2020 CX9, I need replace ambient temperature sensor where located behind the front grille , Do I need move front bumper or I can go through from gap of grille ? Thank you
You can try it but I don’t do it that way because I can’t see what I’m doing. It’s easier for me to remove it and do what I need to do. Takes me less then 20 mins to do all that. Give it a try.
If it attached to the bumper it might be hard to do that unless it’s broken. Look at the new grill and see it uses clips or screws to keep it attached to the bumper if any.
Thank for the video! I was doing my CX-9 and find out that I don’t have connected 8 pin (2x 4) connector behind front bumper, on front right side (passenger side) of the car. Do you know what is this responsible for?
Makes it easier, unless you just break the chrome pieces off. It might be attached with a clip or screws. Unclip half the bumper and try to get your hand back there to remove it. If you have the new parts, open it and see if it has any screw holes in them. For this vehicle it’s been a while so I don’t remember unless I look at it.
I have a 2021 cx9 and the front camera has a chip in it, the one under the Mazda emblem. I was quoted 3500. That’s insane . Is it possible to change out the marra
I hit a dog with my 21 CX 9. It only damaged the bottom of the front driver’s side bottom bumper by the fog light. It dented inward and cracked it. Is the bumper one whole piece with the grill assembly or can I purchase just the lower segment below the grill?
It’s usually held on to the bumper with clips or screws. You can try but you might be there till Christmas trying to get it off as opposed to taking less than 10 minutes and removing the bumper.
Hey man, I have a question. Yesterday, some guy bumped into my Mazda CX9 while he was trying to park his car. He was driving very slowly backwards and there is absolutely no scratch visible. The only thing that was out of place was the front bumper (left side) that slightly was misaligned after the bump. He pushed the bumper with his hand and the bumper sits fine again. Do you think everything is good or are there any sensors or clips that might have been damaged?
Thank you for this video! One question - if I need to replace the little lip portion of the grill above the Mazda symbol ("upper grille molding" I think it's called), how would I remove the little screws/clips that are holding that to the grille assembly? For reference, the clip I'm talking about is the little tiny one just to the right of the clip you are pointing to at 0:25.
@@j-flow617 I'm working on the upper painted nosing attached to the grill assembly...I have removed the push clips & rivets but don't see any other fasteners holding it on. is it pressure fit after that or are there more clips on the back side that are hidden?
Good video. Question: would the Signature grill work in a Grand Touring if need be replaced? Reason I ask is because I love how the Signature grill has that led light feature whereas GT doesn't. Thanks!
Great job on this so that we know where everything is! As someone who has done this on a 2021 CX-5 (to put the carbon edition chrome strip on) I'll caution everyone (fog lights or not) to remove the wire harnesses or the blocks that they attached to first, before removing the bumper. Mazda is unforgiving with how tight those wiring harnesses are and it would be easy to damage the connectors.
Thanks for this video! I had to change the lower molding on the driver's side(TK48-50-7K1A) and your video helped a lot. I ended up breaking a couple clips in the fender trim, but I was planning to changing it anyways due some deep scratch in the plastic.
Yes I have, if I come across a Mazda like this model again I’ll be sure to make a door handle removal and installation video for my viewers. Thanks for watching!
Great video. It seems most people are here for the grill upgrade or replacement. What brought me here is the front fender constantly coming loose due to a broken retainer clip. My wife and I have 2016 and 2018 CX-9's, and the passenger side front fender is popping out on both of them. We thought that was really odd and started speculating as to what the cause could be. First we thought it was possibly a known issue with the model, THEN we thought maybe it was the Phoenix heat (this past summer being the hottest on record). Anyway, the next day I pulled up next to similar year Mazda CX-9 on their passenger side, and what do you think I saw... yup, their front passenger fender panel was popped out! Now to be fair I have noticed a lot of cars having this issue in Phoenix, even newer cars, so I don't know if Mazda is actually to blame. Retainer clips seem to not like 120° weather. In hindsight, we never had this problem in SoCal, so it's probably mostly the heat, and I'd say it's likely that for whatever reason, the front passenger retainer clip is weaker than it's counterpart on the driver's side. Did this help anyone? Who knows. But ranting about it was cathartic 😂
You might be able to loosen the top of the bumper and pull it back some and stick your hand in there. If that doesn’t work try to loosen half of bumper and see if you can access the horn that way. If that doesn’t work for you then take the bumper off and it will be much quicker to replace it that way.
Thanks! Question, I have a cracked head light lens cover (the assembly and light works fine)... Is it possible to replace only the lens cover? 2023 CX-9
So I have a 2019 signature and decided to get 2022 signature grille however the led relay doesn't connect to light up grille, it fits but the wiring is diff..anyone tried that yet?
Thanks for the video, very helpful. Question: One of my front parking sensor is broken, I suppose I need to remove the front bumper completely to replace it? Do you think the sensor wires will make the entire removal process harder and risker?
