First I recomend you perform a transmission fluid flush before check any sensor. Most of the times is the filter dirty. It happened to my Chevy truck. It was just the filter plugged. That is why was the code p0741 and the truck at 45 to 55 was loosing and gaining power...
I recently got a transmission fluid change done by the dealership on my 06 Acura TL and never had any issues beforehand. Only a few weeks later did the check engine light come on and is now throwing that code. They’re suggesting I replace the transmission but that doesn’t seem right. Do you think there might be some correlation? I’m under the assumption they never did the flush properly or did not inform me on the next steps. Should I get another flush done?
My 2007 Hyundai Elantra engine light came on.. diagnostic said I need to replace my Torque converter clutch solenoid circuit electrical... thanks for your help
Hello. I have a 2005 Minicooper R53, automatic transmission. When I turn on the air conditioning, the automatic transmission goes crazy and then turns off the engine (in motion). I turn off the engine, wait a while and continue normally with the air conditioning off. Have you ever heard of a similar case? Any idea what it could be? Note: with the air conditioning off, the automatic transmission works normally. Thanks.
It sounds like an electrical problem in the vehicle. With the ac on you may be intervening with the electrical system for the trans. Possible to much draw on electrical system with ac on. Make sure you have a good battery with good connections. Check all grounds. Have a code scan done. Pay attention to any unusual noises especially when the problem happens. Check Mini Cooper forums.
My Toyota Corolla 2005 usually display the P0741 code whenever I scan it and I have already changed my Torque Converter and yet it keep showing, please what could be the pending issue? I am frustrated already
Saludos, tengo el mismo problema en un elantra año 98 me aparece el código cada vez que desconecto la batería, creo que es un convertidor reparado que le instalé. Conseguiste la solución a tu problema? No era el sensor tcc?
I bought a 04 matrix last year had check engine light, just got a diagnosis thing to check it , this is one of the codes , I put 50 k miles on it so far no problem , I’m at 256 k miles is it worth fixing or just keep trucking
I have a 1993 Pontiac Grand Prix with a 4T60E and I am having what feels to be an TCC issue. My questions is how can I disconnect the TCC so I can drive the car? I tried disconnecting B7 the TCC solenoid control wire from the ECM, and the brake switch wire going to pin A of the trasmission connector. By doing so seemed to create other symptoms Please help. Thanks
Hello, I have a question. I have a 2009 Scion Tc with 300k miles. The last time I changed the transmission oil was at 180k if I remember. However, I just recently got the code P0741. And I wanted to ask if I change the transmission oil would it slip.
I have this same issue with one of my cars but it only goes in reverse any other gear it will make this rattling sound. I hope I won’t have to replace the whole transmission
Thank you so much for the information, I have a 2009 Hyundai Sonata with the same issue, does that apply to my car as well and if so what needs to be done
I have an 07 Suburban with a 4l60e. Getting p0741. Cluster panel had a warning that said transmission fluid hot idle engine. Trans temp was at 255. Was also getting slipping at times when accelerating. Fluid looks and smells normal. Is it possible fluid and filter change could fix this or does this sound like rebuild/replacement?
Hi.i just bought a 2002 Seville that has a torque converter code..car runs n drives but lacks in power ..n tacks up then changes gears? Worth fix? Has 114k.rough cost? Thanks.Pietro
My 06 acura tl has that code i'm change the torque converter solenoid tmrw.If that doesn't fix it then it's the torque converter itself ?or transmission..
I’m dealing with the same code in my 06 TL,gears slipping,rpm’s revving when hot.I did a 3x3 drain and replaced trans filter.Still slipping .Did the TCC fix work for you?
