ฝัง
- เผยแพร่เมื่อ 19 ก.ย. 2024
- #4x4 #offroad #diy
The long awaited Locker install!! This epsiode marks the start of Coal 2.0 and i couldnt think of a better way to kick it off than a Auto Lokka up front!
Now its time to test it off-road, YEWW!
This DIY video shows that two guys that have never done this before can go ahead and install the Lokka aswell as rebuild the front hubs!
The cost of the LOKKA is around the $600 mark making it the cheapest option to lock most 4WDS! Head on over to 4WD Systems to grab one for your rig!
4wdsystems.com...
TAGS: Locker lokka locked twin front rebuild hubs bearings how to install lockers gu gq patrol 4x4 4wd off-road overland rock crawling front vs rear
LSD build how to DIY do it yourself 35s beadlocks lifted lift wheels locked lock auto lunchbox
SUPPORT ROAM LYFE: roamlyfe.com
INSTAGRAM: Roam_Lyfe
#build #4x4 #offroad #4WD #DIY #4x4
Loving the content mate , I ran a front auto lokka in my old nl pajero fully transformed it offroad and was hands down thr best budget mod I added. I must say it's nice to see content from an everyday aussie who isn't sponsored and builds a rig within the everyday Aussies budget .
Mint video mate. Great run down showing the process which a lot of others don’t go into such detail. Personally unless they are brand new I would just replace the wheel bearings. They are cheap and the most common fail point on a patrol. Not worth using old bearings. If they are still ok just keep them as spares for when you go on trips.
You'll stop thinking about a rear locker when you experience what a difference this makes. Had a Lockrite in my GU for 11 years, first mod I did from new. At the time it was $400 and I installed it myself no issues. Lokka has same operation as Lockrite.
Needs to run a bottle of engine oil flush through the rear diff for 500kms then drain and fill with new oil. That will clean up that lsd friction plates making it work almost like factory new again. Patrol plus lsd plus a front lokka = legendary performance 👌👌👌
Love ya work bud good to see Aussies doing this stuff
Thanks legend!
Great job as always. Just an FYI on the bearing nut. It needs to be torqued to 167nm - 196nm, spun a few times in both directions, backed off them torqued again to 5nm then locked off. This allows the bearing race to seat and spin freely.
Each video, the videography and editing gets better. So good 🤙🏻
I hope so mate! I wanna upgrade the camera setup so I can get better low light performance 🤘
Yep keep it up love coal and your vids!
Thanks legend!!
love that castrol lmm grease, works great for rc car diffs. I'd also invest or make my own hub nut tool instead of whacking them 👍
It was recommended by a friend!! Also that tool is next on the list!
Great work. Keep up the great craftsmanship and hard work my friend. Fab On. Weld On. Keep Making. God bless.
Love the work mate can’t wait to see cole and the camper on the road 🤙🏽
The Legend has posted
Yeww finally
Good video. I have a lokka in front of gu, elocker in rear. Works a treat. Cheap and cheerful. When on a budget..
First had to click on it knew it would be great before watching it 👍
Thanks legend!!
I reckon you'll find the Lokka and LSD combo will be more than enough for you. I'd keep her in until she needs her own maintenance and then swap.
Got the same Lokka in my GQ wagon ,, is mint there fine in the sand i find ,, unless you full send up cullcup hill and throw all ya belts and only have a alternator water pump spare ,, so you run up deep powder sand at 10psi with a auto lokka with a tight right handler up the top hahahah was much Armstrong steering going on
Ahaha that’s funny we were just their in Pemberton
😅
Very Nice video and you have a very Nice rig. Keep up the good work 👍
Thanks Thomas!
I normally take a photo after every part I take add. Take 100 photos and can delete them after. Id also take photos of how the parts are laid out
Diff oil in the swivel hubs is annoying because it leaks easier but it does a better job for bearing life then grease does.
13:40 as a fitter and turner, take photos, heaps of photos.
