How to Replace Rear Exterior Door Handle 05-10 Chrysler 300

แชร์
ฝัง
  • เผยแพร่เมื่อ 3 ม.ค. 2025

ความคิดเห็น • 69

  • @1AAuto
    @1AAuto  4 ปีที่แล้ว +3

    √ *Watch the Video*
    √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
    √ *Do it Yourself*
    √ *Save Money*

  • @OvieSnipez8
    @OvieSnipez8 3 ปีที่แล้ว +9

    Spent at least 2 hours doing this, done step by step. Saved me cash that’s for sure. Great video. Thank you for helping.

  • @dbustamante8425
    @dbustamante8425 3 ปีที่แล้ว +7

    Thank you so much my husband didn’t think I can change it but three hours in and I did!!!🤗👏🏼

  • @glennsage2881
    @glennsage2881 5 ปีที่แล้ว +2

    Thank you - your instructions were very helpful. We just finished this job! It took my wife and I exactly three hours. Here is our post-mortem. We avoided having to remove the entire Water Shield, and were able to lift up just the lower half and access everything. We also were able to avoid removing the latch and window guide. We were replacing the front passenger exterior handle. Not having a small ratchet to fit in the tight space was a problem, but we improvised a small Vise grip holding onto the 5/16 socket perpendicularly. Another hassle was with the retaining clips, we fortunately had purchased a kit of assorted retaining Clips to replace the ones I mangled!

  • @Daniel-mq3kb
    @Daniel-mq3kb หลายเดือนก่อน

    I have watched many of your instructional videos. I find them very well made and have helped me learn quite a bit about repairing my vehicles. In todays economy it is helpful to cut costs in minor repairs that would cost hundreds of dollars. I live in Canada so I am unable to buy parts from your outlets. Thank you very much.

  • @intp
    @intp 3 ปีที่แล้ว +2

    Thank you for the great instructional video. I did run into one issue that I think others can avoid with this suggestion: Before you reinstall the water shield test that your window goes down all the way smoothly. I didn't and discovered that at about 60% open my window now slowed down almost to a stop and had a lot of trouble getting all the way down and then back up. I had to take off the panel and water shield again and re-adjust the metal and rubber window guide.

    • @1AAuto
      @1AAuto  3 ปีที่แล้ว

      +intp Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

  • @talesofthecentralcoast
    @talesofthecentralcoast 2 ปีที่แล้ว

    A+ did not think i could do this. had my ipad by me and paused it every step of the way! thank u saved me 200

  • @doopik.6551
    @doopik.6551 7 ปีที่แล้ว +5

    Very good demonstration on how to disassemble every part! Thanks for the guide.

  • @bigkev1004
    @bigkev1004 6 ปีที่แล้ว +2

    Just did this step by step on my wifes car while watching the video, made it pretty easy, thanks 1a auto👍

    • @1AAuto
      @1AAuto  6 ปีที่แล้ว

      +Kevin Prince Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/chrysler-300-dodge-magnum-exterior-door-handle/i/1adhs01455?TH-cam&CTA+Comment&RjqWXwWFouE

  • @minxcollector
    @minxcollector 7 ปีที่แล้ว +1

    Good video as always Guys thanks. One thing for us poor sods in the UK whose cars suffer with the elements and naff salty road grit, the interior glass support does not slide down after loosening the bolts - Rust! the rubber becomes held fast so use a slim trim tool or wide flat screwdriver slide up from underneath between the rubber and metal support frame to free it. I was pulling and levering through the holes for quarter of an hour before the light dawned!!

  • @emilaznar526
    @emilaznar526 3 ปีที่แล้ว +1

    Excellent. Easy to follow. Gives me the confidence to do this myself and save a barrel load of money.

  • @305youtuber
    @305youtuber 3 ปีที่แล้ว +2

    thanks, changed the one handle needed it and now it's working just fine 👌, i can imagine what the dealer would charge for that 😳

    • @juliodelgadillo8510
      @juliodelgadillo8510 3 ปีที่แล้ว +1

      Fr lmao I'm about to change mine today hopefully I do it right lol

  • @snuz9974
    @snuz9974 ปีที่แล้ว +1

    Don’t overcomplicate things… After you remove the window guide just loosen the door latch and you can access all 3 bolts and remove the handle…

  • @williamsedwick790
    @williamsedwick790 6 ปีที่แล้ว

    great video and instructor, had to change both front and rear handles,without these video it would had to go to dealer,saved me a bunch of money, thanks so much

    • @1AAuto
      @1AAuto  6 ปีที่แล้ว

      +William Sedwick Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com

  • @chriswilliams2743
    @chriswilliams2743 4 ปีที่แล้ว +1

    Thanks so much for making this video. I reckon you just saved me over 200 quid. Will definitely recommend you to my friends. :)

    • @1AAuto
      @1AAuto  4 ปีที่แล้ว

      +Chris Williams Thanks for checking us out! 1AAuto.com

  • @mikebennett3812
    @mikebennett3812 3 ปีที่แล้ว

    Fantastic videos and great service all round.

