I’ve installed the 1.2 B now on a Cube AMS with Bosch SX motor. In the first installation I did obviously not follow the stepwise procedure correctly. When riding the bike I always got the orange warning lamp after short distance. I did reset the Box and re-installed it once again following the recommended steps. Now it works properly. The support is continuous up to the limit and it fades out smoothly at 35/36/37 you keep on pedaling. My bike has no display, I use the SpeedBox App, which works nicely as well. I like the system and would buy it again.
Nice video, but what about Bosch system without the display only with the battery indicator? There are plenty of ebikes nowaday incl. mine with Bosch motor running without the display. 1) How do you check the Rim Magnet Simulator without having the speed value on a non existent display? 2) Tuning of the speed limit- how do you do it without the non-existent display?
Good day. If you don't have a display, you can check the speed in the Bosch Flow App. Or you can get the B.Tuning version (B as Bluetooth) and use our SpeedBox App.
Hello. Your question is absolutely correct 🙂 Countdown is the process of counting up the kilometers an e-bike would travel if it were traveling at a speed of 25 km/h. It is triggered if you have previously driven at a speed higher than 25 km/h. The Bosch Smart System is quite complicated and we have written some tips from experience to eliminate the risk of tuning detection: Drive at least 10 km before installing the tuning. If possible, do not use the Flow App. If you want to use the Flow App, turn off automatic updates and location and do not modify the speed limit, torque and riding modes. Do not activate/deactivate tuning during riding. Do not exceed a speed of 35 km/h. When stopping for a short time, keep one foot on the pedal so that the countdown does not start. When stopping for a longer period of time, allow at least a partial countdown to take place. After a long ride, the countdown may take several minutes. Do not remove the display if the countdown has not been finished.
@@SpeedBoxTuning This is great information and might help reduce the number of repeat Q&As if it was posted in the video description. Just an thought and thanks for this reply
@@HenrikdaMURDERERER Good day. If you don't have a display, you need a version called B.Tuning. Here you will see the ongoing countdown on the mobile screen in the SpeedBox App.
Hello. Electric bikes with Bosch motors are equipped with strong tuning detection. They attempt to detect any deviation in the data (e.g., speed vs. traveled distance, pedaling frequency, battery capacity, etc.). The maximum speed of 35 km/h is not dogma; this speed can be increased in the settings. But it is one of the preventative recommendations on how to avoid tuning detection.
@@SpeedBoxTuningOK, thank you, so even with the "countdown" process, the tuning could be detected by the unit ? In that case what would happen ? Is there a risk to have the ebike assistance completeley blocked ?
@@julienhardy If the motor is equipped with detection, there will always be a minimal risk of detection. However, the more you follow the recommendations, the more you eliminate the risk of tuning. If an error indicating tuning detection appears in the future, it can be removed without visiting a bike shop.
I have it on 50km/h, which is enough for 12 speed MTB. I had it on 35km/h, but i can go 40km/h almost all the time, so when speed hits the limit as it was 35km/h, it was jagging the motor that can be felt on pedals, and is really annoying, that's why it is on 50 although i don't go that fast anyway.
@@macremacer-my8ow Hello. The possibility of setting one's own speed limit is intended as a prevention, so that the rider can check that his maximum speed does not exceed 35 km/h.
Hello. 35 km/h is the preset maximum speed. We recommend it for prevention against tuning detection. You can change the set maximum speed and drive at a theoretically unlimited speed. But it's something to consider. We would prefer not to drive above 40 km/h.
@@AndyMialkowski-ct9sz Hello. If the system detects tuning, you have two options. Either visit a bike service and have the error erased, or you can ride for 90 minutes without assistance. 90 minutes is really the maximum. In practice, several tens of minutes are enough. You can also interrupt the ride. After that, we recommend riding another 10 km without tuning on. Change gears and assistance modes while riding. After that, the detection will definitely disappear.
@@SpeedBoxTuningThank for your reply. That is, when it detects tuning, it blocks the assistant. Does it? According to your observations, does tuning detection often occur? (When setting the limit up to 40 km/h) In the old e-bike (Bosch CX 4th gen), I set the limit just up to 40 km. This is the optimum for me. I am even able, on a straight road, to propel the bike up to 46 km/h without assistance (If the motor helped me before) Here comes the critical question. How often will an error appear in the Smart System when I set the limit for this 40 km? Thank you.
@@AndyMialkowski-ct9sz There is no empirical answer to such a question. In the Smart System, dozens to hundreds of operations take place that can detect tuning. For this reason, we have an entire set of recommendations on how to reduce the probability of tuning occurrence to zero.
I don’t have any place inside of the housing to store the rim magnet simulator. Can it be placed on the outside. I drive through a lot of mud and do 50km a day in rain and other weather. Is it very weatherproof?
Hi. Each of our SpeedBoxes is waterproof and an externally placed chip will work, but we cannot guarantee absolute functionality all the time if you will be riding off-road through mud and puddles. It's up to you 🙂
mine doesn’t work at all. the magnet simulator doesn’t pick anything up, it does not tune and what do you mean “check wheel circumference”? check against what?
Hello. First we will answer the wheel circumference: usually it is preset and you just have to confirm. This step is used to set the displayed speed. As for the magnet simulator, we recommend a little patience 🙂 Spin with the crank, not the rear wheel. As soon as the display shows any speed value other than zero, turn the ebike off and on. At this point the system will "understand" that it will follow the data from the magnet simulator, not from the Rim magnet. If you still don't know what to do, please contact our support at speedbox-tuning.com, Facebook or Instagram. Thank you
i got it to work. i emailed support and they explained the magnet simulator needs to be as central as possible. where they wanted to me to put the magnet simulator within the motor compartment, i had a metal block which didn’t allow me to fit it in. I put the magnet simulator outside the motor compartment, centred, and that’s worked. this might help someone with same issue i had.
@SpeedBoxTuning, am I understanding this correctly? at the moment of it indicating speed value. in that moment, turn off bike? or only once it is 0 out?
When I install it, if I turn the tires, it doesn't show any numbers on my display. Even if I position the magnet differently, it doesn't show anything on the display
Im having this same issue. did you get it resolved? I have the new speedbox 1.2b and the CX Raceline. See no speed output on the kiox screen, even though it registers speed on the app. please let me know if you had any updates
Hello. It is not magnet. It's just a cut-off piece of foam cover from our box in which we send the SpeedBox products 🙂 You can use any piece of foam you want.
