Благодарю. Красиво, но немного неудобно. В "ручном" режиме, желательна регулируемая по углу наклона к плоскости инструмента рукоять, закреплённая на трубе большего сечения. Подобно плоскому напильнику, но за счёт регулируемой рукояти более удобно. Рукоять может быть зафиксирована как над полотном "наждачки" ( можно оградить руку на подобие эфеса), так и сбоку, или сбоку и снизу, г- образно, как удобнее. Рукоять избавит от неприятных скачков инструмента при "наезде" на "задир" или кромку. В стационарном режиме, опорную для обрабатываемой детали плоскость, можно,при желании, использовать в качестве опоры для другой плоскости (можно с регулируемым наклоном), смещенной в область плоскости опорной трубы.
This has to be one of the coolest ideas I've seen on TH-cam. Great video . The only I would do is to add a flat washer to the screw the is located on the square tubing slot. It will prevent future warping of the metal along the slot. It also will distribute the weight evenly over the surface. 2 THUMBS UP 👍👍.
Здравствуйте было бы правильно верхнюю часть из профтрубы надеть другую профтрубу опора подшипника подошла бы и лента скользила по ровной поверхности а длину подогнать с минимальным зазором.удачи в дальнейших разработках.
what type of cables did you use and where did you buy them from ,i need to know before i order from banggood. nice build love it will be trying my hand at this one later
Estou falando com voce doBRASIL gostaria de saber se voce fas esta pesa para vender gostei muito hoge estou trbalhando de pintura e esta feramenta seria muito utio para mim se posiveo me responda a moeda corente e realfasa a confersao para mim e eu ficaria contente aguardo jairo meu nome
WARNING! Do not try this at home without a lathe. There is no way to get the absolute center of that round bar and those discs with any accuracy by eye. This guy's videos are VERY misleading. I also suspect he's using a chop saw or horizontal band saw to make the linear cuts too, substituting those parts for the hand-cut parts off camera. This guy has some good ideas but his manufacturing techniques of the devices are a bit of a fraud.
David. Ciertamente este no es un trabajo para principiantes, se debe tener cuidado en la construcción y alineación de las poleas, ya que si no se alinean correctamente, la banda tiende a salir de su lugar. El video no lo muestra, pero seguro tuvo que hacer correcciones hasta encontrar el punto adecuado de alineación.
That’s a very interesting/peculiar TIG welding technique you have there. Seems to work for spot welds but how’s that tungsten holding up?
That is brilliant 😎👍💵🤜🤛💥
Excelente!
Gracias por el vídeo
Saludos desde la Ciudad de México
Muy bueno; estas cosas ingeniosas se agradecen y se dan las gracias por mostrarlas felicitaciones desde chile
Thank you so much!
One of the best belt grinder video I saw ever. Bravo, great job. You have my attention
Thank you so much!
God gave you so much talent and you share it with us thanks man
Thank you so much! I always improve my skills to make more videos and share with you all!
@@KwandoTechnic by the way what type of welder do you used I mean the thing you use to weld what is it called
This is my welder, you can see detail and order at here: bit.ly/30T55h0
SIMPAL BUT VERY BEST IDEA +VERY USEFUL 👍👍👍
Hello
Быстро свою ошибку исправил молодец 😊
So simple to make and nice shown video! Thank you for sharing!
Thank you so much!
Projeto & conclusivo genial parabéns, excelente 👍👏
Thank you so much!
Τέλεια η κατασκευή του τροχού να είναι τριβειο με γυαλοχαρτο 1.000 μπράβο πάντως.
Excelente un genio, felicito amigo.
Thank you!
Great idea thanks a lot😁👍
You are welcome!
Is this soldering pen of the MIG type? Do you use any kind of gas? Congratulations on the videos and creativity !!!!
Thank you. I used TIG welder and argon air.
Благодарю. Красиво, но немного неудобно. В "ручном" режиме, желательна регулируемая по углу наклона к плоскости инструмента рукоять, закреплённая на трубе большего сечения. Подобно плоскому напильнику, но за счёт регулируемой рукояти более удобно. Рукоять может быть зафиксирована как над полотном "наждачки" ( можно оградить руку на подобие эфеса), так и сбоку, или сбоку и снизу, г- образно, как удобнее. Рукоять избавит от неприятных скачков инструмента при "наезде" на "задир" или кромку. В стационарном режиме, опорную для обрабатываемой детали плоскость, можно,при желании, использовать в качестве опоры для другой плоскости (можно с регулируемым наклоном), смещенной в область плоскости опорной трубы.
Many thanks for your advise. Everything issues that you mention, I though about them.
Great job....
