Thanks for the video, very well made. The nut on the back that you tightened with a 3/8" driver: how do you adjust it or do you just run it down until a small part of the threads are sticking out (so the nylock is grabbing?)
I have a 36 volt crown sit down lift. The contactors only work on one out of two drive motors. I have voltage but the contactors still do not close. Its not the coils they seem to be ok. Plus it would be strange for two coils {fwd/rev} two go bad at the same time on the the same drive motor.
hi i am a 1 time owner op out to work from heavy lift world.. now trying to branch out..just my luck found a nice running lift 79 clark got it home move a few things around and then massive leak started from the main lift cylinder its a lark c 30 i can't even find a book on how to even try to fix ...thin i was told after i had bought a seal kit from cal lift in ca... it would be like performing brain surgery.. now i scared to try and tackle this. before i jump in would have have any vids on the subject ..i have pic iic you want to see... ty
the forklift stop moving front and back the repair company replace contacts and a coil work for one day next day back with the same , any idea what would it be ?
You have the bottom black plastic guide on the wrong way, it has 2 tip guides on it. Anyone carrying out any work like this please disconnect the battery and remove Rings or watches as when they short out they turn into mini bar heaters on your fingers or wrist. Please if your not 100% sure what your doing don't touch. Call the service department.
Very informative video! Could you show how to change the hydraulic motor brushes
Thanks
Can you please get better lighting so we can see what you're doing also. Thank you
Very nice
Thanks for the video, very well made. The nut on the back that you tightened with a 3/8" driver: how do you adjust it or do you just run it down until a small part of the threads are sticking out (so the nylock is grabbing?)
Where can I buy those parts?
Could you do a video of an electric pallet jack from crown. It won't go up or down.
I have a 36 volt crown sit down lift. The contactors only work on one out of two drive motors. I have voltage but the contactors still do not close. Its not the coils they seem to be ok. Plus it would be strange for two coils {fwd/rev} two go bad at the same time on the the same drive motor.
Una imagen más amplia del sistema
The lower capture plate is on upside down. good job security as the contacts will wear out faster.
hi i am a 1 time owner op out to work from heavy lift world.. now trying to branch out..just my luck found a nice running lift 79 clark got it home move a few things around and then massive leak started from the main lift cylinder its a lark c 30 i can't even find a book on how to even try to fix ...thin i was told after i had bought a seal kit from cal lift in ca... it would be like performing brain surgery.. now i scared to try and tackle this. before i jump in would have have any vids on the subject ..i have pic iic you want to see... ty
the forklift stop moving front and back the repair company replace contacts and a coil work for one day next day back with the same , any idea what would it be ?
Good
I have a forklift sometimes work sometimes doesn't work I have no idea what wrong with it
working on a yale warehouse lift. type E series three wheel setup. mast will not raise. is that a fuse type circuit? where are fuses located?
How about jungheinrich forklift? I'm wait your videos
I have same problem 😭😭
You have the bottom black plastic guide on the wrong way, it has 2 tip guides on it. Anyone carrying out any work like this please disconnect the battery and remove
Rings or watches as when they short out they turn into mini bar heaters on your fingers or wrist. Please if your not 100% sure what your doing don't touch. Call the service department.
Would you know how to fix a code E115 on a Raymond walkie, please let me know, I can pay for your advise via PayPal… thank you..
advanceforkliftparts.com does not exist.