So should it work also without kiox (and use of flow app)?i am not getting speed signal at all with that spoke magnet. With origina rim magnet speed is displayed, but cannot get that tuning feature on. Should those 2,5 etc show in flow app? Thanks
One question.... how it reflects on battery life if your speed is 30km/h..... Does it drastically cutting mileage you can ride with charge or slightly?
Hello. This depends on the e-bike and riding style. Several times a season, we test the riding characteristics and range of our test e-bikes of all possible brands. You can normally ride around 70 km, if you don't always use the highest assistance.
Hallo, wie ist die Wirksamkeit von Speedbox 1.2, da ich hier unterschiedliche Meinungen lese und niemand schreibt, dass alles in Ordnung ist, dass es seit einem halben Jahr funktioniert und es keine Probleme gibt.
Hallo. Was die Softwarefunktionalität anbelangt, ist der Chip vollständig kompatibel mit Bosch-Motoren mit einem Magneten am Felgenrand (einschließlich des SX-Motors). Die Installation erfordert etwas Geduld, da zunächst eine Spule (Rim Magnet Simulator) korrekt im Motorraum befestigt werden muss. Ein weiteres Problem ist, dass der Chip und die Spule nicht in den Raum jedes Motors vollständig passen können. Dies ist kein Fehler der Chip-Kompatibilität mit dem Elektromotor, sondern hängt vom Typ des Elektrofahrrads ab. Daher empfehlen wir, vor dem Kauf des Produkts den Motorraum zuerst zu überprüfen.
Hello. It probably doesn't matter, but personally, we would install the lights first. If everything works correctly, then install the SpeedBox. Thanks.
Hello. Installing the ebike chip will not cause any damage. OTA (FBL) firmware updates are still possible after installation, but we strongly advise against them - especially for electric bikes with Bosch motors.
Good morning. Yes, Flow App is not affected by SpeedBox functionality. However, we recommend turning off automatic updates in the settings in order to preserve the correct functionality of the chip.
Good day. You can also drive at a higher speed, but at your own risk. We and other tuning manufacturers recommend not to exceed 22 mph precisely to prevent tuning detection in Smart systems.
R u working on a new one? When u say set the limit to 35kmh is that the official 35km Or the 35km on the the app? So ur really doing 45km. Video says the speed will show lower on the the screen
Hello. You can theoretically set the speed to unlimited. However, we recommend not exceeding 35 km/h to reduce the risk of tuning detection. Therefore, we default to a 35 km/h limit from the factory. The actual speed can be seen in the SpeedBox App. The display shows a slightly lower speed. For example, 18 km/h on the display means 25 km/h in reality. 25 km/h on the display means 35 km/h in reality, and so on.
Hi can you please help , i have installed following video and guides , but i am getting speed sensor readings from every part of the motor no mater what , and it wont give assist past 25km/hr still. Do i need to be on a certain firmware ? I did not update firmware , should i maybe ?? Any help eould be great , thanks
Hello. I have got a Speedbox for rim magnet. I updated my bike's firmware by mistake at the last version, and now the speed box doesn't work. Do you know if it is possible to downgrade the bosh firmare?
Hello. If you already have updated firmware, try disabling SpeedBox according to this video. You do not need to remove the chip from the e-bike. th-cam.com/video/dCuxoid3u4M/w-d-xo.html Then ride the e-bike for about 10 km without tuning and then try to activate the tuning again according to the video.
Hello, I have the FLOW application version 1.21.3, I don't download anything, I don't update anything. Will speedbox work?? bosch cx gen 4 kiox 500 engine.
Hello. Starting from May 2024, we supply products compatible with the latest software version 11.3.0. The products should be also compatible with Flow App 1.21.3.
Hallo. Uns ist kein Chip bekannt, der nicht in den Focus gepasst hätte. Natürlich muss man manchmal Geduld aufbringen. Wenn du nicht weiter weißt, kontaktiere unser Support-Team unter www.speedbox-team.de oder über Messenger / Instagram.
@@TopHardyYT Genau das war meine Frage, ich denke dass passt nicht. Ich hab mir diesen italienischen eplus Chip gekauft, aber der produziert ständig Fehlermeldungen.. Da heißt es wohl abzuwarten.
@@sacredtjiss Wir entschuldigen uns für den nicht funktionierenden Link. Hier ist der Link zur idealen Position des Rim Magnet Simulators. chrome-extension://efaidnbmnnnibpcajpcglclefindmkaj/tuningelektrokol.s9.cdn-upgates.com/i/i6642f643486f3-sb12-b-mag-connection.pdf Oder Alle Informationen finden Sie auf der Website: www.speedbox-tuning.de/smart-system-rim-magnet.
Hello. I try to install the speedbox on my canyon strive on cfr. It has no display only a central battery indicator and a small wireless controller on my steer. In the bosh app you can see the speed to place the rim magnet simulator correct. That worked fine. Then if you want to ride the speedbox is on when you start the bike en i can ride 30 kmh+- but after 300m the led on the battery status flashes Orange, But no errors when you restart the bike (without rim magnet) it works again for another 300m. How do you check the weel circum whitout a display or can you skip this step? How to check of your chip is enabled or disabled (2.5KMH and 3.5KMH on display) with only a battery andicator?(you cant use the app for this right?) Anyone advice on that orange led on the battery indicator? Thanks in advance
Good day. You can check the wheel circumference in the Flow App. This step is not necessary for all types of bikes, it is recommended for preventive reasons. If you do not have a display, it is not possible to verify whether the tuning is currently active or inactive. If the LED flashes orange as an error, we can recommend trying to slightly change the position of the Rim Magnet Simulator. If the problem persists, we recommend replacing or returning the chip.
Buenos días. Si todavía tiene problemas con el error 523003, intente seguir estas instrucciones: tuningelektrokol.s9.cdn-upgates.com/i/i6642f643486f3-sb12-b-mag-connection.pdf
Buongiorno. Io possiedo una M20 Orbea con motore Bosch Performance Line CX, senza display e con software 9.13.0. Ho installato lo SpeedBox 1.2 (Smart Sistem+Rim Magnet) ma contunua ad andare in errore. Cosa devo verificare? Grazie
Buona giornata. Se non hai un display, dovresti avere una versione chiamata B.Tuning. Prova a guardare la nostra pagina dei manuali www.speedbox-tuning.it/um-speedbox-1-2-b-tuning-per-bosch Oppure puoi contattare il nostro supporto su speedbox-tuning.it o tramite Messenger o Instagram.
