You can do this much easier. Fix the pipe to your bench. Put a pipe with the same OD aside, then scratch a line by holding a ruler across the pipes and move it along the pipes. Ready! Quick and easy and no measurement errors.
Clamp pipe or bar stock in vise rub a bit of chalk on the top of the item. Place level across the top of the item drag the level through the chalk in a level position and the clean line that you made through the chalk is top dead center, takes but 30 seconds.
Sure . I have informed couple of friends. Technical piping is like a quick sneek peek place. Where a creative person can visualise the realistic site experience. Mail me at jayanjd2013@Gmail.com
I would probably put the square on top of the pipe letting the "handle" part touch the side of the pipe and using the spirit level to get it horizontal. Then just use the scale on the square to mark the spot.
if the "handle" part is long enough (could be short for larger od pipes ), can also put spirit level on the side of the pipe and measure center of the pipe
Put a mark on the pipe using the square when level put the square on the other side of the pipe and do the same thing marking the same spot and the just split the difference. It take less than a minute.
If its the first branch the center is anywhere you put it... think about it... no matter where you put a hole, that can be the center. There is no off center on your first branch.. too much left or right, just turn the pipe in that respective direction and boom! Center.
This person takes the time to put a video together and all the fitter extraordinaires are compelled to give them a hard time. Where's your videos Scooter?
I have no training in plumbing whatsoever but I think it would be easier to simply trace the radius of the pipe on a paper, then fold the paper half horizontally & half vertically then use the paper as a template making sure you clamp the pipe firmly on the floor so it does not move. With the template, you can easilly find any degre angle of the pipe. After all why complicate the process?
Get rid of the square just use the level against the pipe in the vertical position measure half the diameter from the level to the top of 4" then mark or use a center finder
Just use a paint pen draw a line perpendicular with the pipe where you would like it the pipe to intersect then use a level and put it across the pipe perpendicular slide it across the pipe and now you have an intersecting point that is dead center
HI, I"m a new subscriber. I think this is a clear presentation and very interactive, can you tell me how you make this kind of presentation? What software did you use ? Thanks
Unless there was a seam and let's say the seam was supposed to be at 136 degrees so you find your seam location and measure back to zero then center it.
Too complicated for a simple task. Just measure the OD of the pipe, wrap the pipe with a strip of paper and make the markings of pi*0D/4. You can make center hole, 90 hole, opposite hole with one shot. Done!
![[시사스페셜] 11월 17일 정운갑 앵커의 클로징](http://i.ytimg.com/vi/HnoemrP_1x4/mqdefault.jpg)
![เปิด อาณาจักร หมื่นล้าน "สาระตั้ม" l [Nickynachat]](http://i.ytimg.com/vi/3XE0nPF4YkQ/mqdefault.jpg)
You can do this much easier. Fix the pipe to your bench. Put a pipe with the same OD aside, then scratch a line by holding a ruler across the pipes and move it along the pipes. Ready! Quick and easy and no measurement errors.
Clamp pipe or bar stock in vise rub a bit of chalk on the top of the item. Place level across the top of the item drag the level through the chalk in a level position and the clean line that you made through the chalk is top dead center, takes but 30 seconds.
Esta información que le entregan al mundo es de gran utilidad para el trabajo se les agradece de corazón que Dios los bendiga
Gracias
Ah kiss my vertical crack. First vid I saw showing this was easy, fast, and a real person.
Techical piping helps in assisting new people like me in learning smart working procedure
its our goal.
welcome ......share to all
Sure . I have informed couple of friends. Technical piping is like a quick sneek peek place. Where a creative person can visualise the realistic site experience. Mail me at jayanjd2013@Gmail.com
Very good, very nice 👍, good technici
I would probably put the square on top of the pipe letting the "handle" part touch the side of the pipe and using the spirit level to get it horizontal. Then just use the scale on the square to mark the spot.
if the "handle" part is long enough (could be short for larger od pipes ), can also put spirit level on the side of the pipe and measure center of the pipe
true sounds very good yea
f
I agree with you it’s fast and accurate
Put a mark on the pipe using the square when level put the square on the other side of the pipe and do the same thing marking the same spot and the just split the difference. It take less than a minute.
Very nice
Or just use a "center finder" (that's what they are made for).
Thank u very much...excellent voice and clearity of understanding. Thanks once again
If its the first branch the center is anywhere you put it... think about it... no matter where you put a hole, that can be the center. There is no off center on your first branch.. too much left or right, just turn the pipe in that respective direction and boom! Center.