Try loosen up maybe half the bumper and get it from there. If you have to remove the sensor wires too, remove the bumper if not you’ll be there until Christmas trying to figure it out.
@@j-flow617 I did. They all try to get over. Go in to replace the grill and they want to replace bumpers and everything else. No clips are broken or anything. That’s why I seen your video to try to do it myself
No I run into people that say we’re getting over on them EVERYDAY and it’s annoying because you don’t understand how the job needs to get done the right way to look good. Just go through insurance and let they pay for it or pay out of pocket. But remember you get what you pay for. I’m sorry 🤷🏻♂️
Had to replace part of the chrome grill surround and this video helped me locate all the screws and clips. Thanks for the help!
No problem, I’m glad my video was able to help you!
Did you have to remove the whole grille to replace that lower chrome molding piece? I’m going to have to fix mine
any idea why both spotlights wont turn on? would it be wise to pull out the front bumper to check for lose sensor cables?
2020 CX9, I need replace ambient temperature sensor where located behind the front grille , Do I need move front bumper or I can go through from gap of grille ? Thank you
You can try it but I don’t do it that way because I can’t see what I’m doing. It’s easier for me to remove it and do what I need to do. Takes me less then 20 mins to do all that. Give it a try.
Hi boss I got the 2023 model how can I change the front day lights to clear
hey buddy, how do you go about removing the painted mini hood trim portion thats on top of the assembly you removed?
Great video, my question is ! It's possible just remove grill parts? I have damage fron grill, silver moldings and top of the grill !
If it attached to the bumper it might be hard to do that unless it’s broken. Look at the new grill and see it uses clips or screws to keep it attached to the bumper if any.
Hi thanks for your video.. one question I need to replace the chrome grill/bumper guard on the left side.. can I know how this can be done
Is there any way to get the chrome trim off without taking the whole bumber off?
Rip it off
@J-Flow617 🤣🤣 just don't break tabs right? Lmao
I am on the same boat . What to do with those ugly silver lines on the grill.
Thank for the video! I was doing my CX-9 and find out that I don’t have connected 8 pin (2x 4) connector behind front bumper, on front right side (passenger side) of the car. Do you know what is this responsible for?
Do you have to remove the whole bumper to replace the chrome accents around the grille?
Makes it easier, unless you just break the chrome pieces off. It might be attached with a clip or screws. Unclip half the bumper and try to get your hand back there to remove it. If you have the new parts, open it and see if it has any screw holes in them. For this vehicle it’s been a while so I don’t remember unless I look at it.
I am debating if those silver lines on the grill come out by just pulling them out . i cant stand the look on those 5 silver lines lol
I have a 2021 cx9 and the front camera has a chip in it, the one under the Mazda emblem. I was quoted 3500. That’s insane . Is it possible to change out the marra
*camera
Parts and labor will do that to you.
I hit a dog with my 21 CX 9. It only damaged the bottom of the front driver’s side bottom bumper by the fog light. It dented inward and cracked it. Is the bumper one whole piece with the grill assembly or can I purchase just the lower segment below the grill?
No everything is separate pieces. Look up a diagram for your front bumper cover and find what parts you need before you purchase anything.
What if you just need to replace the matte black plastic bottom trim of the bumper? Does that bottom trim piece come off separately?
It’s usually held on to the bumper with clips or screws. You can try but you might be there till Christmas trying to get it off as opposed to taking less than 10 minutes and removing the bumper.
Hey man, I have a question. Yesterday, some guy bumped into my Mazda CX9 while he was trying to park his car. He was driving very slowly backwards and there is absolutely no scratch visible. The only thing that was out of place was the front bumper (left side) that slightly was misaligned after the bump. He pushed the bumper with his hand and the bumper sits fine again. Do you think everything is good or are there any sensors or clips that might have been damaged?
It should be fine.
Thank you for this video! One question - if I need to replace the little lip portion of the grill above the Mazda symbol ("upper grille molding" I think it's called), how would I remove the little screws/clips that are holding that to the grille assembly? For reference, the clip I'm talking about is the little tiny one just to the right of the clip you are pointing to at 0:25.
Push the center of the clip and remove with a clip remover. Tuck it underneath the clip and pry it up.
@@j-flow617 thank you!!!
@@j-flow617 I'm working on the upper painted nosing attached to the grill assembly...I have removed the push clips & rivets but don't see any other fasteners holding it on. is it pressure fit after that or are there more clips on the back side that are hidden?
@@scotts7141 trying to do the same thing! To replace that upper molding part did you have to take down the whole front grill? Thanks for the reply
Good video. Question: would the Signature grill work in a Grand Touring if need be replaced? Reason I ask is because I love how the Signature grill has that led light feature whereas GT doesn't. Thanks!
I’m not sure because I haven’t tried it. If it’s the same style it might work but I’m not sure
Great job on this so that we know where everything is! As someone who has done this on a 2021 CX-5 (to put the carbon edition chrome strip on) I'll caution everyone (fog lights or not) to remove the wire harnesses or the blocks that they attached to first, before removing the bumper. Mazda is unforgiving with how tight those wiring harnesses are and it would be easy to damage the connectors.