Hi. SpeedBox for Bosch Smart System products manufactured in April 2024 and later are compatible with the latest update. In theory, there should be no older models on the market now. If you have updated software with the serial number 13.x.x, it may happen that the activation using the Walk feature will not work now. It will be necessary to activate/deactivate the tuning using the combination of buttons - + - + or + - + -.
@@andysims8823 Hi. We have experience with e-bikes with a Bosch motor at speeds above 50 km/h (for a short time), the sustainable speed on a flat surface is around 40 km/h. However, for engines with the Smart system, we recommend not to exceed an average cruising speed of 35 km/h to prevent the risk of tuning detection.
Bonjour, j' ai eu énormément de mal a le monter sur un moustache game.(très peu de place entre le cadre et le moteur pour le simulateur rim magnet) et pourtant je suis très bricoleur, mais j' ai quand même réussi. Maintenant le problème en a peut près 400 km j'ai eu 4 détection de manipulation donc 3fois bloqué 90 minutes et maintenant il se débloque plus 😢. Comment je fait maintenant ?
I do not recommend this !! After speaking to an agent and confirming it would work without an issue I bought one . Now the bike is telling me error 504 !! GREAT !!! Now it needs to go in the shop to resolved issue, who will pay for this ??! The bike is currently in limp mode !!! Useless. DO NOT BUY SPEEDBOX
Hi. We are sorry to hear that you have had tuning detection. With the SpeedBox for Bosch, we recommend following some recommendations to eliminate the risk of tuning detection (524001). All manufacturers have these recommendations. You can find them, for example, with individual products on our website www.speedbox-tuning.com/for-bosch. In case of questions, we recommend contacting our support on these pages or via Messenger or Instagram. Thank you for your understanding and many happy miles.
Good day. What exactly is the model name of your e-bike? Try to pick up the signal like this: set the derailleur to middle gear. When searching for a signal, turn the crank, not the rear wheel. Here www.speedbox-tuning.com/p/speedbox-1-2-for-bosch#1914 you will find all product and installation information. If you don't know what to do, contact our support at speedbox-tuning.com or Messenger or IG.
@@SpeedBoxTuning yes. The original setup has a magnet on the valve. The instructions for the SpeedBox say to remove this magnet. And replace with the sensor and spoke magnet
The signal from the rim simulator keeps getting lost every time because I have to take it outside my frame is not like in your video. Even when it does work, the error occurs again when I push human power into the pedals. I spent 7 hours trying yesterday, and today, I'm giving it another shot. I think I might have found the solution by fixing the speed sensor and securing the simulator strong in place. Hopefully, it will work better now.
@@BenjiBenji989 With e-bikes with a rim magnet, you have to patiently search for the signal of the magnet simulator. We recommend having the transmission set somewhere in the middle range. When testing the speed sensor signal, do not turn the rear wheel by hand, but turn the crank by hand. This should help in finding the signal. If you are unable to install the chip today, please contact our support at speedbox-tuning.com. Thanks.
Hi, I received the speedbox 1.2 tuning version. The only strange thing is that when I accelerate hard, the speed exceeds 25 km per hour on the "flow app" counter and therefore the engine stops for a second. Then, still on the flow up application, the speed automatically drops below 25 km per hour and the engine comes back into action. The problem with this is that when I accelerate up to 35 km per hour, there is always a moment where I have the engine cut out for a second or two. Do you think this is normal?
@@olivoliv7769 Hello. Yes, it is possible. Based on our experience, we recommend this: do not use the Flow App while riding. If you are already using it, please turn off automatic updates and positioning (so that your speed is not detectable through GPS) and do not make changes to the settings in the Flow App (do not modify the speed limit, torque and riding modes).
@@SpeedBoxTuning Thank you for this feedback, I will try it. in the Flow application I have the following informative message: Magnetic field of the rim magnet too weak. but this does not block the use of the bike. is this message normal? THANKS
Hello. No, the max speed is unlimited. The default max speed is 35 km/h, you can change it in settings. We recommend this speed to avoid risk of errors 🙂🤝
@@e-mike9776 Hello. Right now, we would recommend to uninstall the chip and pedal on the e-bike for about 90 minutes. (You don't have to ride the whole 90 minutes at once, the ride can be intermittent). Once the error is gone, you should make a few more calm rides without the chip (to get some new and clear data in the e-bike), only after that you should install the chip again. Do not ride only in Turbo mode during those calm rides, better to engage Tour, Eco, etc.
Hi. The SpeedBox 1.2 for Bosch is compatible with your e-bike. We recommend thoroughly watching the installation video and being patient when searching for the magnetic coil signal.
Hello, what is technically the difference between the Rim Magnet and the normal Magnet? They have the same function and get one signal per turn if the magnet is passing, right? I am engineer and would like to understand why you need to use different speedboxes for this.
Hello. In simple terms, a speed sensor with a common magnet works in such a way that each rotation of the rear wheel is captured by the sensor as one pulse. The number of pulses in time and the diameter of the wheel gives the speed, ODO etc. The magnet on the rim is wireless and uses the electromagnetic field from the electric motor. The advantage of the rim magnet is the ability to read riding data directly from the electric motor (more precise data). And it also makes installing the tuning more complicated 🙂
@@SpeedBoxTuning Thanks for answering. And what is the difficulty to show the real speed with the rim version like 23,5 for 35 km/h? What I understand is that you simulate the movement of the rim magnet with an electric coil, the motor is reading the movement of the magnetic field directly without additional sensor like the speed sensor.
Доброе утро. Код ошибки 524001 - это обнаружение настройки производителем двигателя Bosch. К сожалению, обнаружение тюнинга - неприятность, с которой приходится сталкиваться всем производителям тюнинга. Чтобы вам не пришлось посещать велосервис и платить за разблокировку, мы рекомендуем следующий порядок действий: Удалите SpeedBox из движка. Ездите на электровелосипеде без посторонней помощи около 90 минут, иногда достаточно меньше. Не обязательно сразу ехать, можно прервать езду. Как только ассистент двигателя снова заработает, проедьте не менее 10 км, переключите передачи и режимы ассистента. Это перезагрузит систему. Затем вы можете переустановить SpeedBox. Вот рекомендации по предотвращению обнаружения настройки: Мы рекомендуем не обновлять прошивку вашего электронного велосипеда. Обновление увеличивает риск обнаружения настройки. Отключите автоматические обновления в настройках потока Ebike. Гарантия не распространяется на неисправность продукта, вызванную обновлением двигателя. При кратковременной остановке рекомендуем держать одну ногу на педали, чтобы не запустился счетчик пробега. При остановке на более длительный период пропустите хотя бы частичный дополнительный километраж. Не снимайте дисплей, чтобы заблокировать электровелосипед, пока не пройдут оставшиеся километры. Активацию/деактивацию настройки всегда следует выполнять во время остановки, а не во время движения. Мы рекомендуем не превышать рекомендуемую максимальную скорость 35 км/ч.