Thank you!
Great project. What kind of welder is that? Looks super easy to use.
It's TIG welder. You can see more detail at here: bit.ly/30T55h0
Elinize emeyinize sağlik ustat harika olmüş
Thanks!
great job!
Many thanks!
@@KwandoTechnic Please"
О Молодес , отличная работа.эолотая рука
Thank you!
Muito bom mesmo eu gostei bem explicado
Yes, always like that.
Good job..👍👍👍
Job could be done by emery paper with grinder no need for this device , but i like your craftsmanship
Thank you so much!
One Best of this type! I love TIG
Excuse me, I was wrong in the question, is the pen a TIG type? thanks
GOOD JOB
Thanks!
This has to be one of the coolest ideas I've seen on TH-cam. Great video . The only I would do is to add a flat washer to the screw the is located on the square tubing slot. It will prevent future warping of the metal along the slot. It also will distribute the weight evenly over the surface. 2 THUMBS UP 👍👍.
Many thanks for your suggestions!
The axle on small bearings is erroneously tacked by welding, these bearings burned out for me and I got a problem, this assembly must be collapsible.
Nice job Kwando. I would suggest investing in a horizontal band saw. You would have much more accurate cuts.
Many thanks for your suggestion!
o seu trabalho e magnifico eu não perco um vídeo seu nota 10 em tudo que vc faz
Thanks!
ชอบไอเดียมากครับ ช
Thank you so much!
Hello please can you tell us what kind of welding equipment you are using. . Thank you
I use TIG welder as: bit.ly/30T55h0
Здравствуйте было бы правильно верхнюю часть из профтрубы надеть другую профтрубу опора подшипника подошла бы и лента скользила по ровной поверхности а длину подогнать с минимальным зазором.удачи в дальнейших разработках.
Отлично !
Thank you!
Шлифмашина и гриндер,2 в 1,интересная идея!
Many thanks!
최고다👍👍👍😀
Hello friend what was the tool you used to make the weld?
I use TIG welder as: bit.ly/30T55h0
Hello,,,,,Please,give me information about the welding machine you use
04:40 المسمار في ميلان..ماينفع..لازم مخرطة
почему аргон, действительно дешевле электродов. ? работа хорошая 5+
what type of cables did you use and where did you buy them from ,i need to know before i order from banggood. nice build love it will be trying my hand at this one later
How do you stop it from going off track
Hi.... Is it for sell ?? If so, how much would it be ??
Sorry, I made it for myself.
👍👍👍👍👍
Estou falando com voce doBRASIL gostaria de saber se voce fas esta pesa para vender gostei muito hoge estou trbalhando de pintura e esta feramenta seria muito utio para mim se posiveo me responda a moeda corente e realfasa a confersao para mim e eu ficaria contente aguardo jairo meu nome
Sorry, please make me more clear what's your concern?
👍👍💪💪
But I still like it I got to make this toy
👏👍🏾👍🏾
Nice idea. :)
However, it's a bit to massive for my liking, but that's just me. TIG welding outside isn't really such a good idea... ;)
Many thanks for your opinion!
Que tipo de solda e essa
This is my welder's information: bit.ly/30T55h0
Лайк за идею
What kind of welding machine?
This is my welder, you can see detail and order at here: bit.ly/30T55h0
If you have to ask what type of welder you shouldn't be thinking of making anything like this
Congratulation
Лайк.
Зебс👍🏻
KL gitu mah udah aja beli amplas 5000 langsung pasang jadi ampelad.maaf
Чё за сварка ?
About my welder, please see more detail at here: bit.ly/30T55h0
like y subcrito, spain
Many thanks!
Что за сварочный аппарат, не знаю почему???
Незнаю?
This is my welder, you can see detail at here: bit.ly/30T55h0
Ок
This is cool New friend Ruthie
Thank you so much!
WARNING! Do not try this at home without a lathe. There is no way to get the absolute center of that round bar and those discs with any accuracy by eye. This guy's videos are VERY misleading. I also suspect he's using a chop saw or horizontal band saw to make the linear cuts too, substituting those parts for the hand-cut parts off camera. This guy has some good ideas but his manufacturing techniques of the devices are a bit of a fraud.
David. Ciertamente este no es un trabajo para principiantes, se debe tener cuidado en la construcción y alineación de las poleas, ya que si no se alinean correctamente, la banda tiende a salir de su lugar. El video no lo muestra, pero seguro tuvo que hacer correcciones hasta encontrar el punto adecuado de alineación.
Бланк
تفووووووووووو على من اعد هذا الفيديو
Hello
⭐⭐⭐⭐⭐ +⭐👍
good Idia but not work