My favorite youtuber, can't wait for your next video. And btw thank you brother for posting your last 3090 video, I am about to fix a 3090 with similar issues as yours thanks to your bytes diagram :) Peace
Cheers and thanks! Really enjoying your videos, already learned so much from you. Could you please make a video abot how RTX series cards use "Enable" signals and logical gates to start the different voltage rails? (5V, 1.8V, vCore, vMEM, PEX)
And to think. I just figured out the same thing about the memory addresses. (A1 =0x0..8, A0=0x0..2 both= 0x0..a) Then I heard about this video just hours after picking one wrong chip out of 4 possibilities. Still all the same errors after replacing the 2 bad chips, though. Guess it's gpu solderballs that are the issue. Or traces themselves. Maybe I'll check the datalines in diode mode.
Do you offer repairs for a price? I have a Zotac 3090 with temperamental black screen issues. Sometimes I can put a full load on it for hours and hours. Other times, it will not display a video signal at all.
Your videos are so informative ! I wonder how its possible to place those memories on rework station without falling off those solder balls?does the flux only holds them or some mild heat needed before doing that.
30 Prozent, von solchen Karten -das ist: "Und sie meint mich nicht! Es färbt!" Die Antwort ist in 100 Prozent der Fälle: " Warum übertakten Sie sie überhaupt?" Benutzer wollen viel auf einmal. Aber der Geist ist dabei klein und nicht immer.😒
hello! thanks for your videos, I have a 3090 that when I do a stress test it gives me a black screen, kernel error in windows. but if i reboot it works again. I am from Uruguay and here there are no people specialized in graphics cards, and watching your videos I am almost convinced that it was the change of pads that I put in 2mm.
I had a Fan Bearing Failure on my EVGA 3090ti FTW,the card overheated. I replaced all 3 fans on the card and now when the Card is under load it will go to black screen between 20 mins to 1 hour
@@KrisFixGermany right sir, but if we are running 2 Nvidia cards on the same pc. (1 we are using for display and 2 which is not giving display. so, is there any different way to allocate that riser slot (when we lspci)
The heat sink design basically just blows hot air against the motherboard and has nowhere to go I’d guess. Very common to have bulged or bad caps on motherboard between slots as well from heat as well.
![Gigabyte RTX 3090 Gaming OC graphics card Repair [Not Detected] #nvidia #gpurepair](http://i.ytimg.com/vi/QhyL1EyP4bQ/mqdefault.jpg)
I can't wait to binge your videos now that I found this channel, so glad another gpu diagnostic channel is here!
My favorite youtuber, can't wait for your next video. And btw thank you brother for posting your last 3090 video, I am about to fix a 3090 with similar issues as yours thanks to your bytes diagram :)
Peace
Cheers and thanks! Really enjoying your videos, already learned so much from you.
Could you please make a video abot how RTX series cards use "Enable" signals and logical gates to start the different voltage rails? (5V, 1.8V, vCore, vMEM, PEX)
Wow, you are super professional--- my deep respect!
Best Repair video ever! Thanks!
im amazed by these videos, keep posting more. how did you start learning on how to repair gpus?
And to think. I just figured out the same thing about the memory addresses. (A1 =0x0..8, A0=0x0..2 both= 0x0..a) Then I heard about this video just hours after picking one wrong chip out of 4 possibilities.
Still all the same errors after replacing the 2 bad chips, though. Guess it's gpu solderballs that are the issue. Or traces themselves. Maybe I'll check the datalines in diode mode.
Do you offer repairs for a price? I have a Zotac 3090 with temperamental black screen issues. Sometimes I can put a full load on it for hours and hours. Other times, it will not display a video signal at all.
Your videos are so informative ! I wonder how its possible to place those memories on rework station without falling off those solder balls?does the flux only holds them or some mild heat needed before doing that.
Привет. Отличная работа ;) Надеюсь скоро и ко мне начнут попадать подобные карты:)
30 Prozent, von solchen Karten -das ist: "Und sie meint mich nicht! Es färbt!" Die Antwort ist in 100 Prozent der Fälle: " Warum übertakten Sie sie überhaupt?" Benutzer wollen viel auf einmal. Aber der Geist ist dabei klein und nicht immer.😒
Very informative and good music.
Always nice Video my friend 👍
great video)))
hello! thanks for your videos, I have a 3090 that when I do a stress test it gives me a black screen, kernel error in windows. but if i reboot it works again. I am from Uruguay and here there are no people specialized in graphics cards, and watching your videos I am almost convinced that it was the change of pads that I put in 2mm.
Probably Vram issue. You can check the links in the video description to contact us.
Good Good Thanks
Is it possible to send in a 3090 card and have it fixed? How does pricing work?
Hello, nice videos, keep'em coming. Just by curiosity, how much a repair like this will cost?
Hello, you can check the prices in our website
I like long video repair
my left ear.. I thought I was having a stroke.
Customer gonna be happy, bet he now gonna take good care of the card... plz dont drop it again :D
А что за модель IR -станции?
Wds 620
@@KrisFixGermany some coat 1500 some 17000 USD.
Which one is real ?
Thermopro wird auch Ohne Automotisierung gehen, aber wir haben Griffe😊😊😊
NV_PFB_FBPA_FALCON_MONITOR = 0xdeaddead was somewhat indicative of how this particual card feels :)
I had a Fan Bearing Failure on my EVGA 3090ti FTW,the card overheated.
I replaced all 3 fans on the card and now when the Card is under load it will go to black screen between 20 mins to 1 hour
My 3090 black screens at the start of games. Any idea?
Hi, need you help for rtx 3090 evga fan speed rpm 0% to 100%
how to initiate mats test on the secondary card.
./mods gputest.js -skip_rm_state_init
./mats -n 1 -e 5 (5mb for example)
@@KrisFixGermany right sir, but if we are running 2 Nvidia cards on the same pc. (1 we are using for display and 2 which is not giving display. so, is there any different way to allocate that riser slot (when we lspci)
Always good idea to use MB with integrated graphics
Again the bottom vram?
This is a really bad design from nvidia.
The heat sink design basically just blows hot air against the motherboard and has nowhere to go I’d guess. Very common to have bulged or bad caps on motherboard between slots as well from heat as well.
Nope. It is because of the big and heavy heatsink and thet ram is between the gpu mounting screws and the pcie slot.
sorry i don't understand Mafiaya at all :l