GE Washer Agitator Removal - How to do it and access the GE Washer Hub and More
ฝัง
- เผยแพร่เมื่อ 6 ม.ค. 2021
- Today, we had to replace a GE Washer agitator which meant that we had to take it out, which isn't easy to do on these newer-style washers. No one else has (seemingly) done a video, so I thought we'd do that when we got the new GE Washer Auger from Appliance Parts Pros.
All you need to do a GE Agitator Repair is a screwdriver, and the new agitator itself. The big problem with this is that you MUST remove the agitator if you want to do anything involving the GE Washer Hub, or a GE Washer Tub, or GE Wash Plate - the screw keeping everything in place is hidden under the agitator which is a major problem.
This video only involves the agitator / auger itself, not the hub. However, those are almost self-explanitory, and the big issue is what's shown in the video. I hope this helps you with your GE washer, as it was a real pain to figure this one out, as all newer style GE's have this issue which isn't really discussed much how to solve.
Buy this GE Agitator if yours is bad for a newer-style GE Washer (WH43X31240): bit.ly/2KRMY9r
You can buy appliance parts w/ a great warranty at: bit.ly/3pVxWyX
If you like the hat, buy a hat! bit.ly/3dtHHjE
(Note: The hats are meant purely as parody, and are not an endorsement for a person, politician, or party)
Tools I use in all videos can be found at my Amazon Idea Page: www.amazon.com/shop/bensappli...
Did this video help you out? Send me a tip, and help me make more Appliance Repair videos for people to watch for free!
PayPal: paypal.me/BensappliancesYT?lo...
CashApp: $BenjaminSchlichter
DISCLOSURE: This post may contain affiliate links, meaning when you click the links and make a purchase, we receive a commission. Affiliate Link & Earnings Disclosure: bit.ly/3oXeu3B - แนวปฏิบัติและการใช้ชีวิต
Thanks Ben for the video! A correction though, you said towards the beginning of the video to turn it counter-clockwise to remove it, that is incorrect, you need to turn it clockwise(to the right). Also, make sure you have a good sized screwdriver for the hole, the closer to the diameter of the hole the better, a small screwdriver will be too loose. One more thing, if you need to do this by yourself, after you get the screwdriver in, use two hands and grip the bottom of the agitator, spread out your elbows to contact the sides of the drum to act as brakes, then twist the agitator to the right while still holding the drum with your elbows. That worked for me, I did loose some arm hair from the friction, but it worked. I hope this information is helpful to someone!
Thanks for that . I was not sure which way to turn.
I still could not get this agitator off, whenever I turned it hard it would wedge the screwdriver diagonally in the hole
I am having the same issue. Were you able to figure out what was happening?
I noticed that mistake also.
I am reefing on mine like crazy and it won't come out, it's driving me nuts!
Ben, you are the MAN! This is exactly the right instruction video, at the right time to undo what my domestic goddess managed to do. Somehow the curtain she washed wrapped itself partially under the agitator. Removing the agitator is the only way that will allow me to remove the aforementioned curtain with minimal damage. Thanks.
Saves us a lot of grief in the learning process.. in this amazing world, of amazing people. Helps us get around some of the planned obsolescence issues of expense. We understand why.
Thank you. They delivered a brand new washer and the agitator came off first use. Everything closed until Tuesday. Were headed to Laundromat and I found this. Thank you.
Never would’ve been able to do it without this video. Thanks
Thank you so much for the guidance, even with the knowledge it wasn't easy, very hard to turn. However, very successful thanks to you.
Thanks for HELPFUL and saved me a service call! Very concise and easy to follow 😊
I love the features on my new GE washer, had to replace the machine twice within a month. The agitator comes off during the washing cycle. New machine with problems; I am switching brands. Thanks for sharing.
Thanks! Helped my dad and I fix our broken washer agitator base. Only thing is it was clockwise not Counter clockwise. Thanks!
I used a rubber strap wrench along the base with the screw driver inserted. Thanks your the best.
Hallelujah for this video! This will definitely come in handy in the future, I'm sure.