Hello. When did the error appear? While driving or during installation? If error 503 appeared, it means a weak magnetic field. It will help to either turn the ebike off and on, or move the magnet and try the signal again and then turn off, turn on. We also recommend turning with the crank, not the rear wheel. If you are not sure, please contact our support at speedbox-tuning.com. Thank you.
@@Joeyriot473 Installing tuning for ebikes with Smart System and rim magnet is a bit complicated. Could you please contact our support with the specific problem and type of your ebike so that we can find a common solution? Thank you.
Before buying an e-bike, it is good to think about whether I want to unlock the speed limiter or not. If so, it is better to get an e-bike with a simpler system. The Smart System with a magnet on the rear wheel rim is not that complicated in itself, but some e-bike manufacturers have mounted the electric motor in such a way that the installation of the tuning can be a bit more complicated.
@@SpeedBoxTuning It says on the internet that the Speedbox 1.2 no longer works from version 9.13.0, and I have already bought the box and now it doesn't work. The Speedbox 1.2 cannot be updated either, what is the solution? I need solutions!
@@ulasdemiroglu2518 Hello. SpeedBox does not work since version 11.13.0. If you have a lower version of the software, we recommend not updating. Ideally, turn off updates in the Flow App. However, we should have an updated product available next week. We recommend that you then contact your distributor for a replacement.
@@SpeedBoxTuning yes, but my dealer won't take this part back and I'm left with the costs. The part cost me $399 and doesn't even work. Speedbox doesn't care either.
@@lekatr6815 Hello. We don't know exactly what you mean. Place the magnet simulator in the center of the motor. And place the speed sensor on the side where there is no chain so as not to damage the speed sensor.
@@lekatr6815 Hello. If you don't have a display, you just have to let the countdown run until the e-bike turns off. After a long drive, the countdown can last up to 10 minutes.
Not working on my bike. @speedbox help please. I have the new speedbox 1.2b and the CX Raceline. See no speed output on the kiox screen, even though it registers speed on the app. Even when I turn on the speedbox its shows no output on the kiox. Please contact me. Regards, Ghulam. Ps: I sent you an email.
I’ve installed the 1.2 B now on a Cube AMS with Bosch SX motor. In the first installation I did obviously not follow the stepwise procedure correctly. When riding the bike I always got the orange warning lamp after short distance. I did reset the Box and re-installed it once again following the recommended steps.
Now it works properly.
The support is continuous up to the limit and it fades out smoothly at 35/36/37 you keep on pedaling.
My bike has no display, I use the SpeedBox App, which works nicely as well.
I like the system and would buy it again.
Hi is yours still working good, looking at getting one for my bike but have seen too many mixed reviews,
thanks
Is it still working ?
how long did it take you to install the speed box, the bike shop tells me it takes 5 hours to install but i can’t believe that
لم أعتقد أن هناك أشياء جميلة فدراجتكم❤
أنا أحب الدرجات كثيراً
Nice video, but what about Bosch system without the display only with the battery indicator? There are plenty of ebikes nowaday incl. mine with Bosch motor running without the display. 1) How do you check the Rim Magnet Simulator without having the speed value on a non existent display? 2) Tuning of the speed limit- how do you do it without the non-existent display?
Good day.
If you don't have a display, you can check the speed in the Bosch Flow App. Or you can get the B.Tuning version (B as Bluetooth) and use our SpeedBox App.
Hidup jangan dibuat sulit, hiduplah yang sederhana maka kau akan menikmati kebahagiaan
Hi, apologies for the basic question but what triggers the countdown? Ot cant be everytime the bike stops right?
Hello.
Your question is absolutely correct 🙂
Countdown is the process of counting up the kilometers an e-bike would travel if it were traveling at a speed of 25 km/h. It is triggered if you have previously driven at a speed higher than 25 km/h.
The Bosch Smart System is quite complicated and we have written some tips from experience to eliminate the risk of tuning detection:
Drive at least 10 km before installing the tuning.
If possible, do not use the Flow App.
If you want to use the Flow App, turn off automatic updates and location and do not modify the speed limit, torque and riding modes. Do not activate/deactivate tuning during riding.
Do not exceed a speed of 35 km/h.
When stopping for a short time, keep one foot on the pedal so that the countdown does not start.
When stopping for a longer period of time, allow at least a partial countdown to take place.
After a long ride, the countdown may take several minutes. Do not remove the display if the countdown has not been finished.
@@SpeedBoxTuning This is great information and might help reduce the number of repeat Q&As if it was posted in the video description. Just an thought and thanks for this reply
@@ccederlo Thank you for your comment and wish you many happy miles ☺
@@SpeedBoxTuning How do you know when the countdown is done, if you have the version with no display?
@@HenrikdaMURDERERER Good day.
If you don't have a display, you need a version called B.Tuning. Here you will see the ongoing countdown on the mobile screen in the SpeedBox App.
Hello what do you mean with "to minimize the risk of error codes, we recommend not to exceed 35 km/h." ?
Hello.
Electric bikes with Bosch motors are equipped with strong tuning detection. They attempt to detect any deviation in the data (e.g., speed vs. traveled distance, pedaling frequency, battery capacity, etc.). The maximum speed of 35 km/h is not dogma; this speed can be increased in the settings. But it is one of the preventative recommendations on how to avoid tuning detection.
@@SpeedBoxTuningOK, thank you, so even with the "countdown" process, the tuning could be detected by the unit ? In that case what would happen ? Is there a risk to have the ebike assistance completeley blocked ?
@@julienhardy If the motor is equipped with detection, there will always be a minimal risk of detection. However, the more you follow the recommendations, the more you eliminate the risk of tuning. If an error indicating tuning detection appears in the future, it can be removed without visiting a bike shop.
I have it on 50km/h, which is enough for 12 speed MTB.
I had it on 35km/h, but i can go 40km/h almost all the time, so when speed hits the limit as it was 35km/h, it was jagging the motor that can be felt on pedals, and is really annoying, that's why it is on 50 although i don't go that fast anyway.
@@macremacer-my8ow Hello.
The possibility of setting one's own speed limit is intended as a prevention, so that the rider can check that his maximum speed does not exceed 35 km/h.
In Africa we have 32km/h limit from factory. Does the speedbox push the limit higher than 35km/h?
