2 things first raising the hood helps speed up taping and time not to mention somewhere to rest the drill, Second a step was missing the headlight polishing to hydrate and seal the lens? And give extra clarity and shine, I don't recommend the wipes, I prefer Meguiars clearcoat with added UV protection! One coat it drys fast and you still have enough left over for a least two more sets of headlights, As a novice not bad!!🤔🇬🇧👍
Good job! My question: if you had swirl marks when done, do you think they were visible after final sanding? They say it should still be "hazy".. Mine is,but not perfectly even haze. Sounds almost impossible to get even haze.🙄
If you get swirl marks at the end of sanding this means your pressing to hard!!! Only the lightest pressure is required? Plus you don't get a cloged up disk!!!🤔🇬🇧👍
@@keithroberts5611 🤣🤣 I've done my method on 6 cars different makes and it's worked. Clear coat 🤣🤪 unless some DIY Idiot has put that on it's not an issue, because that's not what manufacturers put on their headlights 🙄
![⭐ฮิตในTikTok!! ( มะมะมะหมูเด้ง MooDeng ) Ver. แดนซ์ ReMix BY [ ดีเจกิต รีมิกซ์ ]](http://i.ytimg.com/vi/4noyAoMa7bQ/mqdefault.jpg)
![[Gegagedigedagedago] NEW Help Gegagedigedagedago Nugget escape from Nikocado Avocado Challenge](http://i.ytimg.com/vi/hJWnwRC2Fz8/mqdefault.jpg)
Man those 3m wipes are like magic. It's amazing what a difference this $15 kit can make.
Thank you for the video! Really easy to understand what result I can get with my car :)
Nice job on the vid. I'm heading out to do mine now.
Thx for the video. Very helpful!
It works well my head lights where melted it brought them somewhat back
2 things first raising the hood helps speed up taping and time not to mention somewhere to rest the drill, Second a step was missing the headlight polishing to hydrate and seal the lens? And give extra clarity and shine, I don't recommend the wipes, I prefer Meguiars clearcoat with added UV protection! One coat it drys fast and you still have enough left over for a least two more sets of headlights, As a novice not bad!!🤔🇬🇧👍
Good job! My question: if you had swirl marks when done, do you think they were visible after final sanding? They say it should still be "hazy".. Mine is,but not perfectly even haze. Sounds almost impossible to get even haze.🙄
Make sure you don;t have build up of material in the sandpaper disks, that might be causing it to make it a little hazier than it should.
If you get swirl marks at the end of sanding this means your pressing to hard!!! Only the lightest pressure is required? Plus you don't get a cloged up disk!!!🤔🇬🇧👍
I would of pop the hood instead of tape it
To be honest these kits are a waste of your time . T cut and polish brings 99% of headlights up like new and takes a fraction of the time !
Try removing old baked on Clearcoat, Then you'll find out how important sanding disk are T cut alone is useless!!!🤔🤣
@@keithroberts5611 🤣🤣 I've done my method on 6 cars different makes and it's worked. Clear coat 🤣🤪 unless some DIY Idiot has put that on it's not an issue, because that's not what manufacturers put on their headlights 🙄
@@stuartwilliams8663Nonsense all car manufacturers use a clearcoat on new headlights (fact)🤔
@@keithroberts5611 🤔🤣🤣 yeah right 🤣🤣🤣