Thanks for the diy video. Saved me a service call cost and able to order a new part
Thanks brother for showing us the video I appreciate it but I still couldn’t get it off so I just broke the agitator off to get to that bolt because I had a new agitator to put on thanks 👍🏾
Appreciate the video was trying to figure out how to take it off forever
Just the info I needed tonight! Thanks
Thanks Ben, for the video! Sending a tip for anyone having trouble with this process. I could not poke my screwdriver through the auger/agitator. So, I got out my drill and drilled through the auger. I still didn't have enough leverage so I then drilled through the exact opposite side of the auger, using the inserted screwdriver as a guide to find the opposite side. Once the holes were drilled on both sides, I was able to shove my screwdriver completely through the auger. Then, I held the drum secure and whacked the screwdriver clockwise with a hammer and the dang auger finally twisted off! I hope this helps others!
Thank you soo much. I really needed a way to remove that part so i can properly clean it. Super happy now 🙂
Thanks for this video! Used it to get Bobby pins out under my agitator!
Huge help, thanks for the education, Ben.
thank you for showing this i seen how they take them off but not back on .. i will follow you because you seem true.
Thanks I got it. Awesome video. Once your screwdriver goes in just keep turning it clockwise it feels like it will break but it will come off
Just keep turning. If you fast forward video, you can see at the end when its off, the little pegs that hold it in place - you only have to move the housing like 2" but it can be a very difficult part to move just slightly
mine just spins freely and won't come off, it's driving me mad, barely had this damn washer for 2 years and it's broken
Thank u so much! This is the model I have and I’m having issues with it not agitating
Why do companies make it so damn hard to fix what would seem to be simple parts? Bad engineering? Trying to protect service people's jobs? It's pathetic. Great video!!! If it wasn't for people like you posting help we would be washing our clothes in a bucket!
You said it, "Trying to protect service people's jobs?". Companies rely on us buying their expensive parts and having their repair technicians replace them. Most op to purchasing a new machine. These companies are criminals taking advantage of the little guy...
I agree! GE has some of the worse engineering designs on all their appliances.
@@rick6893 don't blame the service techs, hate designs like this more than you do
Awesome explanation
Thank you for this video!
Thanks for the video!!! I had read the tech sheet on removal and had no idea wtf it was trying to say. That hole was pretty hidden. Keep the videos coming!
• Secured tub by removing washer top and clamping against a 2x4.
• Twisting with screwdriver through single hole didn’t work.
• Drilled second hole opposite to provide more leverage. Worked well.
Thanks for the tip boss, a little WD-40 up in the hole helped me out a ton too
Great video
After struggling for an hour with the screwdriver placed properly thru the auger, an oil filter wrench helped grip the auger to remove it within 2 minutes!
Our screwdriver had scraped the inside of the auger pretty significantly & wouldn't remove it alone. hope this helps!
I really needed that secret!
Thanks much for the infovideo.
Keep sharing.
Very, very helpful. For what it's worth, I think you may need to actually push the screwdriver through the inner wall of the agitator. When I removed mine, it looked like I had pierced it; it didn't look like there was a pre-existing hole that the screwdriver poked through. I may be wrong, but it was definitely hard to get the screwdriver to sink into the agitator wall and when I got the agitator removed, the inner side of the hole wasn't clean--it looked like I had jammed a screwdriver through the plastic! Nevertheless, this worked like a charm--I was able to remove the base plate to get to a piece of jewelry that had fallen beneath it. I just have an agitator with a tiny hole in it, which doesn't seem to impact the washer's functionality. Thanks very much for the video!
Happy Birthday ok
im about to stab a hole in mine there is a holeon the outside but not the inside
Is it still functional now? I'm facing a similar situation & piercing it made me worry I'd have to replace the auger.
Yes, working 100% fine.
Thanks for this info. We noticed a water leak under the machine and I was trying to figure out how to get the tub removed to see if there is a seal under it. Will removing the agitator allow me to take the tub out? Without disassembling the machine under the tub.
Thank you for the video on removing the agitator! Here’s my question, how is a piece of plastic causing issues? I would understand if it was broken but how is it messing with the washing cycle without a single sensor connected to it?
Nice info find, thanks
Thanks for the video
This was way harder than it should have been. 2 hours to muscle off a cheap plastic piece that just “clicks” on??? Thanks for the video though, got my broken agitator fixed with your video and appliance parts pro!
Thank you. I will be doing this this week lol
Thank you, I would have never figured it out on my own. Just want to clean the inside of it .( the fabric softener residue)
Calgary, Canada.
Fantastic video. This was driving me nuts trying to figure out. Thank you so much. I'm sure if GE tried they could have made getting the agitator out even more difficult than it is. What a stupid design this was. Hey GE --Just copy the older Whirlpool Direct Drive machines. I liked the comments below too. I have the identical machine to the one in your video which really helps because GE made this task so completely different over the years for their various machines.
