2015 Ford escape 1.6 2wd how remplece front bering and hub. Como remplazar balero delanteo y maza.
ฝัง
- เผยแพร่เมื่อ 8 ก.ย. 2024
- How remove and replace a front bearing on a ford escape without losing alignment in the same vehicle. Como se remplaza un balero delantero y una maza en el mismo carro sin perder la alineacion en una camioneta Ford 2015
![[Watch Party] RoV Pro League 2024 Winter | ( Bacon Time Vs PSG )](http://i.ytimg.com/vi/zM25REvnJW4/mqdefault.jpg)
![[LIVE] : ONE ลุมพินี 78 | คู่เอก "ปกรณ์ vs ฟาบิโอ"](http://i.ytimg.com/vi/LSOmgl0Th2c/mqdefault.jpg)
Well done very helpful
Thanks
Thank you. I am going to attempt this repair ASAP myself.
Saved me from replacing the whole part.
Any time good look
That poor brake caliper hose is the first thing I noticed when the video started.
It’s an excellent step by step video. Absolutely saved and liked. 👍🏽
Muchas gracias por su ayuda mi amigo, DIOS lo bendiga siempre 🙏🏽.
Gracias igualmente
Appreciate your video, had useful information I couldn't find in any other videos. Now if I can only get the hub off using my slide hammer lol. Been sliding that thing for an hour and it's not budging. Might have to use heat and some wedges with it. Thanks again.
Thanks
Appreciate the video, I did both sides of an Escape at 130kmi.
The only improvement I suggest is to use a dremel to cut a small notch in the old bearing race on the hub(it doesn't even have to be completely through), then, using a chisel and hammer, smack the race a few times until it breaks free. That task shouldn't take more than about 5 minutes and it will save you >70 dollars because you can reuse the hubs.
Hardest part for me was using the slide hammer, >45 minutes messing with that and I had to use some wedges hammered in between the hub and knuckle to finally break it free.
I will take your information into thank you
I was wondering if the hubs could be reused. Good tip. Thanks!
This is huge. Thank you for typing this out brother. Respect.
I'm going to have to do this soon and I thank you VERY much!!
Any time
The caliper!…
Thank you very helpful
Thanks for watching this video. Any time you have any questions please let me know.
Which Milwaukee impact you use ?
Wrenches
Milwaukee
M18 FUEL ONE-KEY 18V Lithium-Ion Brushless Cordless 1/2 in. Impact Wrench with Friction Ring
Que tal Olvera G. Exelente contenido 👍🏻, que sucede si solo se cambia el balero y la segunda pieza se coloca la misma que tenía el carro.. presenta algún ruido ?..
O es necesario cambiar ambas piezas .?
Gracias .. saludos
Jose flores si la masa tiene desgaste es mejor cambiarla ya que tendrá juego y u balero no durara mucho tiempo por eso yo siempre cambio ambas saludos y gracias por tu comentario.
Another method to remove the inner race from the hub is to heat the ring with a torch, it will expand and slide off easily
Esa herramienta para sacar el balero la rentan ? En auto zone ? Buen vídeo
Saludos me parece q en solo algunos o raiies, la que yo tengo es otc 6575. Pero si esta puedes comprarla en harbor freight MADDOX
Front Wheel Drive Bearing Remover and Installer Kit, 21 Piece.
Excelente video. Donde puedo comprar la herramienta para sacar el bearing.
Gracias amigo 🙏🏽
Saludos Jesus en usa algunos o railes los tienen en renta pero si no en amazon otc 6575.
Oem tools27213 o en harbor freight MADDOX
Front Wheel Drive Bearing Remover and Installer Kit, 21 Piece.
Como hizo para meter el ring de metal que asegura después de haber metido el bearing ? El que va alreded del speed sensor. No logro meterlo 😢
Lo puede acer con unas pinzas de punta o con unos desarmadores planos solo tengas mucho cuidado ya que se puede chispar y podria pagarle en un ojos asi que use lentes de protecion. Intense meter un lado donde empieza el seguro y con desarmador plano aga precion para empugarlo a la pocion. Si eso no funciona recomiendo consign una pinzas de seguros
@@olveragaragegracias
where did you get that tool i need one so bad such a life saver lol
Front otc 6575 hub grappler puller
@@olveragarage thank you life saver
Just letting the brake caliper hang on the brake line huh?
Mechanical 101.... don't EVER do that
been doing it for 40+ years it wont hurt a thing.
It doesn't hurt anything if the caliper line isn't visibly messed up.
@@toddbob55 EXACTLY. Tell em'.
That's ok. If good enough is good enough for you guys, that's fine.
There is a reason I get to work at the level I do... subtle details such as this.
Always strive for better and never "good enough."