Unless the pipe is fixed in place
This is for special needs class get pipe centre finder quicker and easier if your working on large pipe
Good i love it.It is technical
This person takes the time to put a video together and all the fitter extraordinaires are compelled to give them a hard time. Where's your videos Scooter?
?
@@TECHNICALPIPING Thanks for the videos. I was addressing the critics.
You saved me thanks !!!!
You're welcome!
Superrrrrrrrrrrrrrrrrrrrrrrr
I have no training in plumbing whatsoever but I think it would be easier to simply trace the radius of the pipe on a paper, then fold the paper half horizontally & half vertically then use the paper as a template making sure you clamp the pipe firmly on the floor so it does not move. With the template, you can easilly find any degre angle of the pipe. After all why complicate the process?
nonsense, punch anywhere and thats the center of pipe. when finished putting the intersecting pipe install with that pointing upward at 90 °.
this method used for to find center with out using center finder tool.
thanks . its realy great page,, i like it
+Zain Hashmi welcome.share to all.
Very good video
Get rid of the square just use the level against the pipe in the vertical position measure half the diameter from the level to the top of 4" then mark or use a center finder
Put the level in place of the square and measure off that
if you are going for the top or side of the pipe... just use a plumb bob... where it touches... center of pipe.
20 inch ka elbow center
4 inch pipe- plumb bob will not work.
Thank you sir.
good
Pipe wizard center punch. Thats it.
The right tool is called a centre finder
This method also can find the center ,without center finder tool.
Nice
That was like reading Chinese instructions only read to me by a bot with Pommy accent.
Just use a paint pen draw a line perpendicular with the pipe where you would like it the pipe to intersect then use a level and put it across the pipe perpendicular slide it across the pipe and now you have an intersecting point that is dead center
Ok. Buen. Video. Excelente. Explicación. Como. Saber. El. Centro de. Una. Tuberia
+Rogelio Ramos Gracias
the center is where the water is at, right?
Nice trik
Tankyou🇩🇿🌷💫🕶
thank you somuch.
جيد وعمل ممتاز
Why use the square? Just hold the level on the side..
Any decent pipe fitter welder would just know how to centre that branch by eye, without going to all that trouble
Started out in Imperial, ended up in metric, WTH!
Google: Centering head pipe marker
nice
Scratch spirit level horizontaly to pipe.
😮😮😮❤❤❤🙏🙏🙏
HI, I"m a new subscriber. I think this is a clear presentation and very interactive, can you tell me how you make this kind of presentation? What software did you use ? Thanks
Simply made in power point...
@@TECHNICALPIPING by use of animation in power point
How do you find the center of a pipe? Look in the middle. Ha. I got nuthin'...
hi mr.s.smith,this method used for to find center with out using center finder tool.
Hello,
I think that 4 inch = 101.6 mm ?
outer diameter =114mm
Technical Piping
In your video tutorial at 02:07 you mentioned that 4 inch = 114 mm, however 1 inch = 25.4 mm therefore 4"= 101.6 mm.
So winging it isn't an option??
А для чего это нужно?
По сути в любой точке сделай отметку и будет тебе центр.
Just buy a V square end of.
Just need a level center, only one tool 10 sec.
hi mr.jorge
if level center not available?
a centering head is easier
everything is a center right..
Here we don't need to find the centre ...we can directly mark...because it's cylindrical any point you take would be the centre from one corner..
Unless there was a seam and let's say the seam was supposed to be at 136 degrees so you find your seam location and measure back to zero then center it.
Sir can you please Explain how to draw on on the pipe middle they video are complex
Use a center finder
Too complicated for a simple task. Just measure the OD of the pipe, wrap the pipe with a strip of paper and make the markings of pi*0D/4. You can make center hole, 90 hole, opposite hole with one shot. Done!
How did I find myself here? I was just watching Larry King interviewing Bill Shatner.
Or just use the level as the square. It works vertical too ya know lol
Why do you sounds like a robot?
.
Ada ukuran ada pengukurnya
This is an engineering video don't use music
Thanks for watching...Noted your comment.
Oh the graphics trauma!
I fell asleep. I miss something.
?
الترجمة إلى العربية
How tedious!
Buy a pips wizard
Totally irrelevant
?
This is so stupid...
Ha ha.then how to you find center?
this method used for to find center with out using center finder tool.