How to Remove and Replace an Ignition Lock Cylinder
ฝัง
- เผยแพร่เมื่อ 28 ส.ค. 2024
- How to remove and replace an Ignition Lock Cylinder on a 2003 Hyundai Elantra GT.
Please Consider Supporting My Channel at : / rnwdisclaimer:
Due to factors beyond the control of Ratchetsand Wrenches, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Ratchetsand Wrenches assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair video's. Due to factors beyond the control of Ratchetsand Wrenches, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again Any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Ratchetsand Wrenches.
Well, I managed to change it out. It's a bit different than the video...different way to take the dash cover off. Then I managed to find the slot to push the lever. It was very tricky to get in there. I used part of the inside of a pen, which was short and fit in the hole okay. Needed to give the cylinder a good tug to pull it free (I almost gave up). Sadly, it did not fix my issue, which I know am pretty sure has to do with the timing chain ugh...but I feel awesome that I managed to do this anyway (especially considering that I did not know know how to undo the negative battery terminal). Thanks so much for the video.
you can try drilling out the tab or drilling into the lock cylinder around where the key broke off to make room and try to get the broken piece out somehow! Also you can just replace the whole ignition lock with the assembly it goes into! Its connected to the steering column with two snap off bolts I believe, use a chisel and a hammer to try to get them to turn! I guess before doing that you can always use the hammer and chisel to try and break and turn the ignition cylinder. GL
Super helpful! Thanks so much! my roommate has this exact car and you just made him feel relieved that we don't need to call a lock smith.
Nicholas Stephens Sweet, glad the video will save you some money. Thanks for commenting, cheers.
@@myRatchets I’m watching your videos I like it.I have question about Dodge Grand Caravan 2013.Sometime when I start my car.The car turns off by itself.Do You Think that’s the problem with my ignition lock cylinder.Sometimes when I’m driving my car just lose power.Thank and I hope you’re giving me answers.
thank you so much. I just took mine out of a 95 corona. it was super stuck so put a screw driver though the hole in the key for leverage. just saved me a call out fee.
Thanks for the video. 2003 Hyundai Santa Fe is very similar. To replace that ignition lock cylinder you will need to loosen the 4 bolts holding the steering wheel column. This pivots the column down allowing you to remove the cylinder (the white connector on top hits the dashboard).
Great piece of info, thank you!
Ok. Thank you for the video!! One more question. If I get a new ignition, would I have to change anything else? Will it just lock back in place and start up?
That's a lot less work than I imagined. I originally thought they were permanently fixed to the steering lock mechanism, and needed to be drilled out or something. Thanks for the good news and the explanation.
Hyundai elantra are all the same from 2001 to 2006 I just took an ignition out of a 2001 auto elantra and put it in my 05 elantra that is a 5 speed with keyless entry and it works great if anyone was wondering.
Iam Your Newest Subscriber Great Videos
Greetings to you. Theron Here, i watched your video of how to remove ignition switch. It was very informative. I have a question today. What happens if i remove my 2007 Suzuki swift ignition switch and replace it with another used ignition switch which cames with its keys,
Will i need to replace the computer box also?
Thanks in Advance
Following from Mombasa Kenya Magufuli locksmith
Thank you so much.
This helped me change it easily.
You are a life saver. Thank you so much
Hi can you still do this even if you don't have the key to your car?
Can you explain how to remove the housing off the column also ? For a 2002 Hyundai Santa Fe
I did a quick search and couldnt find any either, your best be is your local junkyard or dealer. Sorry
What If I dont have a key? Can I still get the ignition cylinder out?
Very helpful video, thank you so much:)
What if you lost the key?
Would you be able to do this without the key because I lost my key and now I am thinking about changing my ignition lock with a new set of keys!
hmm, Probably not without damaging the lock cylinder (drilling.etc) why dont you just a someone to make you a key? it'll be easier and maybe even cheaper. If you shop around you can find a deal I am sure. GL
Ratchets And Wrenches ,anyone know how to change one on a 1996 Jeep Grand Cherokee?
Do you have anything for replacing the ignition switch for a santa fe 2006? Also would it have to be coded?
Hello Sir, Thanks for this video. I have a 94 Camry, and am having issues with the wheel locking up while on. At the end of this video, I see that you tighten down the white housing and button. Need I do the same on mine or is that specific to these Elantra's? Thanks for any input. Your videos are great. Cheers. Bobby :)
Hello... Thank you for video on how to replace ignition. My 2004 Toyota Sequoia ignition is not turning over to start car please help me... Thank you.
Thank you mate ❤
My key snapped off in the ignition and it's deep in there. I have to replace the whole thing don't I? 🙄
I have a tripod but in this video I just rested the camera against the passenger seat.
Dont quote me but I think you should be alright even if the car has an alarm system. GL
Good voice. Did you use a tripod?
Great video thank you. Can you do this procedure if the steering wheel is locked and key does not turn (into acc mode). I mean if that pin does not go all the way in and I cannot turn the key to make it go all the way in... what then? EDIT: I have removed everything but the pin does not go in and I cannot turn the key. Do I have to drill it? Is that the only way?
I am having the same issue.
if you have no keys to turn to correct position get a drill and small screw driver.jam the screwdriver in against the retaining pin to stop it spinning and then drill it out.replace with new ignition if you don't have a replacement pin.
Can I remove the ignition without the key?
Situation is unique. The current ignition is already a replacement & may have lost even the spare.