Hello.
35 km/h is the preset maximum speed. We recommend it for prevention against tuning detection. You can change the set maximum speed and drive at a theoretically unlimited speed. But it's something to consider. We would prefer not to drive above 40 km/h.
@@SpeedBoxTuningWhat will happen when the system detects the tuning? Will it lock the motor?
@@AndyMialkowski-ct9sz Hello.
If the system detects tuning, you have two options. Either visit a bike service and have the error erased, or you can ride for 90 minutes without assistance.
90 minutes is really the maximum. In practice, several tens of minutes are enough. You can also interrupt the ride. After that, we recommend riding another 10 km without tuning on. Change gears and assistance modes while riding. After that, the detection will definitely disappear.
@@SpeedBoxTuningThank for your reply. That is, when it detects tuning, it blocks the assistant. Does it?
According to your observations, does tuning detection often occur? (When setting the limit up to 40 km/h)
In the old e-bike (Bosch CX 4th gen), I set the limit just up to 40 km. This is the optimum for me. I am even able, on a straight road, to propel the bike up to 46 km/h without assistance (If the motor helped me before)
Here comes the critical question. How often will an error appear in the Smart System when I set the limit for this 40 km?
Thank you.
@@AndyMialkowski-ct9sz There is no empirical answer to such a question. In the Smart System, dozens to hundreds of operations take place that can detect tuning. For this reason, we have an entire set of recommendations on how to reduce the probability of tuning occurrence to zero.
I don’t have any place inside of the housing to store the rim magnet simulator. Can it be placed on the outside. I drive through a lot of mud and do 50km a day in rain and other weather. Is it very weatherproof?
Hi.
Each of our SpeedBoxes is waterproof and an externally placed chip will work, but we cannot guarantee absolute functionality all the time if you will be riding off-road through mud and puddles. It's up to you 🙂
mine doesn’t work at all. the magnet simulator doesn’t pick anything up, it does not tune and what do you mean “check wheel circumference”? check against what?
Hello.
First we will answer the wheel circumference: usually it is preset and you just have to confirm. This step is used to set the displayed speed. As for the magnet simulator, we recommend a little patience 🙂 Spin with the crank, not the rear wheel. As soon as the display shows any speed value other than zero, turn the ebike off and on. At this point the system will "understand" that it will follow the data from the magnet simulator, not from the Rim magnet. If you still don't know what to do, please contact our support at speedbox-tuning.com, Facebook or Instagram.
Thank you
i got it to work. i emailed support and they explained the magnet simulator needs to be as central as possible. where they wanted to me to put the magnet simulator within the motor compartment, i had a metal block which didn’t allow me to fit it in. I put the magnet simulator outside the motor compartment, centred, and that’s worked. this might help someone with same issue i had.
Is It Waterproof Outside The Box
@@gerardrice7747 Hello.
Yes, the chip is waterproof.
@SpeedBoxTuning, am I understanding this correctly? at the moment of it indicating speed value. in that moment, turn off bike? or only once it is 0 out?
When I install it, if I turn the tires, it doesn't show any numbers on my display. Even if I position the magnet differently, it doesn't show anything on the display
Im having this same issue. did you get it resolved? I have the new speedbox 1.2b and the CX Raceline. See no speed output on the kiox screen, even though it registers speed on the app. please let me know if you had any updates
@@GhulamHussain-uk3im send it back, it's useless, a lot of stress for nothing, I sent it back. just crap the whole thing
very nice i like it
In the video 3:45 is there an additional magnet? Because you don't provide it in the set.
What is it and what is it for?
Hello.
It is not magnet. It's just a cut-off piece of foam cover from our box in which we send the SpeedBox products 🙂 You can use any piece of foam you want.
@@SpeedBoxTuning está solucionado el tema del error 523003 , tuve que devolver mi speedbox porque al cabo de varios kilómetros me salía el error
Looks not so good whit the magnet and to expensive
Still bought IT 2 Times i give it a try :)
Issues hm lets See...
@@BenjiBenji989Can u give some feedback? Im looking for one.
So should it work also without kiox (and use of flow app)?i am not getting speed signal at all with that spoke magnet. With origina rim magnet speed is displayed, but cannot get that tuning feature on. Should those 2,5 etc show in flow app? Thanks
Hello.
Yes, you can use the FlowApp instead of the display to find the correct magnet position.
One question.... how it reflects on battery life if your speed is 30km/h..... Does it drastically cutting mileage you can ride with charge or slightly?
Hello.
This depends on the e-bike and riding style. Several times a season, we test the riding characteristics and range of our test e-bikes of all possible brands. You can normally ride around 70 km, if you don't always use the highest assistance.
Hallo, wie ist die Wirksamkeit von Speedbox 1.2, da ich hier unterschiedliche Meinungen lese und niemand schreibt, dass alles in Ordnung ist, dass es seit einem halben Jahr funktioniert und es keine Probleme gibt.
Hallo.
Was die Softwarefunktionalität anbelangt, ist der Chip vollständig kompatibel mit Bosch-Motoren mit einem Magneten am Felgenrand (einschließlich des SX-Motors). Die Installation erfordert etwas Geduld, da zunächst eine Spule (Rim Magnet Simulator) korrekt im Motorraum befestigt werden muss. Ein weiteres Problem ist, dass der Chip und die Spule nicht in den Raum jedes Motors vollständig passen können. Dies ist kein Fehler der Chip-Kompatibilität mit dem Elektromotor, sondern hängt vom Typ des Elektrofahrrads ab. Daher empfehlen wir, vor dem Kauf des Produkts den Motorraum zuerst zu überprüfen.
Is it better to install bike lights before installing the speedbox?
Will there be a problem later?
Hello.
It probably doesn't matter, but personally, we would install the lights first. If everything works correctly, then install the SpeedBox.
Thanks.
Going to hold off for a bit, don't want to brick a new bike, doesn't seem reliable yet, ota firmware updates affected? Too risky just now
Hello.
Installing the ebike chip will not cause any damage. OTA (FBL) firmware updates are still possible after installation, but we strongly advise against them - especially for electric bikes with Bosch motors.
@@SpeedBoxTuning I will give it some thought, the 25 kph limit is annoying as my natural cadence propels me at about 27 kph
35 would be perfect
@@markcliffe7 Great to hear! ☺
Will this work with Flow+ and all it's features, like tracking, anti-theft functionality and alerts, etc.?
Good morning.
Yes, Flow App is not affected by SpeedBox functionality. However, we recommend turning off automatic updates in the settings in order to preserve the correct functionality of the chip.