Appreciate your video. Thank you. I realize this is along shot. Hoping you might help us please. Do you have any idea why our 1990 Honda Accord Auto Transmission does not shift into reverse sometimes and makes the funny clicking sound? Other times we start it and it shifts into reverse perfectly. We've flushed the AT and put the Honda fluid, checked the lock up and shift solenoids and cleaned the small screens. Does the Honda Lock up solenoid lock up the torque convertor clutch to make it go into reverse? Here is a video of the sound.. Thank you very much. @H9y4
Good info, I having the same code p0741 on my 04 4Runner it dies when I tried putting in gears. It idles fine in park and neutral and it die only when I tried putting in gears. It make a clacking sound when I turn off the engine. Does that mean my transmission is broken?
I've had this code come on my car (2006 Kia Sportage) two days ago, but the transmission shop says that all the mechanical components, solenoids, valve body, etc. are fine. They cleared the code and now they're not able to replicate the issue. Any ideas? You think it's a bad TCM or a wiring issue?
Hello John.. I have Ford Explorer 2010 4x4 with P0741 code since 2018 and I drove 100k miles. The A/T is still shifting fine. But (one time out of ten times) when I park the car uphill even for one hour then I start it again and put it in D, the car doesn’t move. It is like in N. It takes 5 to 10 seconds to start moving very slowly then runs fine. Can you help me? thanks!
Sounds like possible trans overhaul or replacement. Maybe try a fluid and filter change, you may get a little more life out it. We recommend dex vi fluid when doing the fluid and filter change.
@@johnandeddie Thanks for your reply During the mileage of 100k with wrench on, I have changed oil and filter twice and the wrench still on. The next few days I will change for the 3rd time.. so I am looking for solution. Thank you again
@@DaNy-th3nk P0741 was solved by adding LUCAS stop slip oil and after long milage around 13K miles. Just after pressing the accelerator hard for several times. Before that l kept pressing slowly.
What car do you have? You can learn a lot by searching for the common problems of the car. I am having a p0741 code in my gf honda civic 2007 and I found that it's likely the tcc solenoid that applies the clutch pressure. I havent changed it yet but I'm expecting that to fix it
@@thenman23 no. I think what happened was it was overfilled with oil when I bought it. After I changed the oil to the right level it hasent thrown that code. It might still be the torque converter solenoid going bad but it's only a 2600 dollar car so as long as it drives into to worried about it.
Hey john. I have a 2002 s10. ..In a 1 miles radius left driveway and come back .. Leaving my driveway when i took off it slip some and some clanking ..then few minutes later it would stall at a stop and also after restart pull in gear would slam and stall engine .. After few slams and stall starts seem to went back to normal pulling. Not drove yet tho .. Any suggestions ???
Sounds like torque convertor clutch sticking on. If it is slipping and clanking has well you most likely have internal transmission and/or torque convertor clutch failure
Can code p0741 can be solve with change transmision fluid for several times? After i done already change new filter olso check wiring and solonoid valve seems look ok.
Where can I buy the clutch? I have a P0740, I put new tcc, pwm, 3-2 downshift solenoids, ignition switch and MIL light comes on when am coming to a stop only when going 45mph or above
Actually 741 is the PCM measuring "SLIPPAGE" beyond the programmed limits. Which is usually a SEAL problem. While the accompanying code 1860, will be the "SOLENOID". But often is an "Intermittent" solenoid problem, which only gives the 741 code. Since as said,.. Is a measure of the given slippage. (approx 4%+) NIETHER OF WHICH,.. Is a Torque Converter issue. Though is part of the Direct Lockup drive system. At or above 41mph per programming specifications. Least that's what I know from my Caddy experiences. Currently a 2002 STS which I fixed with Lucas Trans Fix : ) 2700 miles without this (intermittent the last 2 yrs) code popping up. (just an experiment, after dropping a half dozen engines and transaxles) I'm sure it will be back... And a trouble code that is Far To Common. Though everything is common for Caddies 😂 😢 Best I can tell ya 🤞 EXCEPT. I would check your Grounds. And add an EXTRA Decent Gauge Ground from your Engine, to a good spot on your chassis. Preferably a spot you make yourself. Clean and well sealed. I have found TONS of issues solved by this simple addition. As these Cads seem to have Shitty Continuity and corrosion problems you will never find. But this works Great. As most sensors obviously are on your engine,.. Etc. Jus FYI ☺
We see a lot of torque convertor failure on this make and model. Could also be solenoids and/or valve body concern. Most common is torque convertor. Hope this helps.