  • @niner4lyf
    @niner4lyf 4 ปีที่แล้ว +1

    Thank you so much! This helped out a lot!

    • @1AAuto
      @1AAuto  4 ปีที่แล้ว

      +Nunya Biznaz Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

  • @corradosoprano8677
    @corradosoprano8677 6 ปีที่แล้ว +2

    Thanks for this vid. Instead of removing the door latch all the way out, u can just remove the 3 t30 bolts. Move th door latch down out of the way just a bit and you can access all 3 bolts to remove the door handle.
    Might be possible to just do that instead of going through all the steps in the video but I'm not sure because I was following along step by step as this was my first time doing this job.

  • @davidlarcombe5333
    @davidlarcombe5333 6 ปีที่แล้ว

    Just had to replace one of mine, this was a great help. Pity Chrysler seem to make things as awkward as possible to work on.

    • @1AAuto
      @1AAuto  6 ปีที่แล้ว

      +David Larcombe Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/chrysler-300-dodge-magnum-exterior-door-handle/i/1adhs01455?TH-cam&CTA+Comment&RjqWXwWFouE

  • @winguicaquias7117
    @winguicaquias7117 7 ปีที่แล้ว +2

    Is neccesary remove the part with the T30 screws to remove the door handle only? Thanks for the video

  • @StHella-xf3yr
    @StHella-xf3yr 7 ปีที่แล้ว

    Awesome step by step video 😊👍🏾

    • @1AAuto
      @1AAuto  7 ปีที่แล้ว

      +St. Hella Thank you for checking us out, and the compliment! 1aauto.com

  • @welchlbrandon
    @welchlbrandon 3 ปีที่แล้ว +2

    You 100 % do not need to do all that to get the handle out

  • @serioussi
    @serioussi 5 ปีที่แล้ว +5

    Handle covers it is :D

  • @JustinMentionedIt
    @JustinMentionedIt 3 ปีที่แล้ว

    7:33 I guess they drilled the holes different in my 06 oddly, bc there’s absolutely no way I could use an extension and take those two screws out bc the hole in the door isn’t even close to lining up like that I had to do it inside the door

    • @1AAuto
      @1AAuto  3 ปีที่แล้ว

      +Justin Peyton Thanks for the feedback!

  • @celestelevi5116
    @celestelevi5116 7 ปีที่แล้ว

    Your videos helped my chrysler couple times already, could you please tell me, if I want to replace that interior door chrome accent(near door handle), do I need to remove door panel first or can I take it out just using those plastic tools for removing trims?

    • @1AAuto
      @1AAuto  7 ปีที่แล้ว

      +Celeste Levi Thanks for watching! That piece of trim is most likely a pop-in piece that can be pried off. You just want to make sure you do not have to release any sort of clip that is on the other side of the door panel. 1aauto.com

  • @johndudeff2622
    @johndudeff2622 6 ปีที่แล้ว

    I watched the video on replacing the rear passenger door handle on an 05 Chrysler 300c. It was big help. I am trying to put the window guide back in and it seems to be stopped by a rubber strip. This causes the top screw not to drop into its slot. I am unsure where this rubber strip goes. It looks like it might be for the glass to slide through. Does it fit into the metal window guide track. The video does not show it in the replacement. Any help is appreciated.

  • @johnsteinbauer9694
    @johnsteinbauer9694 6 ปีที่แล้ว

    I viewed several videos before I attempted to RR rear driver side door handle and this one was the best by far. I had previously replaced the driver door handle without too many problems but the rear seemed a lot harder. My only suggestion would be to spend more time on removing and replacing the three latch rods and also provide a diagram with the electric lock and latch assembly showing the rods with the color retainers. It appears some type of small camera was used to show the interior of the door where the lock and latch assembly is located..which is great but when trying to determine how to re-attach the rods and retainers, it was hard for me. I also had a problem with the rubber window guide getting in the way of re-installing the assembly but then realized it was easier to do it from the lower hole first then grab it from the upper to put it in place. It would also be helpful to be advised of all the wrong way to reconnect the rods so they could be avoided. Maybe it's just my lack of mechanical aptitude that caused problems...but finally got it done with no extra parts. I did somehow lose the rubber piece that goes next to the electric assembly..probably fell down inside the door never to be found. Would like to know if this rubber part is critical and the purpose.
    Thanks.