Awesome share!!!
Bens Appliances and JUNK... my new GE (Grossly Exasperating) washer falls into the latter category! Microprocessors, diagnostic codes... I remember a time when a clothes washer ACTUALLY WASHED CLOTHES!! What a concept, GE!!
If you're unable to get the agitator off by hand I used vice grip 27ZR chain grips at the bottom of the agitator to compress it while turning, worked great - alternate solution from doing it a 2nd time, brace the bottom of the tub with your feet, no special tools required (why didn't I think of that the first time!)
Thanks for the video! Have a gearcase job in the morning and you made it significantly easier!!
I hope this helps! Its a PITA the first time, but quite easy once you've done it once or twice. Good luck on the gearshaft... Very similar to Whirlpool VMWs.
What are signs of a bad gear case?
Thank you Ben, but how do you remove the bottom spin thingy. The agitator plate I believe?
Amazing help mahalo🤙
Good video. Thank you. What was the initial problem with your washer? Mine is suddenly having a very high pitches squeal as it spins. Sounds like it's the auger tho, not a bearing. But I'll have to disassemble and find out.
It's a nightmare. Thanks for the video
Thanks for the video, I have to take my washer apart to get a lost silk pillow case that went in between the crack
If the screw driver method doesn’t work for you, use a strap wrench!
This was the ONLY way I was able to remove the agitator. ($12 at Home Depot or Walmart)
I’m a 120lb lady with no plumbing experience and I was easily able to do this without a second set of hands.
Once off, you’ll need a 7/16” socket wrench to remove the lower agitator plate if necessary for your repair.
you still need the screw driver to lock the two pieces of the auger together in order to turn it to remove it
I tried both methods without any luck!
hey man thanks for the video. Would you by happen of chance know where and how to clean the filter on this washer machine?
Any extra tips for reinstalling the agitator? I thought I did it correctly but ran a load and the agitator popped off. Just align the dots? Confused. Thank you !
Anyone who got it off is amazing. I gave up
Thanks help a bunch. ..video 1 to 10 itwas a 10
How do you remove the seal like thing under the fabric softener dispenser, I’m trying to clean my washer and I don’t know how to get it off and don’t want to risk pulling the whole thing off and breaking it. Is there a way to just pop the little seal thing out?
I have a new GE washer and the clothes constantly getting tangled so hard around the agitator it sends the washer into default mode and I’m literally almost tearing the clothes to free it from the agitator. Any input is greatly appreciated. Also, can I remove the agitator and use it without it? Tks for sharing and tia. PS. Yes the washer is level.
very helpful
Ge Washers Gods Gift to repairmen across the world
So i have this machine and i was wondering exactly how loose is this agitator suppose to be? Mine is super loose and spins crazy in spin cycle?
Is there a filter or anything on this washing machine? … I’m having an issue with mine draining and can’t figure out why.
Ben we have the same washer and we are starting to see a little flex would appear to be black rubber in our freshly washed clothes. Do you have any idea what that might be? Thanks.
works as long as the agitator isn't seized on. I just did 2 and had to use the multi tool and sledge hammer and cut and break them off. With 2 guys, one holding the tub from moving and the other trying to turn the top piece off. Ended up being too labor intensive and expensive when new agitators are not that expensive.
Yep, that's where I am at right now.
Yeah can't get mine off with the strap wrench. Where did you cut?
I'd like to see what the transmission and motors on these machines. What do they look like in action?
Thanks for this video, Ben!! GE machines are a pain 😂
IMHO, the biggest problem is just awful documentation by the tech community. Whirlpools at least have so many techs working on them its easy to spot problems. Not nearly as many videos about GEs, even though they really aren't that bad other than this agitator. Im like the only guy on YT that has semi-decent videos on them, whereas WP are dime a dozen now.
*can I remove it to make more room for bigger loads? Or can I not use it with it off*
Hey Ben saw the previous video with the diagnostic an it’s giving me the same code as yours. The machine will not go into a spin an drain an just ends up filling again any advice
My GE Profile agitator just pulls up, no screw driver needed. I used a wider belt to slide under the agitater on both sides. Then pull up quick and hard.
Awesome , thanks
We have a brand new with an agitator and it continues to fall off during the wash. Is there a way to lock it in?
My gold chain got stuck under the agitator plate, thats why im here.