@@johnandeddie I just bought this car a week ago for 3k the guy seemed skeptical about the transmission he has a shop should I take it to him and have him fix it for free or is that not possible at all is it (my problem now) what do you recommend me do I have pending Code p0741 torque converter clutch circuit performance/ stuck off should I start off with cleaning all the solenoids and testing them or is it something else since the problem started after running over a puddle of water 3rd and 4th gear slips please anything helps
@@musty.diesel It never hurts to ask. You can start with cleaning and clicking solenoids along with a drain and fill. It sounds more like a trans overhaul or replacement.
@@johnandeddie I cleaned the tcc solenoid the one w 6 bolts and the lock up solenoid I believe the one w 4 bolts is the a and c the one on top by the air filter hose?? It has 2 connectors and 2 bolts looks hard to get out couldn’t get my wrench in there properly, anyway the only pending code I had was p0741 it disappeared after removing the battery did solenoids and still no codes, I cleaned those two solenoids and the shifts is way harsher and the rpm’s still jump the at stopping it just jerks, my plan now is to do the tranny fluid change and add lucas, the problem started when I went over a puddle of water could it be a connector that is bad? Any recommendations will help I hope my tranny isn’t gone smh
I had my 2012 kia sportage I change the transmission 3 times and still same problem Check engine light on Transmission Difficult to go from down gear to top gear and I scanned my car I got same code So what I should do ?
@Transmissions America (John and Evan) I drive 250 miles weekly and use cruise control and the pedal interchangeably. I'll have it checked. How much is the cost/labor if it's tha t? Thanks alot! It's not the tcc solenoid?
I'm told if the p0741 code is the sensor. Which is about 40 $ it's the labor that's costly. Because of what needs to be done. To get to it. I have that code on my 2002 caddie deville. V8. Apparently this is a common problem with these cars.
Took my 2002 Oldsmobile Alero to the dealership with the same code and it would start slipping when it was shifting into 3rd gear. They said the only option was to replace the transmission ($1800). I left as the car is 17 years old and not worth $1800. Is replacing the transmission the only option to fix this issue?
$1800 is before $1000labor. I replaced mine and already having problems code: P0741 torque converter stuck after 500 miles: and again today after 1500 since swapping in a Reman 4t65E. Also, it lost 3 quarts of ATF somehow!?
Actually 741 is the PCM measuring "SLIPPAGE" beyond the programmed limits. Which is usually a SEAL problem. While the accompanying code 1860, will be the "SOLENOID". But often is an "Intermittent" solenoid problem, which only gives the 741 code. Since as said,.. Is a measure of the given slippage. (approx 4%+) NIETHER OF WHICH,.. Is a Torque Converter issue. Though is part of the Direct Lockup drive system. At or above 41mph per programming specifications. Least that's what I know from my Caddy experiences. Currently a 2002 STS which I fixed with Lucas Trans Fix : ) 2700 miles without this (intermittent the last 2 yrs) code popping up. (just an experiment, after dropping a half dozen engines and transaxles) I'm sure it will be back... And a trouble code that is Far To Common. Though everything is common for Caddies 😂 😢 Best I can tell ya 🤞
@@alexcastillo1997 This isn't a PERFECT INDICATOR. But if around 41mph at regular acceleration,.. It should feel like it Hits another gear. Which is the TCC Solenoid locking in. Remember. This IS a 4speed trans with OD. The reason why these cars can go upwards of 160 😂 And unless you are in a state as mine, (Washington),.. Which requires Emissions testing. Or this is Really Effecting DRIVABILITY. It's really nothing to worry about. GOOD LUCK 👍
Whoa Johnny, you're speaking quantum physics in Swahili! I got a kia, I'm not proud, sedona. Po741 It gets crap mpg for what the car is rated (18/24 = 11/15) even though I'm seeing 5th gear ⚙️ and doing 60-65mph cruise control set. Not worth "fixing" Can I add some crap to the transmission to help it out? Transmission honey? Aside from that, I'm shopping out a replacement vehicle.
hi could you leave me your email address I would have a problem with bmw 120d with error p0741 where it says converter exclusion clutch incorrectly disengaged. this problem is similar to yours but I find it only when I am at a constant speed ... I hear a noise like stac and then if I leave the accelerator the revs go down if I try to accelerate it becomes the same as the old American gearboxes .. could it be the converter? ?