Saying online it only lets it do 22mph. With this can I not put it on the crank arm to gain more speed or would it go in limp mode?
Good day.
You can also drive at a higher speed, but at your own risk. We and other tuning manufacturers recommend not to exceed 22 mph precisely to prevent tuning detection in Smart systems.
tried today, I've moved the unit in every position and the only one I get any movement on the speed I get a error with Error 523003
U Fonds the Problem?
Will you offer diferent speed sensor f.e. mount on brake disc?
😊
0:07
@@NandakaliBudha-g3iits rim magnet, not brake disc, its main reason to by this speedbox
Hello. No, now we have only this one.
R u working on a new one?
When u say set the limit to 35kmh is that the official 35km
Or the 35km on the the app? So ur really doing 45km. Video says the speed will show lower on the the screen
Hello.
You can theoretically set the speed to unlimited. However, we recommend not exceeding 35 km/h to reduce the risk of tuning detection. Therefore, we default to a 35 km/h limit from the factory. The actual speed can be seen in the SpeedBox App. The display shows a slightly lower speed. For example, 18 km/h on the display means 25 km/h in reality. 25 km/h on the display means 35 km/h in reality, and so on.
Hi can you please help , i have installed following video and guides , but i am getting speed sensor readings from every part of the motor no mater what , and it wont give assist past 25km/hr still. Do i need to be on a certain firmware ? I did not update firmware , should i maybe ?? Any help eould be great , thanks
Hi.
Please try to contact our support on speedbox-tuning.com or on Messenger or Instagram.
Thank you.
Hello. I have got a Speedbox for rim magnet. I updated my bike's firmware by mistake at the last version, and now the speed box doesn't work. Do you know if it is possible to downgrade the bosh firmare?
Hello.
If you already have updated firmware, try disabling SpeedBox according to this video. You do not need to remove the chip from the e-bike.
th-cam.com/video/dCuxoid3u4M/w-d-xo.html
Then ride the e-bike for about 10 km without tuning and then try to activate the tuning again according to the video.
@@SpeedBoxTuningi can't access the video. it's written that it's a private video
@@ioncaraja2340 Sorry. Now you can watch 🙂
@SpeedBoxTuning is this deactivation method the way to update firmware?
@@macremacer-my8ow Hello.
Yes, this is an option. But in general, we do not recommend updating the firmware.
Hello, I have the FLOW application version 1.21.3, I don't download anything, I don't update anything. Will speedbox work??
bosch cx gen 4 kiox 500 engine.
Hello.
Starting from May 2024, we supply products compatible with the latest software version 11.3.0. The products should be also compatible with Flow App 1.21.3.
Hallo, Passt es an das neue Focus Jam2? Da ist sehr wenig Platz zwischen Motor und Gehäuse.
Hallo.
Uns ist kein Chip bekannt, der nicht in den Focus gepasst hätte. Natürlich muss man manchmal Geduld aufbringen. Wenn du nicht weiter weißt, kontaktiere unser Support-Team unter www.speedbox-team.de oder über Messenger / Instagram.
Wo kann man beim Focus jam2 den rim Simulator denn rein schieben? Hat da jemand gemacht? Da gibt es ja kaum spiel wo man ihn rein stecken könnte?
@@SpeedBoxTuning Euer Link funktioniert nicht und eure Antwort macht auch kein Sinn!
@@TopHardyYT Genau das war meine Frage, ich denke dass passt nicht. Ich hab mir diesen italienischen eplus Chip gekauft, aber der produziert ständig Fehlermeldungen..
Da heißt es wohl abzuwarten.
@@sacredtjiss
Wir entschuldigen uns für den nicht funktionierenden Link. Hier ist der Link zur idealen Position des Rim Magnet Simulators.
chrome-extension://efaidnbmnnnibpcajpcglclefindmkaj/tuningelektrokol.s9.cdn-upgates.com/i/i6642f643486f3-sb12-b-mag-connection.pdf
Oder Alle Informationen finden Sie auf der Website: www.speedbox-tuning.de/smart-system-rim-magnet.
Hello. I try to install the speedbox on my canyon strive on cfr. It has no display only a central battery indicator and a small wireless controller on my steer. In the bosh app you can see the speed to place the rim magnet simulator correct. That worked fine. Then if you want to ride the speedbox is on when you start the bike en i can ride 30 kmh+- but after 300m the led on the battery status flashes Orange, But no errors when you restart the bike (without rim magnet) it works again for another 300m. How do you check the weel circum whitout a display or can you skip this step? How to check of your chip is enabled or disabled (2.5KMH and 3.5KMH on display) with only a battery andicator?(you cant use the app for this right?) Anyone advice on that orange led on the battery indicator? Thanks in advance
Good day.
You can check the wheel circumference in the Flow App. This step is not necessary for all types of bikes, it is recommended for preventive reasons.
If you do not have a display, it is not possible to verify whether the tuning is currently active or inactive.
If the LED flashes orange as an error, we can recommend trying to slightly change the position of the Rim Magnet Simulator. If the problem persists, we recommend replacing or returning the chip.
Did you get it work with that spoke magnet? Mine doesn't show any speed with that, no matter where simulator is located.
With original rim magnet and simulator speed is displayed but i can't set that tuning ON. Should that activation been seen via Flow app?
Buenas , habeis solucionado ya los problemas del error 523003? Que no hay manera de poner el sensor en su sitio y sale el erro al rato???
Buenos días.
Si todavía tiene problemas con el error 523003, intente seguir estas instrucciones:
tuningelektrokol.s9.cdn-upgates.com/i/i6642f643486f3-sb12-b-mag-connection.pdf
Difícil lo devolvi al no ser capaz de dar con el sitio de colocación@@SpeedBoxTuning
Buongiorno. Io possiedo una M20 Orbea con motore Bosch Performance Line CX, senza display e con software 9.13.0. Ho installato lo SpeedBox 1.2 (Smart Sistem+Rim Magnet) ma contunua ad andare in errore. Cosa devo verificare? Grazie
Buona giornata.
Se non hai un display, dovresti avere una versione chiamata B.Tuning.
Prova a guardare la nostra pagina dei manuali www.speedbox-tuning.it/um-speedbox-1-2-b-tuning-per-bosch
Oppure puoi contattare il nostro supporto su speedbox-tuning.it o tramite Messenger o Instagram.
I just updated my bike, will this still work?
Hi.