Yeah photos of how the seals went in woulda been great 😅
Awesome vid..I put a locka the same as yours in the front of my ln 106 and love it..so I put a locka..same brand..goannawhere..in the rear..because it would b tough..take out the LSD and replace with auto locka..BIG mistake if u need to use your vehicle for around town use..6 months later I took it out..because the noises that it made scared the shit out of me..it sounded like I was snapping an axle when u went around roundabouts and other normal driving procedures on the bitumen.. double locka in the bush..awesome....on the black top..bloody terrible..when I took the rear locka out..and inspected..it was in perfect condition..much to my surprise..goannawhere is a tough product..
great instructional video! looks really good ! well done !
Should just throw a shim in the lsd. Not a hard job either. Done it in my gq and front arb locker and works mint. Might have to put a thicker shim if your lsd doesn’t work that great? Have 3wd always till I turn the locker on.
Was thinking about going a .55 shim in the back to tighten it up! What size did you go?
@@RoamLyfe yea man that’s the size I went. They’re pretty easy to do if it’s not locking enough. The bloke at road runner told me that .55 will lock a good lsd and a .70 if it’s a worn out
Real helpful vid mate. Just about to put an auto lokka in my 45
Most useful swivel hub rebuild video even though that wasn’t the reason of the video!
Hahah! I watched a couple sketchy ones hey!! 😂
Very cool build🤙Man I wish I could get a gq one day but with the current states of four-wheel drives it ain’t happenen soon😂
I haven't been running them king pin cup things for nearly 3years now🤣 I heard some people don't bother putting them back in so I done the same and no dramas yet with my swivel hub
I did get told that haha, Probly shoulda just left them! Hha
Manufacturers do lots of testing, if they weren't needed for longevity.
Nissan would have saved millions not installing them.
Yes keep up the good work there's a lot of stuff iam Learning 👍🏾 👌
Can't wait for more mods and what lift pump you using and how it was installed it will be great Cheers legend 👍🍻
The lift pump was installed prior to my buying but it’s just a 12v ticker pump installed just above the tank in line!
Mint work mate, i just did my front arb locker in my patrol, it's not as hard as it looks just fiddly hey haha. I almost went the autolokka route but was worried I'd stuff it up haha
Yeah once you know what you are doing you could smash one out pretty quick! But Yeha a little fiddly, the hubs where worse in my opinion 😂
@@RoamLyfe hubs are definitely much more annoying lol
Mate coal is gonna be a beast now!
Nah need to leave some of the stuff ups in, it’ll give us more confidence 😂
Hey man, killer vidoes. Just wanna let you know that u killes your battery if u put it on concrete.
Oh really?? You mean in the car or when it’s out of the car?
Not on modern batteries... Decades ago it used too due to the construction of them.
Not at drama nowadays.
Loving your content, giving me something to do on ACC. Cheers mate
Awesome Video, keep up the great content.
Thanks legend!
No stealing that unless you got a spare battery 😂
“Now the hardest part for me… is this bloody dog” 😂
😂😂😂
Awesome stuff mate keep it up
Thanks mick!!
11/10 video again king
Thanks legend!! 🔥🔥
The crown wheel only goes on one way no need for punch marks
The punch marks where for the end caps as they are setting the pre load on the crown wheel! The caps are very important that they go back to the same location!
Aye brother I’m from NSW and
Was up on holidays in the bad rain in qld I was coming up the back of burpengary station and noticed the bogan bus is he from down then ways brother
If so I need to hit him up to go out with the bus and coal as I own a gq wagon my self on 35s
Keen to see your thoughts on the lokka. I'm considering one/detroit auto locker for my GU as I've heard a lot of people swear by them over air/e lockers which seem to break..
P.s. when rebuilding your swivel hubs source the heavy duty inner bearing seal in the hub and the trail safe axle seals. They shit all over the oem seals which just leak and break easily letting in water and forcing you to tear everything apart again in no time.
Edit just watched vid whole way through and saw you got the right axle seals good stuff.