What would cause a P0741 code on a 2007 Toyota Corolla? Because my car is running fine ... I have been driving it rough revving at high speeds pushing it before the code came on.
I have a 2006 Toyota Corolla and I had the same problem P0741. The local mechanic wanted $2500 to fix it. Way too much money. I look online and I got directed to a TH-cam video . There’s a video of a nice Asian guy who has the same code and the same car. He shows how to disconnect the wires to the transmission. He has step by step instructions on how to clean the connections with electronic spray cleaner. I went to Home Depot and bought some WD40 Electrical cleaner spray. I watched the video again to make sure on the process. I cleaned the connections and it worked. My check engine light is not on anymore. I saved the money the mechanic wanted to fix it. It’s not hard to do at all. I have had the light on for over a year. I have been driving the car all week and still no check engine light. I hope this helps.
![[#2024MAMA] BIGBANG (빅뱅) - 뱅뱅뱅 (BANG BANG BANG) + FANTASTIC BABY | Mnet 241123 방송](http://i.ytimg.com/vi/EQsYfiPR9uM/mqdefault.jpg)
Now that's a smart man who knows what he's talking bout .
First I recomend you perform a transmission fluid flush before check any sensor. Most of the times is the filter dirty. It happened to my Chevy truck. It was just the filter plugged. That is why was the code p0741 and the truck at 45 to 55 was loosing and gaining power...
if the fluid and filter have been changed recently what else do you recommend for the 45-55 power issue?
I recently got a transmission fluid change done by the dealership on my 06 Acura TL and never had any issues beforehand. Only a few weeks later did the check engine light come on and is now throwing that code. They’re suggesting I replace the transmission but that doesn’t seem right.
Do you think there might be some correlation? I’m under the assumption they never did the flush properly or did not inform me on the next steps. Should I get another flush done?
Nice video straight to the point...not trying to be funny by constantly trying to tell jokes. Just informational video.
LMAO at "trans guy"😂😂
Awesome video tho. Thanks
Wow.. best explanation ever
Glad it was helpful!
How do you test the tcc solenoids(transmission removed)? What setting should the on meter be at and what reading should I get? Thanks in advance.
My 2007 Hyundai Elantra engine light came on.. diagnostic said I need to replace my Torque converter clutch solenoid circuit electrical... thanks for your help
Hello. I have a 2005 Minicooper R53, automatic transmission. When I turn on the air conditioning, the automatic transmission goes crazy and then turns off the engine (in motion). I turn off the engine, wait a while and continue normally with the air conditioning off. Have you ever heard of a similar case? Any idea what it could be? Note: with the air conditioning off, the automatic transmission works normally. Thanks.
It sounds like an electrical problem in the vehicle. With the ac on you may be intervening with the electrical system for the trans. Possible to much draw on electrical system with ac on.
Make sure you have a good battery with good connections. Check all grounds. Have a code scan done. Pay attention to any unusual noises especially when the problem happens. Check Mini Cooper forums.
@@johnandeddie Thanks!
My Toyota Corolla 2005 usually display the P0741 code whenever I scan it and I have already changed my Torque Converter and yet it keep showing, please what could be the pending issue? I am frustrated already
Saludos, tengo el mismo problema en un elantra año 98 me aparece el código cada vez que desconecto la batería, creo que es un convertidor reparado que le instalé. Conseguiste la solución a tu problema? No era el sensor tcc?
Mines reading the same. Torque converter clutch solenoid. I found a really good video on replacing them. Actually easy.