SpeedBox for Bosch Smart System products manufactured in April 2024 and later are compatible with the latest update. In theory, there should be no older models on the market now. If you have updated software with the serial number 13.x.x, it may happen that the activation using the Walk feature will not work now. It will be necessary to activate/deactivate the tuning using the combination of buttons - + - + or + - + -.
And so what's the top speed you csn actually get the bikes up to once Installed?
@@andysims8823 Hi.
We have experience with e-bikes with a Bosch motor at speeds above 50 km/h (for a short time), the sustainable speed on a flat surface is around 40 km/h. However, for engines with the Smart system, we recommend not to exceed an average cruising speed of 35 km/h to prevent the risk of tuning detection.
@@SpeedBoxTuning also, any idea on how to srop the rattling coming from the engine on a 2023 Sam2 6.8..
@@andysims8823 We can't advise here. We recommend contacting the e-bike dealer.
Thank you for your understanding.
Bonjour, j' ai eu énormément de mal a le monter sur un moustache game.(très peu de place entre le cadre et le moteur pour le simulateur rim magnet) et pourtant je suis très bricoleur, mais j' ai quand même réussi.
Maintenant le problème en a peut près 400 km j'ai eu 4 détection de manipulation donc 3fois bloqué 90 minutes et maintenant il se débloque plus 😢.
Comment je fait maintenant ?
Bonne journée.
Malheureusement, vous avez rencontré l'erreur 524001. Pouvez-vous s'il vous plaît contacter notre support www.speedbox-tuning.fr ou écrire un message sur FB ou IG ?
Merci
I do not recommend this !! After speaking to an agent and confirming it would work without an issue I bought one . Now the bike is telling me error 504 !! GREAT !!! Now it needs to go in the shop to resolved issue, who will pay for this ??! The bike is currently in limp mode !!! Useless. DO NOT BUY SPEEDBOX
Hi.
We are sorry to hear that you have had tuning detection. With the SpeedBox for Bosch, we recommend following some recommendations to eliminate the risk of tuning detection (524001). All manufacturers have these recommendations. You can find them, for example, with individual products on our website www.speedbox-tuning.com/for-bosch. In case of questions, we recommend contacting our support on these pages or via Messenger or Instagram.
Thank you for your understanding and many happy miles.
This is because you use flow app and do updates on your bike dont update bike and dont use flow app
nayc
Tried for hours with the positioning of the rim magnet simulator and have no success at all. Am I missing something?
Good day.
What exactly is the model name of your e-bike?
Try to pick up the signal like this: set the derailleur to middle gear. When searching for a signal, turn the crank, not the rear wheel.
Here www.speedbox-tuning.com/p/speedbox-1-2-for-bosch#1914 you will find all product and installation information.
If you don't know what to do, contact our support at speedbox-tuning.com or Messenger or IG.
Focus Jam2 8.8.
Tried installing as per instructions and still receive no info on the kiox screen
@@fwaygostjf1988 Are you sure you have a magnet on the valve of the rear wheel?
@@SpeedBoxTuning yes. The original setup has a magnet on the valve. The instructions for the SpeedBox say to remove this magnet. And replace with the sensor and spoke magnet
Hey did it on my focus jam2 6.8 not working good why
Hello.
Can you please describe a little more how the SpeedBox (doesn't) work in your e-bike?
Thank you.
The signal from the rim simulator keeps getting lost every time because I have to take it outside my frame is not like in your video. Even when it does work, the error occurs again when I push human power into the pedals. I spent 7 hours trying yesterday, and today, I'm giving it another shot. I think I might have found the solution by fixing the speed sensor and securing the simulator strong in place. Hopefully, it will work better now.
@@BenjiBenji989 With e-bikes with a rim magnet, you have to patiently search for the signal of the magnet simulator. We recommend having the transmission set somewhere in the middle range. When testing the speed sensor signal, do not turn the rear wheel by hand, but turn the crank by hand. This should help in finding the signal.
If you are unable to install the chip today, please contact our support at speedbox-tuning.com. Thanks.
It worked well
@@BenjiBenji989how you placed right the signal simulator?
If it doesn’t work, do you accept return and refund ?
Hello.
If the product is not mechanically damaged and is defective in terms of software, you have the right to a complaint and exchange or refund.
Thank you I will buy it
Hi, I received the speedbox 1.2 tuning version. The only strange thing is that when I accelerate hard, the speed exceeds 25 km per hour on the "flow app" counter and therefore the engine stops for a second. Then, still on the flow up application, the speed automatically drops below 25 km per hour and the engine comes back into action. The problem with this is that when I accelerate up to 35 km per hour, there is always a moment where I have the engine cut out for a second or two. Do you think this is normal?
@@olivoliv7769 Hello.
Yes, it is possible. Based on our experience, we recommend this: do not use the Flow App while riding. If you are already using it, please turn off automatic updates and positioning (so that your speed is not detectable through GPS) and do not make changes to the settings in the Flow App (do not modify the speed limit, torque and riding modes).
@@SpeedBoxTuning Thank you for this feedback, I will try it. in the Flow application I have the following informative message: Magnetic field of the rim magnet too weak. but this does not block the use of the bike. is this message normal? THANKS
Der Chip funktioniert nicht egal was wir machen
Alguien lo tiene instalado y le va bien?????
The max speed of this speedbox is only 35?
that kinda sucks especialy since this one is twice the price
Hello. No, the max speed is unlimited. The default max speed is 35 km/h, you can change it in settings. We recommend this speed to avoid risk of errors 🙂🤝
@@e-mike9776 Hello.
Right now, we would recommend to uninstall the chip and pedal on the e-bike for about 90 minutes. (You don't have to ride the whole 90 minutes at once, the ride can be intermittent).
Once the error is gone, you should make a few more calm rides without the chip (to get some new and clear data in the e-bike), only after that you should install the chip again. Do not ride only in Turbo mode during those calm rides, better to engage Tour, Eco, etc.
@@e-mike9776 I’ve got that bike it does not work in it
@@e-mike9776 don’t waste your money the software in the motor is too advanced for the chip
@@Joeyriot473 if that is the case, then this will be my last emtb ever....
Any1 kno if this works with grand Canyon On 7 ?
Hi. The SpeedBox 1.2 for Bosch is compatible with your e-bike. We recommend thoroughly watching the installation video and being patient when searching for the magnetic coil signal.
@@SpeedBoxTuningthank you !
@@onmyway111 I have the same bike and am thinking the same thing, how is it working for you?
❤
Le développement de l'infrastructur routière de biciclette sociologiquement de chaque ville au Maroc merci
Hello, what is technically the difference between the Rim Magnet and the normal Magnet? They have the same function and get one signal per turn if the magnet is passing, right? I am engineer and would like to understand why you need to use different speedboxes for this.