I’m bloody keen to test it out! The research I did see that most people where very happy with an auto front and a manual rear setup!
Yeah I definitely got told about those inner seals! Glad I went that rout 🤘🤘
I have a Lockrite autolocker in my GU, best mod of all. Just do it.
@@einfelder8262 yea pretty keen. I figure if I'm going 4wd'ing I'm literally doing that so why screw around with switches. Some will say it can cause wear etc but I just don't see how that argument stacks up.. The only issue I can see is if you catch yourself out on some dodgy angles and pop a cv
@@Nick-sd7um The autolocker doesn't cause wear, nor does it cause CV damage. I busted a hub once and had to travel the full length of Fulton's Creek Track with only one front driving - pulled a bit to the driven side but still got me out onto Walhalla Rd. The only issue I have found is when reversing uphill on full lock, as when going around downhill switchbacks, it can wind up. Solution is to come off full lock to reduce load on inner wheel a bit then all good. Note that this will also occur with a switchable locker, which may not release if you switch it off under the same load.
@@einfelder8262 awesome thanks for the info
Hey bro luv your works just wanted to know where did you get the Chinese bead locks from and what did you pay for them many thanks
I always take pictures with my phone so I can go back and see how it put together.
🥳🥳 can’t wait for more videos
🔥🔥
Very informative. I'm learning a lot from your videos. What tool did you use in placing your axle seals 17:45?
i have an auto locker in my 80 series front... works great, makes a bit of noise on full turn... my biggest hate is that when your hubs are locked in and in 4wd high gears... the steering fights me, does get annoying
Yeah that’s a good point!! I’m hoping it’s not to bad, will he a bit of a learning curve for sure! If it’s annoying we will swap it out to a manual locker!
@@RoamLyfe yeah mate, lokka are cheap as, great for what they are. But I'll be swapping mine out when i win tattslotto
If it's making noise your backlash is wrong.
When set up correctly, they're very quiet.
How good
Thanks Lachlan 🔥
Hey mate how much is Harry’s patrol lift front and back and how big are the tyres? How many kms on it??
hey dude, what do you use to film your videos? gopro or camera?
hey mate! been watching for quite a while.
with coal i see the exhaust poiints directly on the tyre... wouldnt this heat the tyre up more than the others causing uneven wear? and maybe moisture on the tyre too?
Yeah I do want to change the setup a bit with the exhaust, main reason I want to is because it makes the wheel really dirty within no time.. mignt look at a rear exit!
Bloody mint
👌👌
well shiet its about time
I know right 🤘😅
Just ordered my sticker ya only had pink left so pink it is 🤣🤣🤣
Oh you bloody legend!! The pink is hot 🥵
@Roam Lyfe it's gunna stand out 🤣🤣
Take a picture of the laid out parts? Just occurred to me that you have the video. DOH
Yeah haha 😂 I just ended up doing the exploded view trick haha!!
Your steering wheel is on the incorrect side, start with that.
Can you do a POV mate
As in go pro on the head??
@@RoamLyfe Yeah and just drive around 👍
Road and Off -road
No pattern check? wtf lol
We did check it mate!
For the price of wheel bearing set it’s not worth putting the old ones back in!
My wheel bearings are less than a year old!! 🤘
Tbh cole is to good looking to be sitting outside
It’s like a diamond in a turd pile lol
Dont put the caps back in u dont need them
i need a locker in my jeep... badly
I’ve needed one for ages!! So glad it’s finally done!
if this is ur daily u must be mad about fuel prices
Haha luckily it’s not my daily!! 😂
Thumbnail says coal 2.0 but only puts in a loka
It’s the start of coal 2.0!!
Once you buy a selectable locker you will never go back
Yeah one day we might chuck one in! I’m keen to learn how to drive with the auto tho!!
Yeah don’t get me wrong there great for how cheap they are 👍
@@reyneroulston578 I’d love some air lockers just for the noise haha
Why would you want to get stuck and not be able to turn.