Automatic PWM soft start LED Dimmer

Automatic PWM soft start LED Dimmer. Soft Start Stop sunrise and sunset automatic dimmer
www.plumladen.com
The device is designed to carry Soft-Start / Stop LEDs and simulate dawn of time: 1, 2, 5, 30 seconds and 1, 5, 30, 60 minutes.
Automatic dimmer up- and down fading
LEDs with series resistor: "An automatic LED Lamp Module" to work directly with LED strips and other LED lamps in the configuration. The system can also be set-point signal, drivers and power supplies for high power LEDs, as long as these systems allows dimming input (usually as a PWM / release / DIM). The increase in brightness in the range of 0-100%, 0.025%, or a resolution of 4000 steps (~ 12bit). The device uses algorithms correction and interpolation to the characteristics of the PWM LED corresponding brightening of the perception of the human eye. The device makes it possible to initiate the process of brightening / dimming via an external start-stop button or other trigger -Signalspannung 3 .. 36V. Maybe you want to achieve full automation, instead of the release button must put daily the relay with timer.
"An automatic LED dimmer module" a transistor output type "open drain" to allow direct control of the receiver with a maximum load current of 5A (60 / 120W at a voltage of 12 / 24V DC).
Time Fade In / Out Board is configured with jumpers. The device can be directly after the
To operate switching voltage and then is only brighten possible.
If the device is operated even in standby mode, a soft start and stop, it is possible.
With this module, the sunrise and sunset can simulate.
Dimensions [mm]]: 32x36x4
Operating temperature: -40 ° C 60
Power supply: 12-24V DC
All times brighter / darker: 0.5, 1, 2, 5 seconds, or 1, 30, 60, 90 minutes (user configurable)
Output Type: Transistor "open drain".
Complementary PWM output: Yes (inverse)
PWM TTL: Yes
PWM frequency: 1 kHz
PWM resolution: 4000 steps (12 bit)
Power consumption in standby and operation: 7 mA (0.08 W at 12 V)
Maximum Output Power: 60W at 12V or 120W at 24V Imax = 5A

[@bitsurfer0101]

Do you need to use a LED driver with the board? or can it be used by itself? I don't have that many LED's to drive.

[@derguteste2202]

Hey.
Lässt sich der Dimmer auch zwischen die Leseleuchte im Auto anschließen, so dass diese beim öffnen und schließen der Türen Soft startet bzw Soft dimmt?

[@christopholejnik5972]

Das ist super genial !
Ich suche für meine Kumiko laterne sowas ,da ist eine led birne für 220Volt und 5 watt .Ich hätte sehr gerne das sie in 10 sec.oder 30sec. Langsam aufleuchtet und beim ausmachen langsam ausgeht. Kennen sie mir da weiter helfen wo ich sowas beckommen kann oder ob jemand mir sowas bastelln kann ich zahle auch gut dafür. Danke

[@pdr.servicecenter]

Hi how can I contacted wth 2 LED ?

[@nicolabaronchelli5811]

Hi, can I use 24v led strip?
Thanks

[@Plumladen]

Hi, yes 12 or 24 Volt.

[@DeepakKumar-cy8bz]

Could we light 12 v led blub with this circuit

[@MrGadgetVideo]

If it is dimmable I think there is no problem

[@ulfmusskacken]

wieso auch immer nicht einfach Jumper benutzt wurden..
ups hab gesehen, dass es jetzt DIP Schalter gibt. so gehts natürlich auch

[@Plumladen]

Ab jetzt NEUE preis :) www.plumladen.com/de/elektronik/softstart-und-softstop-dimmer-modul-fuer-led-detail.html

[@DeepakKumar-cy8bz]

I want this in india

[@herbertjanssen6172]

Scheiß nervige Musik. Warum ????