I bought a 04 matrix last year had check engine light, just got a diagnosis thing to check it , this is one of the codes , I put 50 k miles on it so far no problem , I’m at 256 k miles is it worth fixing or just keep trucking
If it's shifting properly it means you are probably going to lose a small % mpg at highway speed and that's it... Transmission will run hotter too
How much is to replace a Torque converter on a Camry ?
I have a 1993 Pontiac Grand Prix with a 4T60E and I am having what feels to be an TCC issue. My questions is how can I disconnect the TCC so I can drive the car? I tried disconnecting B7 the TCC solenoid control wire from the ECM, and the brake switch wire going to pin A of the trasmission connector. By doing so seemed to create other symptoms Please help. Thanks
Could this be "fixed" by adding lucas antislip?
You can try it, mostly needs internal repairs
Hello, I have a question. I have a 2009 Scion Tc with 300k miles. The last time I changed the transmission oil was at 180k if I remember. However, I just recently got the code P0741. And I wanted to ask if I change the transmission oil would it slip.
I tried changing the transmission fluid, but the code came back 3 days later
I have this same issue with one of my cars but it only goes in reverse any other gear it will make this rattling sound. I hope I won’t have to replace the whole transmission
Damn did you have to
I think is better to change it the whole transmission because I think you half to take the whole transmission off
Thank you so much for the information, I have a 2009 Hyundai Sonata with the same issue, does that apply to my car as well and if so what needs to be done
Did you fix it and what was it? I have 2009 hyundai sonata too
With the same problem
I have an 07 Suburban with a 4l60e. Getting p0741. Cluster panel had a warning that said transmission fluid hot idle engine. Trans temp was at 255. Was also getting slipping at times when accelerating. Fluid looks and smells normal. Is it possible fluid and filter change could fix this or does this sound like rebuild/replacement?
What ended up being the issue having similar problems.
Did they check the solenoids?
Hi.i just bought a 2002 Seville that has a torque converter code..car runs n drives but lacks in power ..n tacks up then changes gears? Worth fix? Has 114k.rough cost? Thanks.Pietro
prices vary depending on location, good mileage, worth repairing
My 06 acura tl has that code i'm change the torque converter solenoid tmrw.If that doesn't fix it then it's the torque converter itself ?or transmission..
I’m dealing with the same code in my 06 TL,gears slipping,rpm’s revving when hot.I did a 3x3 drain and replaced trans filter.Still slipping .Did the TCC fix work for you?
Appreciate your video. Thank you. I realize this is along shot. Hoping you might help us please. Do you have any idea why our 1990 Honda Accord Auto Transmission does not shift into reverse sometimes and makes the funny clicking sound? Other times we start it and it shifts into reverse perfectly. We've flushed the AT and put the Honda fluid, checked the lock up and shift solenoids and cleaned the small screens. Does the Honda Lock up solenoid lock up the torque convertor clutch to make it go into reverse? Here is a video of the sound.. Thank you very much. @H9y4
I also have a P0741 code on my '08 merz C300, how much would you think the cost to repair it?
Thank you or your comment. Prices vary depending on your area.
How much was it
I have a 2007 Escape. TCC wont turn on in the OBD2. No code. Car wont drive when warm. Sucks. Gonna try and fix 😬
Good info, I having the same code p0741 on my 04 4Runner it dies when I tried putting in gears. It idles fine in park and neutral and it die only when I tried putting in gears. It make a clacking sound when I turn off the engine. Does that mean my transmission is broken?
Very possible. Sounds like torque convertor clutch stuck on.
@@johnandeddie I have 2018 Honda pilot dealer saying type c solenoid stuck off bad but it still ride good but computer say " transmissions failure..
Hello, I have a Isuzu trooper 1994 3.2 v6 I’m getting a transmission code #26 what is a code 26 ?
I have a 2006 honda odyssey. So replacing the "donut" should solve the problem, yes? Thanks.
So did you sell it to the junk yard yet..or are you still trying to sell it..