Thanks I had to do a grill replacement and this helped me immensely
Glad I could help!
Thanks for this video! I had to change the lower molding on the driver's side(TK48-50-7K1A) and your video helped a lot. I ended up breaking a couple clips in the fender trim, but I was planning to changing it anyways due some deep scratch in the plastic.
Me too! Mine didn’t just peel back like his
Glad it helped. You can get a bag of clips on Amazon.
@@j-flow617 not those kinds of clips. The clip hanger that connects to the back of the molding 😳
@@christierobinson6437 call the parts department at the dealership or check your local parts store and ask them
Have you done a door handle removal and installation before on one of these?
Yes I have, if I come across a Mazda like this model again I’ll be sure to make a door handle removal and installation video for my viewers. Thanks for watching!
Thanks!
No problem, glad to help!
Great video. It seems most people are here for the grill upgrade or replacement. What brought me here is the front fender constantly coming loose due to a broken retainer clip. My wife and I have 2016 and 2018 CX-9's, and the passenger side front fender is popping out on both of them. We thought that was really odd and started speculating as to what the cause could be. First we thought it was possibly a known issue with the model, THEN we thought maybe it was the Phoenix heat (this past summer being the hottest on record). Anyway, the next day I pulled up next to similar year Mazda CX-9 on their passenger side, and what do you think I saw... yup, their front passenger fender panel was popped out! Now to be fair I have noticed a lot of cars having this issue in Phoenix, even newer cars, so I don't know if Mazda is actually to blame. Retainer clips seem to not like 120° weather. In hindsight, we never had this problem in SoCal, so it's probably mostly the heat, and I'd say it's likely that for whatever reason, the front passenger retainer clip is weaker than it's counterpart on the driver's side. Did this help anyone? Who knows. But ranting about it was cathartic 😂
Interesting! 🤣
I have this problem too! I’m so glad you mentioned this. How much did you have to take apart in order to fix it? And what exactly did you have to fix?
Brother, I need to replace my Mazda cx 9 2020 horn. Do I still have to open the bumper or there is other easy way.
You might be able to loosen the top of the bumper and pull it back some and stick your hand in there. If that doesn’t work try to loosen half of bumper and see if you can access the horn that way. If that doesn’t work for you then take the bumper off and it will be much quicker to replace it that way.
can I replace lower chrome trim without remove the whole bumper
You can try but I don’t think so. It might be held on with clips or screws.
@@j-flow617 what if I chrome wrapped it . Is it look good like oem?
@@howtoacademy8725 sure I don’t see why not
I wish u make video about these chrome vinyl wrapped one da😀y
Thanks! Question, I have a cracked head light lens cover (the assembly and light works fine)... Is it possible to replace only the lens cover? 2023 CX-9
You can but it’s a pain in the butt to do, most people just replace it. I usually don’t waste my time doing it. That’s just me.
So I have a 2019 signature and decided to get 2022 signature grille however the led relay doesn't connect to light up grille, it fits but the wiring is diff..anyone tried that yet?
Thanks for the video, very helpful. Question: One of my front parking sensor is broken, I suppose I need to remove the front bumper completely to replace it? Do you think the sensor wires will make the entire removal process harder and risker?
Try loosen up maybe half the bumper and get it from there. If you have to remove the sensor wires too, remove the bumper if not you’ll be there until Christmas trying to figure it out.
How about the bumper of Mazda cx 9(2016
Whao....nice weldone job.... is it same way to replace a broken front grille for 2023 cx9 too?
same concept. the newer model might have more clips or screws. I haven't done it yet.
@@j-flow617 i appreciate your response...
Then, how to install it back?😅
How do i access the boost pressure sensor bro.. let me know thanks
Google it bro, this is a front bumper removal video.
Great Video, Does the front bumper have to be removed to replace front headlight assembly ?
makes it easier and you'll save a lot of time. Try it and let me know how it goes.
Great video! Can I remove the grill without removing the entire bumper?
no
Great! I have an CX5, I think it is very similar the process, thank you so much.
Yes pretty much! Glad to help
Thanks for the video, it was a big help
Glad it helped!
i need to replace my grill.. the wife hit a deer.. where you work out of?
Just look around your area for a local bodyshop or a local dealership.
@@j-flow617 I did. They all try to get over. Go in to replace the grill and they want to replace bumpers and everything else. No clips are broken or anything. That’s why I seen your video to try to do it myself
No I run into people that say we’re getting over on them EVERYDAY and it’s annoying because you don’t understand how the job needs to get done the right way to look good. Just go through insurance and let they pay for it or pay out of pocket. But remember you get what you pay for. I’m sorry 🤷🏻♂️
Muy bien. Me ayudo mucho tu video. Haz ganado un suscriptor
Good video!
Glad you enjoyed it!
Thx dude
Any time