If the consumption is below 2 amps, you can use an insulating cover. It is better to use heat sharing. If the current draw is higher than 2 amps, it is necessary to use a heatsink on the main chip.
No, you must use this module to safely charge the battery with charge and discharge protection. Watch this video: th-cam.com/video/Z9_lvZtLHgA/w-d-xo.html
@@newtecproTHIS VIDEO DOESN'T HELP ME IS FOR 5 VOLT.. NEED SOMETHING FOR CHARGE 12 VOLT BATTERY FROM A SOLAR PANEL THAT DELIVERY 18 VOLT IN THE OUTPUT
Bro i have a xl4016 e1 it give the same output as input and it is not adjusting the voltage even after turning the trimmer what is the problem? Please do reply
Is the potentiometer healthy? Make sure the multitrain is healthy. Also remember that: If you use a step-down module, the output voltage is always lower than the input. If you use a step-up module, the output voltage is always higher than the input.
@@saicharanrrao6027 It is possible that the potentiometer has a problem. You can replace the same potentiometer or replace it with a suitable volume and test. If it doesn't work, you need to replace the reducer module.
If you have used a battery (eg 12V DC or 9V) in your solar system, yes. Get 9V DC from the battery output and convert it to 5V using the voltage reducer module.
No, I don't have this. But this electronic board is available in ready and modular form in the market and I will put the link to buy it in the description
Hello. Because the output voltage is variable, it cannot be set to 24 volts without a multimeter. Can you help someone with a multimeter for a few minutes? It is enough to set the output to 24V once
Thanks. Helped me succeed in my first try of using a buck converter.
Thank you for your encouraging message. I hope our next videos will be useful for you
Pm me can you to install do solar panel of charger _
Does this have the range to step down a 24v source to 3-5v?
Yes, it is suitable. The input voltage can be from 3 to 36 volts and the output can be set from 1.5 to 30.
@@newtecpro Thanks!
Pm me can you to install do solar panel of charger _
Nice, voltage converters are very cool.
Yes, they are perfect. For example, it can reactivate an unusable power supply.
Pm me can you to install do solar panel of charger _
Can i wrap it with insulation tape? Just to stabilize a single 12v minifan 0.12A outdoor
If the consumption is below 2 amps, you can use an insulating cover. It is better to use heat sharing.
If the current draw is higher than 2 amps, it is necessary to use a heatsink on the main chip.
Pm me can you to install do solar panel of charger _
Is there any module where you can swap + and - because of reverse in cars?
If possible, express your question more clearly. What do you mean by replacing - and +?
TELL ME.. THIS DEVICE PREVENTS OVERCHARGING OF THE BATTERY..?
No, you must use this module to safely charge the battery with charge and discharge protection. Watch this video: th-cam.com/video/Z9_lvZtLHgA/w-d-xo.html
@@newtecproTHIS VIDEO DOESN'T HELP ME IS FOR 5 VOLT.. NEED SOMETHING FOR CHARGE 12 VOLT BATTERY FROM A SOLAR PANEL THAT DELIVERY 18 VOLT IN THE OUTPUT
@@miguellovino7679 Soon I will post a new video on the channel for 12 volt batteries
Bro i have a xl4016 e1 it give the same output as input and it is not adjusting the voltage even after turning the trimmer what is the problem? Please do reply
Is the potentiometer healthy? Make sure the multitrain is healthy. Also remember that:
If you use a step-down module, the output voltage is always lower than the input.
If you use a step-up module, the output voltage is always higher than the input.
@@newtecpro it's a step down but it's giving the output same as input
Is it a potentiometer problem?
@@saicharanrrao6027 It is possible that the potentiometer has a problem. You can replace the same potentiometer or replace it with a suitable volume and test. If it doesn't work, you need to replace the reducer module.
Can I ask...can I use that in my 9v solar panel... thank you for the tutorial and the review of the converter...I hope I can do it the right way
If you have used a battery (eg 12V DC or 9V) in your solar system, yes. Get 9V DC from the battery output and convert it to 5V using the voltage reducer module.
@@newtecpro Can I wire the output of a buck converter directly to a usb, set it to 5volts and charge my phone with it?(Or 5.5 volts whatevers)
Pm me can you to install do solar panel of charger _
Did you all apply solder to the input and output terminals before getting started?
Yes, this is a better way to connect the wires. Faster and stronger soldering
Pm me can you to install do solar panel of charger _
what wire did you use?
Because the maximum amperage of the voltage converter is 2.5A, you can use a wire with a thickness of 0.75mm.
would you happen to have a schematic of the circuit you made?
No, I don't have this. But this electronic board is available in ready and modular form in the market and I will put the link to buy it in the description
very nice
Thanks
Pm me can you to install do solar panel of charger _
Can I use it on my ESP32 Dev Board? with AC/DC Adaptor, which the AC is around (100V-240V)
and DC is (9V 2A)
You have a 9V 2A adapter is that correct? What is the voltage you need?
@@newtecpro Yes, but I do not know what voltage is needed to ESP32 DEV BOARD. Sorry, I am newbie
@@playdoms-v5v esp32 boards are similar to arduino so it'll prob use a 5v in.
you can also get Ac-Dc & Dc-Ac converters ..
Hi, is something wrong with my LM when the colour of diode is red, not blue?
Hi, no problem. I'm currently using an old module which is on. Its LED is red
Pm me can you to install do solar panel of charger _
Hi, is this suitable for audio devices? I plan on making a multiple power supply for guitar pedals and a single 24v power supply
Yes, you can use it, but this final model must have an output of 2.5 amps. If you cool it
Pm me can you to install do solar panel of charger _
Without load form o/p,preset not adjusted. But LED connect of o/p then preset is working.module is ok OR defective.please teil me.
What input voltage have you connected to this module? What voltage do you get at the output with the multimeter?
Pm me can you to install do solar panel of charger _
Does it step down current?
No, this model cannot reduce the current. Soon we will post a video of the new model that has the ability to reduce current.
Pm me can you to install do solar panel of charger _
did it come from the factory set to 24v? I do not have a multi meter and need it for 12v. How do i set 12v without a multimeter?
Hello. Because the output voltage is variable, it cannot be set to 24 volts without a multimeter. Can you help someone with a multimeter for a few minutes? It is enough to set the output to 24V once
Pm me can you to install do solar panel of charger _
Can I use this to tranform 3.3V to 1.5V?
No it does output of 4.5V to 40V
yes you can:
Output: DC 1.5V to 35V voltage continuously adjustable,
Input: DC 3V to 40V
The output of this module is 1.5 to 35 volts
Pm me can you to install do solar panel of charger _
@@newtecpro Must I also connect the Negative iinput and Output . And can it working If i onnly connect the Positive input and outPut
is this buck or boost combo convertor model ???
It is a buck converter model
Load Capacity ?
Normal is 2 amps and training mode using heatsink is 2.5 to 3 amps
Pm me can you to install do solar panel of charger _
Please make your question more clear. I din't notice. Thank
demokracja a co to jest
؟
Pm me can you to install do solar panel of charger _