Nah replace the solenoid
I've had this code come on my car (2006 Kia Sportage) two days ago, but the transmission shop says that all the mechanical components, solenoids, valve body, etc. are fine. They cleared the code and now they're not able to replicate the issue. Any ideas? You think it's a bad TCM or a wiring issue?
Try servicing trans with additive
Very informative man A++
Hello John.. I have Ford Explorer 2010 4x4 with P0741 code since 2018 and I drove 100k miles. The A/T is still shifting fine. But (one time out of ten times) when I park the car uphill even for one hour then I start it again and put it in D, the car doesn’t move. It is like in N. It takes 5 to 10 seconds to start moving very slowly then runs fine. Can you help me? thanks!
Sounds like possible trans overhaul or replacement. Maybe try a fluid and filter change, you may get a little more life out it. We recommend dex vi fluid when doing the fluid and filter change.
@@johnandeddie
Thanks for your reply
During the mileage of 100k with wrench on, I have changed oil and filter twice and the wrench still on. The next few days I will change for the 3rd time.. so I am looking for solution. Thank you again
Do you solved it ?
@@DaNy-th3nk
P0741 was solved by adding LUCAS stop slip oil and after long milage around 13K miles. Just after pressing the accelerator hard for several times. Before that l kept pressing slowly.
John, on 2005 Chevy Astro, could this code indicate just a bad TCC solenoid?
I’m asking the same thing
Very helpful.
I have the same code p0741 do I have to change the torque converter??
What car do you have? You can learn a lot by searching for the common problems of the car. I am having a p0741 code in my gf honda civic 2007 and I found that it's likely the tcc solenoid that applies the clutch pressure. I havent changed it yet but I'm expecting that to fix it
@@mikealll600 well did it?
@@thenman23 no. I think what happened was it was overfilled with oil when I bought it. After I changed the oil to the right level it hasent thrown that code. It might still be the torque converter solenoid going bad but it's only a 2600 dollar car so as long as it drives into to worried about it.
I have a 2002 Cadillac Eldorado collectors series and that code popped up can you give me a ballpark figure on the repair
Hey john. I have a 2002 s10. ..In a 1 miles radius left driveway and come back .. Leaving my driveway when i took off it slip some and some clanking ..then few minutes later it would stall at a stop and also after restart pull in gear would slam and stall engine .. After few slams and stall starts seem to went back to normal pulling. Not drove yet tho .. Any suggestions ???
Sounds like torque convertor clutch sticking on. If it is slipping and clanking has well you most likely have internal transmission and/or torque convertor clutch failure
what’s the price you offer for that service
prices vary
Can code p0741 can be solve with change transmision fluid for several times? After i done already change new filter olso check wiring and solonoid valve seems look ok.
possibly, try adding Lube Guard instant shudder fixx in 2oz red tube
Good morning my friend i have a problem with the solenoid valve and the code type is p0741 question what is to do? Accept my greetings
Where can I buy the clutch? I have a P0740, I put new tcc, pwm, 3-2 downshift solenoids, ignition switch and MIL light comes on when am coming to a stop only when going 45mph or above
Actually 741 is the PCM measuring "SLIPPAGE" beyond the programmed limits.
Which is usually a SEAL problem.
While the accompanying code 1860, will be the "SOLENOID".
But often is an "Intermittent" solenoid problem, which only gives the 741 code. Since as said,.. Is a measure of the given slippage. (approx 4%+)
NIETHER OF WHICH,.. Is a Torque Converter issue.
Though is part of the Direct Lockup drive system. At or above 41mph per programming specifications.
Least that's what I know from my Caddy experiences.
Currently a 2002 STS which I fixed with Lucas Trans Fix : )
2700 miles without this (intermittent the last 2 yrs) code popping up.
(just an experiment, after dropping a half dozen engines and transaxles)
I'm sure it will be back...
And a trouble code that is Far To Common. Though everything is common for Caddies 😂 😢
Best I can tell ya 🤞
EXCEPT.