  • @marinasip908
    @marinasip908 5 ปีที่แล้ว +1

    What do I do if my door won’t open from the inside now 😕

    • @1AAuto
      @1AAuto  5 ปีที่แล้ว

      +Marina Sippola We would suggest go back and double check to make sure everything is connected properly and a latch was not dropped into the panel.

    • @NvonK277
      @NvonK277 5 ปีที่แล้ว +2

      You probably just need to un engage the child protection lock On the inside of your door

  • @peace-yo4no
    @peace-yo4no 7 ปีที่แล้ว

    thanks awesome video ,,,

    • @1AAuto
      @1AAuto  7 ปีที่แล้ว

      +Gus Tafoya Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/chrysler-300-dodge-magnum-exterior-door-handle/i/1adhs01455?TH-cam&CTA+Comment&RjqWXwWFouE

  • @lashandaspencer5451
    @lashandaspencer5451 4 ปีที่แล้ว

    Having trouble making the panel fit back smoothly on the door. Any suggestions

    • @1AAuto
      @1AAuto  4 ปีที่แล้ว

      +Lashanda Spencer Are you referring to the door panel? Just make sure all of the clips are not broken and bent.

  • @seand21342134
    @seand21342134 7 ปีที่แล้ว +2

    Everything worked, but I have a huge problem and need to know if there's a solution. I closed the door to test everything, and apparently I must have forgotten to hook up one of the latch rods and now the door is stuck closed. Can anyone help?

    • @1AAuto
      @1AAuto  7 ปีที่แล้ว

      +Sean You may have to remove the door panel so that you can reach inside and pull the door latch rod to pop the door open. Hope this helps you out. 1aauto.com

    • @1AAuto
      @1AAuto  7 ปีที่แล้ว

      +Sean You may have to remove the door panel so that you can reach inside and pull the door latch rod to pop the door open. Hope this helps you out. 1aauto.com

    • @seand21342134
      @seand21342134 7 ปีที่แล้ว

      1A Auto Parts I haven't tried yet, but can I get the panel off while door is still stuck shut?

    • @seand21342134
      @seand21342134 7 ปีที่แล้ว

      1A Auto Parts I haven't tried yet, but can I get the panel off while door is still stuck shut?

    • @seand21342134
      @seand21342134 7 ปีที่แล้ว

      I got in FINALLY! I was able to hit the child safety switch. Now i can open the door, but only from the inside

  • @ameehasa5504
    @ameehasa5504 6 ปีที่แล้ว

    How to adjust the handle with wire I push the handle very hard so can open the door the wire adjustment

  • @youngcgang5437
    @youngcgang5437 3 ปีที่แล้ว

    What happen if the door handle broke and it’s not opening the door on the inside either

  • @CM-qq3eg
    @CM-qq3eg 6 หลายเดือนก่อน

    If your door is stuck closed like many chrysler 300s this wont help you changce the handle to get it open

  • @ruthschroeder6915
    @ruthschroeder6915 3 ปีที่แล้ว

    Just did mine and I'm a girl so easy

  • @scotgeorge3877
    @scotgeorge3877 3 ปีที่แล้ว

    You skipped over the tool to pop off the white trim clips

  • @breezylackey731
    @breezylackey731 7 ปีที่แล้ว

    I got it all put back together and my inside door handle won't open the door now. What happened??

    • @1AAuto
      @1AAuto  7 ปีที่แล้ว

      +breezy johnson Thanks for watching! If the interior handle does not work you should inspect the inside of the door to see if a rod/cable has become detached. www.1aauto.com/chrysler-300-dodge-magnum-exterior-door-handle/i/1adhs01455?TH-cam&CTA+Comment&RjqWXwWFouE

    • @Crumy-z5i
      @Crumy-z5i 7 ปีที่แล้ว

      breezy johnson is the rod, he doesn't say which end goes in first. Might have put it in back words and it popped off

    • @hudsonm3498
      @hudsonm3498 6 ปีที่แล้ว

      Had the same problem then realize the child lock got set when I bolted the latch assembly with the torx screws. It would not go back down. I went back to loosen it up and locked the doors before I put it back in place. Double checked to make sure I could lock and unlock the child lock. That worked for me.

  • @imreptar7038
    @imreptar7038 7 ปีที่แล้ว

    u went a little to far lol, u dont have to remove the whole door lock/latch assembly.

    • @1AAuto
      @1AAuto  7 ปีที่แล้ว

      +Sabin OwnzU Thank you for checking us out. The removal of the door lock and latch assembly was part of a separate video we were completing. 1aauto.com

    • @hudsonm3498
      @hudsonm3498 6 ปีที่แล้ว +1

      Thanks for making a note of that. I’m reviewing this and another video to lessen any pain so not removing the lock/latch is good to hear