Thank you so much
Everyone says the same "put the key in accessory" but on mine it won't turn at all.
Ratchets And Wrenches hi, do you think is there a way to remove the ignition without car keys since I lost mine?
I wonder if it's the same in a 2005 Elantra. At least the A/C panel looks exactly the same.
I have a 1998 toyota camry. When replacing ignition switch it came apart. I am having trouble putting it back together. I believe I have it correct but still won't work. There are 5 small springs and 2 small bearings. Do you know how it goes back together? Or do you have any idea where I could find it out. Thanks. Also it has two copper discs. One small and one larger. It seems to me it can only go one way. I am not sure I found all parts.
Show less
REPLY
I can't find the ignition anywhere, even at the dealerships! I have to move it from where its at that's why I was asking.
Would it work still if the key is broken inside.?
Hi, I was wondering on a 2002 Chevy cavalier. If the key wont turn all the way to crank the car, could it be the ignition cylinder or something else?
More than likely yes. GL
Is this the same way to take out a 03 sonata ignition lock cylinder?
Thanks
Is it possible to start the car, without the ignition? With some skinny nose pliers?
Any information about a 2000 Elantra? I'm currently trying to pull mine apart without wrecking it. No info on the net, like 90's Elantra's and 2001 and up but nothing on 2000.
No sorry, but they should be similar! Does it have tab anywhere?
RatchetsAnd Wrenches No, there is 2 roll pins to extract. I've managed to get it apart but it was difficult. I have to weld a part of the housing back together and the roll pins needed to be drilled to pull the cylinder out. I found out the release arm for the key and the mechanism for the steering lock needed to be worked to operate smoothly again.
is there any way taking off bolts from bracket with out drilling hole?
use a center punch and hammer . tap the bolt head in anti clockwise direction to loosen them .
Does this work for 2002 Hyundai Santa Fe
So I never done it before and my car ignition is sort jam. I looked up autozone for ignition lock cylinder and it come with keys. My questions is would the key be the same as mine? Would it be able to open my door with those keys?
No they will be different keys
thanks
Oke good lah pokok namah
What happens if you don’t have the key it’s been lost
Would this be the same process for a 2003 hyundai sante fe?
Trying to remove a broken key from a Hyundai Tucson 2008 ....the key was cold and broke in the ignition
I lost my keys. Is it possible to do this without the key??
Same question
Nope
what if you font have they key? thats why i have to replace the lock-keys were lost to an already replaced cylinder......
Good video
thanks!!
could u please do one for a 2000 sonata when I turn the key it just makes a click sound after a few tries it turns over but I have to wiggle the key
+Eric Steele Check your ignition switch, wiggle the wires at the end of the lock cylinder next time it does this and if starts up you need an ignition switch (electricl part of the assembly not the lock cylinder) also check out a video on my channel named How a cars starting system works for more info. gl
thanks
I have a 2002 BMW X5 need to replace the ignition Lock cilender
What if the ignition switch does turn over ? What do I do ?
Doesn’t turn to ACC ?
Wat if my key goes in but doesnt turn the cylinder?
942doc1 easy fix...sorry just realized this is 3 yrs old
what years are interchangable
What if you have a broken key
If it's a transponder system, does removing the ignition to thoroughly clean the lock and then reinstalling the same ignition cause any problems, or should it still work fine, in terms of programming?
My truck was broken in to so some body that was a rookie jam my ignition switch how my key won't go in at all so how can I get it out to put a new ingition switch
Same here... Key won't turn at all. Anyone have an idea how to remove these in this situation. Mine is a Honda.
i would like 2 kown if u canshow on a 1973 ford mostan
What if i dont have a botton but roll pins
My ignition cylinder has something jammed in it . So my key doesn't go in all the way and doesn't turn. How can I remove the cylinder in my situation?
Patricia Lujan have you settled this? Iam having the same problem as yours
Do you know where I ca n find a replacement ignition lock cylinder? I've looked everywhere, I can't find one anywhere. I need one for a 2003 Hyundai Elantra.
Did you ever find one triple og triple og ????
looking to take out ignition switch on a 1973 Porsche 914
William Dighton Havent worked on one of those. GL let us know how it goes.
what if you don't have a key
How about a 2015
what if the lock cylinder is damaged from an attempted theft and key can't be inserted/turned? thanks.
00 sephia
Lone Wolf you can either replace the entire assembly or drill into the cylinder break it and turn it out. Than insert your new cylinder, gl
ditto lone wolfs issue, ''drill into the cylinder break it and turn it out''. exactly how would you do this?
did this work for you ?
yes, drill directly into the center of the lock (imagine drill bit is your key). once you get so far in, step up the size of the bit. once you start doing it, you'll get a feel for it and see the results. the ignition cylinder will crumble and break a part and fall out. get one of those magnetic tip extendable tools and use that to pick up any leftover broken pieces and shavings. Put the new ignition cylinder in(optional), still using a screwdriver to start my car. LOL
great thanks
Can you do one for a 2007 Entourage, please and thank you.
and how about the problem of having no keys lol how can i get it into accessories then?
what is you have no key and that the reaSON YOU WANT TO CHANGE IT
Fiat pallio cannot remove key cylinder
I lost my key
how can you replace it without the key
The same way. New lock cylinder comes with new keys; you don't need a key to remove the lock cylinder.
Do u need to reprogram anything
That helps if I had the key lol
why’d yall delete my comment, i meant it in good fun 😔