I would check your Grounds.
And add an EXTRA Decent Gauge Ground from your Engine, to a good spot on your chassis. Preferably a spot you make yourself. Clean and well sealed.
I have found TONS of issues solved by this simple addition. As these Cads seem to have Shitty Continuity and corrosion problems you will never find. But this works Great. As most sensors obviously are on your engine,.. Etc.
Jus FYI ☺
What about a 05 Honda Accord 3.0 v6
We see a lot of torque convertor failure on this make and model. Could also be solenoids and/or valve body concern. Most common is torque convertor. Hope this helps.
@@johnandeddie I just bought this car a week ago for 3k the guy seemed skeptical about the transmission he has a shop should I take it to him and have him fix it for free or is that not possible at all is it (my problem now) what do you recommend me do I have pending Code p0741 torque converter clutch circuit performance/ stuck off should I start off with cleaning all the solenoids and testing them or is it something else since the problem started after running over a puddle of water 3rd and 4th gear slips please anything helps
@@musty.diesel It never hurts to ask. You can start with cleaning and clicking solenoids along with a drain and fill. It sounds more like a trans overhaul or replacement.
@@johnandeddie I cleaned the tcc solenoid the one w 6 bolts and the lock up solenoid I believe the one w 4 bolts is the a and c the one on top by the air filter hose?? It has 2 connectors and 2 bolts looks hard to get out couldn’t get my wrench in there properly, anyway the only pending code I had was p0741 it disappeared after removing the battery did solenoids and still no codes, I cleaned those two solenoids and the shifts is way harsher and the rpm’s still jump the at stopping it just jerks, my plan now is to do the tranny fluid change and add lucas, the problem started when I went over a puddle of water could it be a connector that is bad? Any recommendations will help I hope my tranny isn’t gone smh
How much is this job.
Prices vary depending on the area
I have an 04 Acura tl same code where is your shop located
Been dealing with that code and man is a pain in the ass. Car runs and drives good. But once i put it on the freeway damn code apears everytime
@@candula87 IMHO drive it till it dies. I spent a few G trying to solve this on a caddy and it still imploded in 48 months.
great info.....
Thanks for watching!
I had my 2012 kia sportage I change the transmission 3 times and still same problem
Check engine light on
Transmission Difficult to go from down gear to top gear
and I scanned my car I got same code
So what I should do ?
Very well
I have a 08 pontiac grand prix and the code P0741 come on. Why?
Most likely cause is convertor clutch slippage
@Transmissions America (John and Evan) I drive 250 miles weekly and use cruise control and the pedal interchangeably. I'll have it checked. How much is the cost/labor if it's tha t? Thanks alot! It's not the tcc solenoid?
Hi I have bmw e46 03'. Remplace 2 transmission same code p0741 I bought a one more and same code come back help
I have 2008 corolla. Most times once i reach 100km/h I get the code p0741.
In my case what's the solution?
a new transmission
I'm told if the p0741 code is the sensor. Which is about 40 $ it's the labor that's costly. Because of what needs to be done. To get to it. I have that code on my 2002 caddie deville. V8. Apparently this is a common problem with these cars.
That's the same as my car and, this is why I'm here. What did it end up costing you to fix?
@@c.r.edmister5223 sold the car !!
@@CCW-wg8ds sad ending
If a Cadillac Deville is a luxury car why does this happen I only have 170000 miles on my car
@@diannbajewicz8952 that's what mine had a common thing with these cars
Took my 2002 Oldsmobile Alero to the dealership with the same code and it would start slipping when it was shifting into 3rd gear. They said the only option was to replace the transmission ($1800). I left as the car is 17 years old and not worth $1800. Is replacing the transmission the only option to fix this issue?
$1800 is before $1000labor.
I replaced mine and already having problems code: P0741 torque converter stuck after 500 miles: and again today after 1500 since swapping in a Reman 4t65E.
Also, it lost 3 quarts of ATF somehow!?
If the code show on Toyota cars it means replace torque converter.