Hello.
In simple terms, a speed sensor with a common magnet works in such a way that each rotation of the rear wheel is captured by the sensor as one pulse. The number of pulses in time and the diameter of the wheel gives the speed, ODO etc. The magnet on the rim is wireless and uses the electromagnetic field from the electric motor.
The advantage of the rim magnet is the ability to read riding data directly from the electric motor (more precise data). And it also makes installing the tuning more complicated 🙂
@@SpeedBoxTuning Thanks for answering. And what is the difficulty to show the real speed with the rim version like 23,5 for 35 km/h? What I understand is that you simulate the movement of the rim magnet with an electric coil, the motor is reading the movement of the magnetic field directly without additional sensor like the speed sensor.
@@philipp6440 You are welcome 😊This is a different problem. The Bosch Smart System uses secure communication that we cannot "hack".
Price
Hi. Please visit our website speedbox-tuning.com
Thank you.
I have try to connect lights to my motor but it's need to be activated by Bosch service. Will this speed sensor work if socket is not activate?
Hello. The light socket may not be active. However, the SpeedBox does not plug into the light socket.
У меня блоканул движок от speedbox 1.1
Доброе утро.
Код ошибки 524001 - это обнаружение настройки производителем двигателя Bosch.
К сожалению, обнаружение тюнинга - неприятность, с которой приходится сталкиваться всем производителям тюнинга.
Чтобы вам не пришлось посещать велосервис и платить за разблокировку, мы рекомендуем следующий порядок действий:
Удалите SpeedBox из движка.
Ездите на электровелосипеде без посторонней помощи около 90 минут, иногда достаточно меньше. Не обязательно сразу ехать, можно прервать езду.
Как только ассистент двигателя снова заработает, проедьте не менее 10 км, переключите передачи и режимы ассистента. Это перезагрузит систему.
Затем вы можете переустановить SpeedBox.
Вот рекомендации по предотвращению обнаружения настройки:
Мы рекомендуем не обновлять прошивку вашего электронного велосипеда. Обновление увеличивает риск обнаружения настройки.
Отключите автоматические обновления в настройках потока Ebike.
Гарантия не распространяется на неисправность продукта, вызванную обновлением двигателя.
При кратковременной остановке рекомендуем держать одну ногу на педали, чтобы не запустился счетчик пробега.
При остановке на более длительный период пропустите хотя бы частичный дополнительный километраж.
Не снимайте дисплей, чтобы заблокировать электровелосипед, пока не пройдут оставшиеся километры.
Активацию/деактивацию настройки всегда следует выполнять во время остановки, а не во время движения.
Мы рекомендуем не превышать рекомендуемую максимальную скорость 35 км/ч.
This is not working at all on my bike just keeps saying error
Hello.
When did the error appear? While driving or during installation? If error 503 appeared, it means a weak magnetic field. It will help to either turn the ebike off and on, or move the magnet and try the signal again and then turn off, turn on. We also recommend turning with the crank, not the rear wheel. If you are not sure, please contact our support at speedbox-tuning.com.
Thank you.
@@SpeedBoxTuning done all of that still not working it says error as soon as you start riding it just doesn’t work you’ve made a faulty product
@@Joeyriot473 Installing tuning for ebikes with Smart System and rim magnet is a bit complicated. Could you please contact our support with the specific problem and type of your ebike so that we can find a common solution? Thank you.
@@SpeedBoxTuning already done that tried everything I promise you it’s simply not working it’s a Bosch motor
Estoy igual que tú no hay nada que hacer me sale el error ponga donde lo ponga , ya mismo lo devuelvo
After reading all theese bad comment I won't buy anymore. Too much error
Before buying an e-bike, it is good to think about whether I want to unlock the speed limiter or not. If so, it is better to get an e-bike with a simpler system. The Smart System with a magnet on the rear wheel rim is not that complicated in itself, but some e-bike manufacturers have mounted the electric motor in such a way that the installation of the tuning can be a bit more complicated.
Is good better for chi6
How Software you u have? Tell me pls your Bosch engine update Software number
The last working version of the bike FW is 10.x.x (components except motor), and 9.13.0 (motor).
@@SpeedBoxTuning my current version is 9.13.0
@@SpeedBoxTuning It says on the internet that the Speedbox 1.2 no longer works from version 9.13.0, and I have already bought the box and now it doesn't work. The Speedbox 1.2 cannot be updated either, what is the solution? I need solutions!
@@ulasdemiroglu2518 Hello.
SpeedBox does not work since version 11.13.0. If you have a lower version of the software, we recommend not updating. Ideally, turn off updates in the Flow App.
However, we should have an updated product available next week.
We recommend that you then contact your distributor for a replacement.
@@SpeedBoxTuning yes, but my dealer won't take this part back and I'm left with the costs. The part cost me $399 and doesn't even work. Speedbox doesn't care either.
Hi guys, Is this the only solution for ebike with rim magnet?thanks in advance!
Hello.
Yes, since the electromagnetic field needs to be simulated, this is the only possible way at the moment.
@SpeedBoxTuning hello.I just bought the kit for my ebike, can i put the speed sensor at the cranks side , or it won't work?
@@lekatr6815 Hello.
We don't know exactly what you mean. Place the magnet simulator in the center of the motor. And place the speed sensor on the side where there is no chain so as not to damage the speed sensor.
Hello guys, how do we check the countdown in a bike without the display? Is it necessary to do it after every ride?
@@lekatr6815 Hello.
If you don't have a display, you just have to let the countdown run until the e-bike turns off. After a long drive, the countdown can last up to 10 minutes.
😀
Breaking the limit...breaking the law.
😂
Breaking the law, breaking the law!
Breaking the law, breaking the law!
Price please....
Hello. Please check our web www.speedbox-tuning.com/for-bosch
400 Euro XD
Annoying music.
other wise ok
Telugu
In deutsch bitte
Auf deutsch bittr
Rs kati ch❤❤ malai
Not working on my bike. @speedbox help please. I have the new speedbox 1.2b and the CX Raceline. See no speed output on the kiox screen, even though it registers speed on the app. Even when I turn on the speedbox its shows no output on the kiox. Please contact me. Regards, Ghulam. Ps: I sent you an email.
Hello Gulam.
Did you send an email to info@speedbox-tuning.com?
Or you can contact us via chat at speedbox-tuning.com
Thanks
@@SpeedBoxTuning contacted you via your website, I'll send an email now.
No Good for flooded from country Philippines