RAMPS 1.4 - BLTouch
ฝัง
- เผยแพร่เมื่อ 22 ก.ย. 2018
- This is a brief tutorial on how to install BLTouch on RAMPS 1.4.
One Time Tips, You Can PayPal Me:
www.paypal.me/EBraiman
Discord:
/ discord
Patreon:
/ edbraiman
Required Hardware:
1- Arduino Mega 2560
1- RAMPS 1.4
1- BLTouch
Software:
Arduino Studios 1.8.5 or higher
Marlin Firmware 1.1.9 or higher
Pronterface.exe
Beautifully done. If only all tutorials were as crystal clear as this : )
This helped me to debug an issue with my RAMPS 1.6 plus installation. Great video, thanks for the good info!
You're welcome.
Is the pinout different for a CLTouch from a Creality Ender 3 S1?
Thank you for a VERY clear and concise video!!!
You're welcome.
Can you make a video to show how to set the adjustments for the probe to the extruder in the configuration.h file. ? You make some damn good videos!
really thank youu
Great video! Thanks!
You're welcome.
I ask you a question everything I undefined for BLtouch because I already installed BLtouch but I want to Auto leveling every point of XY bed axis but my BLtouch is only level in center of bed
There's a Discord link on my TH-cam channel. General chat and a BLT chat exist there.
Saludos desde Colombia. Que marca es el bltouch que utilizas o que referencia me recomiendas.
cuando grabé esto, creo que tenían una versión anterior a la 3.0, pero cualquier BLtouch debería funcionar. Recuerde que esto estaba en una versión muy antigua del firmware de Marlin.
what if i have a fan adapter on the 3 servo pins?Is there an other solution?
You can look for a free volt pin that matches on the board with a ground and signal pin. Then reassign signal pin number for device in pin file.
Why my BLtouch is not Auto bed level every point of my bed ? Only in center
Why you should put your thumb on BL touch on 10second?
Can this also be applied to the 3DTouch clone sensor? I can't seem to get it working given this setup and it's driving me nuts. @_@. Though it works flawlessly on the Anet A8 board setup. I just want to upgrade the board to ramps 1.4 so I can change the stepper motors to the TMC2130's stepper modules. I'm always getting this error message "[ERROR] Error:STOP called because of BLTouch error - restart with M999" and "[ERROR] Error:Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
The process maybe the same, but would need to try first.
i have a 3d clone sensor chinesium knock off and this procedure for me work flawlessly:)
Thank you. Could you post a link?
So I just installed my BL touch, but whenever the printer srarts to home Z the printsr loses power and the LCD flickers and then displays the Marlin Splash screen. Any ideas what the problem may be?
What happens when LCD is disconnect? Which type of LCD? Which version of Marlin firmware? What else is connected to 3d printer board? Do you have Pronterface connected via a serial USB connection and what error message may display in Pronterface?
Also check the power supply wire connections.
@@EdwardBraiman First off thank you so much for your help.! I am running Marlin 1.9, with a Reprap Full Graphic Display. I just tried disconnecting the LCD and using Pronterface and that seems to have worked just fine. It's a real shame though because I really wanted to be able to print without a connection to a computer
Try reconnecting the LCD and see if error pops in Pronterface. They may share a pin or something else might be going on you'll see occuring.
@@EdwardBraiman ah ha. The issue was the extruder heatsink fan. Once I unplugged that the LCD and BL Touch work fine together
what if i am using a button with only 2 poles? how would i alter the program to allow that?
Could you give me more of a description of what you're trying to do?
Do you mean a switch like an Endstop?
@@EdwardBraiman yes but with 2 poles on the twitch instead of 3, where do i plug such a switch in and where do i alter the code to make it work?
It would be similar to my switch video for Endstop. You'll use ground and signal pin. The video you're looking for is in my playlist.
@@EdwardBraiman thank you so much. ^W^
I have the reprapguru prusa i3 with ramps 1.4 and marlin 1.1.8 and for the life of me I can't get the configuration.h file right. The commands work manually but when trying to home z it just keeps going up. Please help someone!
Remove power from RAMPS 1.4 and flip direction of z-axis nema connection. The power up RAMPS 1.4 and retest.
@@EdwardBraiman I figured it out. I just had the z probe hooked up to z max instead of the z min.
I actually have marlin 1.1.6. I would love to update but then I would have to go thru configuration.h and that would take forever unless you or someone else knows an easy way to do it.
Anyway you can download Marlin without doing a full day on Github???
Thanks.
When my bl touch deploys it causes the printer to restart even with the jumper for the 5v. Any ideas?
Does the hotend or heatbed do this as well?
@@EdwardBraiman no
Join my Discord and myself or someone else in General chat can walk you through the issue.
If you install BLtouch you can Remove now z endstop
Normally I run one or the other.
You forgot the most important part of jumpering the 5v vcc rail near the servo. This won't work otherwise.
Maybe. I'll need to check. Nice catch.
1:45 he does
He did.
he duds