with esp 32 sir??? If Yes please make tutorial on integration of this module with esp 32 sir...... Waiting ..thank you sir
Yes it can be used with an esp32. Suggestion noted!
Subscribe to our channel to get notified when I release that video
@@CETech4u already subscribed sir Thanx for quick response.... Waiting for upcoming tutorial sir
@@CETech4u subscribed thank you sir
how can I buy your breakout board. Can i buy your board directly?
You can email me at akarshagarwal98(at)gmail.com
Hi bro great job, still extrememly relevent after 4 years thank you. by any chance could you please update the gitbub link or provide a link to download your Gerber files. many thanks
Our GitHub was hacked unfortunately. If you want you can email us and we can ship you the PCBs you need.
Men, el enlace esta caido! 😵💫🥲😥
hey , can you tell me if you have some problems of alimentation with the 8km 1W module ? With my project, everything work well in 100mW but when i am using 1W module it make bug the system... I guess it is the 1W power but do you have other solution to give to me ? Can you tell me what is your power supply to power on the 1W module ? do the TTL level is important 3.3V or 5V ?
thank you alot if you can answer to my questions
If you found any solution, could you share me please? I have an same problem
Great explanation for this module! Decoding the user manual was getting to be a chore :-)
Excellent video, thanks. May be worth reminding people to operate it from 3.3V and not 5V :-)
Oh yes, thats worth a reminder!
Please disassemble this antena. I am sure it has only 9 cm wire inside. 12 db??? So funny!
433MHz 1Watt is licensed band in India. Try using it for more than hour, u will find yourself in jail.
No awarness for students community as they blindly follow e-commerce websites, these sites sell 433 915 Mhz and our guys simply buy it.
Semtech is the website one has to read and understand legal frequency ranges, then buy from websites.
Prof in Engineering colleges even IIT, NIT have no idea on this LORA, curriculum is very old. so the students misguided by e-commerce sites.
Still Indian govt not declared 865 to 867 as legal LORA range, but it license free for NFC, RFID so people use for LORA