Mines too😭😭😭
Hi I have the same washer in your video.. I would like to see a video on how to replace the tub... thanks
Ben, thanks, any tips for model GTWN5650F? No nib. And the hole is too small for a screwdriver
Yay ben!
Yay Brandon
Is there some way to take it apart to clean the inside of the washer.
can you please show a video of replacing the input valve on this washing machine as I can't find any and I need to replace mine!
Very good video , it help. Do you have the pert number for the agitator?
Great video. I had issues getting the agitator out though. I had to pull up then twist it clockwise. if anyone else has any trouble, try that.
Great tip!
great tip i been trying all day just by watching video and no luck but now ill try ur tip hopefully it will work.
Saved me from breaking it
Two questions.... Will this void warranty? And will this allow water to get into the middle of the agitator now?
I watched this to be able to clean the filter, am I correct there is no filter? I have the same washer ?
*can I remove it to make more room for bigger loads? Or can I not use it with it off*
We cannot get the agitator off. My husband and I have been trying for an hour. It will not budge! Any tips?
Did you find a way to get it off?
Ben , I cant find the hole underneath to take out the spinner. Maybe is only one piece with the agitator ?
Thanks!
I couldn't get the agitator out. I used a screwdriver It fit in fine like you said but I couldn't get the auger or agitator to budge. Why would that be?
Question is agitator only supposed to spin in one direction. Good video
I want to remove agitator and not put it back in. How do I do that and seal that hole.
Thanks Ben
Have same washer and it’s leaking water out from the bottom can you help me find the problem? Thanks
When putting my agitator back on, it won’t snap into place. Any ideas?
My appliance repair guys did this and it still won't come off!! Please help, I don't want to buy new washer
I followed this procedure with my five year old GTW460, lining up the dimple and the hole, punching the screwdriver through the inner plastic behind the hole and twisting the auger clockwise. That was the easy part. I was never able to get the auger off the base. The base was free wheeling or spinning freely, independent of the tub. So holding the tub was no help since the auger base spins freely, independent of the tub. I just couldn't get enough hands in there to hold the base while twisting the auger clockwise. I tried getting a screwdriver to pry up under the lower edge of the auger, but couldn't get it to budge that way either. After about 4-5 hours I gave up, with my back, shoulders, hips, and entire torso aching. I considered trying to climb up and put my feet down in the tub to hold the agitator base while twisting the auger, but at my age (78 years), I was afraid i'd not be able climb back out. That was two days ago and I'm still having problems with my back and neck, and walking without pain. I also read in some other forums that my problem is possibly the transmission. I couldn't find any reference discussing the tub spinning properly and the agitator base not locked to the tub. Calling a repairman would run $200-$300 or more, if it's only the auger and base. So, I've given up and ordered a new washing machine to replace my five year old GE machine.
I had to laugh when you mentioned climbing in and holding it with your feet! I just attempted the same and almost fell out on my head. Can just imagine calling my wife to help me from hanging off the edge off a broke down washer.
I am just starting my adventure with this process. I have read of guys cutting the whole thing off and buying a new agitator. Hope it doesn't come to that...but it might.
Glad I'm not the only one.
Ps. I'm 65 so getting too old for this stuff too. But if you did it, I can't give up.
Wish me luck!
Clockwise or counter to get it off?
HELLO MY AGITATOR MOVES LIKE IT'S LOOSE, IS THIS NORMAL? YOU CAN SHAKE IT, DON'T KNOW IF THIS NORMAL. IT ENGAGES COUNTER CLOCKWISE OK, SAME MACHINE IN VIDEO . JUST CHECKING THANKS.
How did you remove transmission?
Nice video , I have GE Washer mod WBXR2090BOWW and I have problem to take out the agitator do you know something about ?
What was the reason for you to replace it I was just going to go buy one of those and now I'm not sure if I want to buy one please explain why you changed it.
So can I completely remove the agitator? Do I have to have one?
thanks for this. the stupid service manual that came with the washer says to remove the agitator cap to expose the screws and obviously thats not what to do
Do you know how to get to the insides of this washing machine? It does not have a front PANEL but instead wraps around to the back.
You need to take the top control panel off. Remove the metal panel on the back of control tower. There are 2 more screws at the base of the plastic panel, once those are removed, inside you will see 2 more downward screws toward the back of the panel, take those out and you can then pry the top off.
can you run the machine with out the agitator????????????????