Gracias camarada por el video es de mucha alluda ya pude sacar una cadena de oro de la parte de abajo que estaba atorada gracias saludos desde Califas..🙋🏻♂️
I have the same exact washer and my machine won’t agitate, the drum is free spinning and I cannot get the agitator off even tho I do have the screwdriver through the hole?
I’ve got the hole lined up with the round dimple on the lower collar but my screwdriver wouldn’t go through, so I lined them up again and got my phone down in there to take a picture and see if there was a reveal but even with the hole lined up with the dimple there is no hole on the lower collar. Any idea where to go from there?
@@jacobcurry4931 sorry for the late reply but I found another resource that explained that some of the newer models have an agitator that is identical but you actually have to punch the hole through with a screwdriver once you line up the dimples.
sorry for the late reply. both have good machines but Whirpool came out with a new model which you can have an agitator or press a button on the agitator to remove. so that will give you both options in one Machine.
ok yeah im right at this spot seen video where screw driver is not needed at all but guy uses align marks as squeeze point plastic deforms just enough to right spin it right off of course i cant get it to go and middle alignment mark ring only moves slightly so no way for all three to align i'm about to just cut it off and get wholle new agitator
@@mayraromero2808 did remove it by drillin o e inch paddle bit through top of aggitator to reveal bolt atbotton used extenstion socket it came off with a impact movement took out aggitator a d used 4inch channellock to squeezean turn came tight off while standing on it had to cut off retaining nut with that highspeed ryobi vibration cutter bi metal blade carefull took two sides off that thing snapped off kaPing! then droped the transmission and replaced
@ Mayra Romero yeah ok did all that r&r the trannythe clutch and some electric plug in stuff and the lid switch ALLL if which did not fix my original problem lid switch and speed indicator and was not filling to deep fill and not draining on the spin sooo all that and still not working looking at the main control board r&r only reason i replaced tranny because obvious seal failure (spun streakmarks) a kind of mud all over the motorcompartment wasnt there before
You explained it the best!!
Thanks for the quick video, mine was gummed up so bad I had to heat up the area where you put the strap wrench with a heat gun so it would break free.
I tried everything to remove the auger. I about gave up till I saw this video. I bought the strap wrench it came right off. Thanks so much.
Awesome.
Gracias camarada por el video es de mucha alluda ya pude sacar una cadena de oro de la parte de abajo que estaba atorada gracias saludos desde Califas..🙋🏻♂️
Thanks man i appreciate you so much😊
Glad I could help
I have the same exact washer and my machine won’t agitate, the drum is free spinning and I cannot get the agitator off even tho I do have the screwdriver through the hole?
I’ve got the hole lined up with the round dimple on the lower collar but my screwdriver wouldn’t go through, so I lined them up again and got my phone down in there to take a picture and see if there was a reveal but even with the hole lined up with the dimple there is no hole on the lower collar. Any idea where to go from there?
I’m having the same problem
@@jacobcurry4931 sorry for the late reply but I found another resource that explained that some of the newer models have an agitator that is identical but you actually have to punch the hole through with a screwdriver once you line up the dimples.
Would you recomend a GE profile washer or Whirlpool? Agitator or Impeller which is least likely to have issues? Thanks!
sorry for the late reply. both have good machines but Whirpool came out with a new model which you can have an agitator or press a button on the agitator to remove. so that will give you both options in one Machine.
ok yeah im right at this spot seen video where screw driver is not needed at all but guy uses align marks as squeeze point plastic deforms just enough to right spin it right off of course i cant get it to go and middle alignment mark ring only moves slightly so no way for all three to align i'm about to just cut it off and get wholle new agitator
So what happened am at the point you where at to cut it off .
@@mayraromero2808 did remove it by drillin o e inch paddle bit through top of aggitator to reveal bolt atbotton used extenstion socket it came off with a impact movement took out aggitator a d used 4inch channellock to squeezean turn came tight off while standing on it had to cut off retaining nut with that highspeed ryobi vibration cutter bi metal blade carefull took two sides off that thing snapped off kaPing! then droped the transmission and replaced
@@mayraromero2808 the high speed cuttr for was to remove the tub from tranny
@ Mayra Romero yeah ok did all that r&r the trannythe clutch and some electric plug in stuff and the lid switch ALLL if which did not fix my original problem lid switch and speed indicator and was not filling to deep fill and not draining on the spin sooo all that and still not working looking at the main control board r&r only reason i replaced tranny because obvious seal failure (spun streakmarks) a kind of mud all over the motorcompartment wasnt there before
🌹 ρɾσɱσʂɱ
I need to try this method. I want to remove it to clean under the auger base.