My 2013 malibu eco has this code after fluid flush.
Any suggestions?
Possible solenoid clogged up and/or something could have stuck in valve body.
We use dex vi fluid with a Lube Guard platinum additive
nice stylus pro, it looks well worn.
Damn that will cost more than my 2004 is worth. Uhg
Lmao john the trans guy
could we just drive with no torque converter lock?
Not recommended
That's a accident waiting to happen on small streets
I put a new torque converter and the same code came on
Actually 741 is the PCM measuring "SLIPPAGE" beyond the programmed limits.
Which is usually a SEAL problem.
While the accompanying code 1860, will be the "SOLENOID".
But often is an "Intermittent" solenoid problem, which only gives the 741 code. Since as said,.. Is a measure of the given slippage. (approx 4%+)
NIETHER OF WHICH,.. Is a Torque Converter issue.
Though is part of the Direct Lockup drive system. At or above 41mph per programming specifications.
Least that's what I know from my Caddy experiences.
Currently a 2002 STS which I fixed with Lucas Trans Fix : )
2700 miles without this (intermittent the last 2 yrs) code popping up.
(just an experiment, after dropping a half dozen engines and transaxles)
I'm sure it will be back...
And a trouble code that is Far To Common. Though everything is common for Caddies 😂 😢
Best I can tell ya 🤞
TANGLDWEB thank you
@@alexcastillo1997
This isn't a PERFECT INDICATOR.
But if around 41mph at regular acceleration,.. It should feel like it Hits another gear. Which is the TCC Solenoid locking in. Remember. This IS a 4speed trans with OD.
The reason why these cars can go upwards of 160 😂
And unless you are in a state as mine, (Washington),.. Which requires Emissions testing. Or this is Really Effecting DRIVABILITY.
It's really nothing to worry about.
GOOD LUCK 👍
@@alexcastillo1997
...oh,.. That'll be $1100.
I accept PAYPAL 😂
Drive sprocket support 8681071 p/n wears out and takes out the TCC seals, very common problem with the 4t80.
Whoa Johnny, you're speaking quantum physics in Swahili!
I got a kia, I'm not proud, sedona.
Po741
It gets crap mpg for what the car is rated (18/24 = 11/15) even though I'm seeing 5th gear ⚙️ and doing 60-65mph cruise control set.
Not worth "fixing"
Can I add some crap to the transmission to help it out?
Transmission honey?
Aside from that, I'm shopping out a replacement vehicle.
hi could you leave me your email address I would have a problem with bmw 120d with error p0741 where it says converter exclusion clutch incorrectly disengaged. this problem is similar to yours but I find it only when I am at a constant speed ... I hear a noise like stac and then if I leave the accelerator the revs go down if I try to accelerate it becomes the same as the old American gearboxes .. could it be the converter? ?
That is what happened to my Cadillac 2004 nobody wants to buy my car because of that
I think buying another car is a better option
What happens when your 4l60e torque converter stays locked
You get 7 neutrals
What would cause a P0741 code on a 2007 Toyota Corolla? Because my car is running fine ... I have been driving it rough revving at high speeds pushing it before the code came on.
Possible internal failure
th-cam.com/video/W7LG2tDCgF8/w-d-xo.html
I have a 2006 Toyota Corolla and I had the same problem P0741. The local mechanic wanted $2500 to fix it. Way too much money. I look online and I got directed to a TH-cam video . There’s a video of a nice Asian guy who has the same code and the same car. He shows how to disconnect the wires to the transmission. He has step by step instructions on how to clean the connections with electronic spray cleaner. I went to Home Depot and bought some WD40 Electrical cleaner spray. I watched the video again to make sure on the process. I cleaned the connections and it worked. My check engine light is not on anymore. I saved the money the mechanic wanted to fix it. It’s not hard to do at all. I have had the light on for over a year. I have been driving the car all week and still no check engine light. I hope this helps.
@@Windows121165 I tried this method as well and that connection is such a pain to pull off but i did and nope it didn't help me in my case ...