BMW R1250GS Replace Windshield Bracket

แชร์
ฝัง
  • เผยแพร่เมื่อ 27 พ.ย. 2024

ความคิดเห็น • 36

  • @57Adventures
    @57Adventures 6 หลายเดือนก่อน +1

    Seriously could NOT have done this without you. Filing down the right side T25 bolt is genius. Thank you!!

    • @PacMoto
      @PacMoto  6 หลายเดือนก่อน +1

      Hey I appreciate the feedback! I get lucky and come up with a good idea every once in a while :).

  • @JSRengifo
    @JSRengifo 3 หลายเดือนก่อน

    Hello! Thank you for this video! Helped out greatly!

    • @PacMoto
      @PacMoto  3 หลายเดือนก่อน

      Awesome. Thanks for the feedback.

  • @Simon-fm8yc
    @Simon-fm8yc ปีที่แล้ว

    Glad I found this.
    I was losing my rag and about to break that side cover.
    Good video and helped me replace the same broken bracket.
    Thanks

    • @PacMoto
      @PacMoto  ปีที่แล้ว

      That’s great to hear. Thanks!

  • @givemeanaxe
    @givemeanaxe 5 หลายเดือนก่อน

    So, completed my repair this morning. Taking the right side guide rail off is actually a lot simpler than it seems. No filing necessary. Just used a small pair of needle nose vise grips, and using hand pressure only (not locking them) to hold the upper machine screw, broke the tension loose on the lower then unscrewed the guide from the top screw with my fingers. Slid it down, took the broken bracket off, installed the new one and put it back together. All together about 10 minutes of work from the first to last screw turn. But probably could do it faster.

    • @PacMoto
      @PacMoto  5 หลายเดือนก่อน

      Great job! The other side is where I needed to file down the screw head to get a wrench on it.

    • @givemeanaxe
      @givemeanaxe 5 หลายเดือนก่อน

      @@PacMoto were talking about the same side, the side with the actual crank on it.
      The throttle side.
      Starboard for all the navy folks.
      House left for thos of us in the audience
      Stage right if the rider was an actor
      The "proper right" for medical illustrators.
      The Dexter if the bike was heraldry

    • @PacMoto
      @PacMoto  5 หลายเดือนก่อน

      @givemeanaxe Best reply ever! How did you manage to get it without filing down the top nut?

    • @givemeanaxe
      @givemeanaxe 5 หลายเดือนก่อน

      @@PacMoto needle nose vise grips, but i didnt click them down, i just used hand pressure.

    • @PacMoto
      @PacMoto  5 หลายเดือนก่อน

      @givemeanaxe 👍🏻

  • @meyratemmuz
    @meyratemmuz 6 หลายเดือนก่อน

    Thanks a lot, it was very helpful !❤

    • @PacMoto
      @PacMoto  6 หลายเดือนก่อน

      I’m glad it helped you.

  • @beabeababa
    @beabeababa 6 หลายเดือนก่อน

    Just adding my thanks for making this video. I thought no one could possibly have had this same problem much less made a video about it! Looks like this problem is more common than I thought. Any ideas why? Design flaw?

    • @PacMoto
      @PacMoto  6 หลายเดือนก่อน

      Seems like a design weakness. There are windshield reinforcement brackets that can be purchased.

  • @stevesgutters
    @stevesgutters หลายเดือนก่อน

    The right had side does not need filling, there are 2 bolts that are easily reachable that loosens the knob assembly to get at the top bolt

    • @PacMoto
      @PacMoto  หลายเดือนก่อน

      That’s good to know. Thanks for the feedback.

  • @AlexLima-com
    @AlexLima-com ปีที่แล้ว

    Can you tell me how did you get the screw from the right side out? I have to replace that bracket and i didn't quite understand how did you do it without removing the whole thing.

    • @PacMoto
      @PacMoto  ปีที่แล้ว

      That is clearly a bigger challenge than the other side. I think the best way is to file the screw head flat on two sides so that you can get an open-end wrench on it. When you replace the screw, buy a flat head screw in case it ever happens again. I hope that helps.

    • @AlexLima-com
      @AlexLima-com ปีที่แล้ว

      Yes it does, just need to figure out how to flatten that screw like you said.

  • @KlimBorisoff
    @KlimBorisoff ปีที่แล้ว

    I wanted to remove the TFT display, as the bolt is very inconveniently located, but I saw your video, thanks a lot for the instruction! I will try to do the same as you.

    • @PacMoto
      @PacMoto  ปีที่แล้ว

      Yeah it’s easier to file that bolt down to get a wrench on it rather than remove the TFT. Replace it with a hex head bolt in case you ever need to do it again.

  • @TerryBlanchard
    @TerryBlanchard ปีที่แล้ว

    This is exactly what I needed! Thank you!

    • @PacMoto
      @PacMoto  ปีที่แล้ว

      I’m glad it helped you out!

  • @marcfalardeau6058
    @marcfalardeau6058 11 หลายเดือนก่อน

    Sir, I own a GS 1250 and would like to change my stock windscreen to a larger GSA windscreen. Could you make a video on this? Thanks! Marc, Quebec, Canada 🇨🇦

    • @PacMoto
      @PacMoto  11 หลายเดือนก่อน +1

      Yes, I will do that. It’s quite simple - if you look at your windscreen from the inside there is a T25 screw on each side. Remove those screws and then hold the screen from the front with both hands and lift off. Don’t worry, I’ll make a video.

  • @snakyxcs
    @snakyxcs ปีที่แล้ว

    Thank you so much for the video Man!!!!❤

    • @PacMoto
      @PacMoto  ปีที่แล้ว

      You’re welcome!

  • @joachimwedler2868
    @joachimwedler2868 ปีที่แล้ว

    Thank you so much. Great help.

    • @PacMoto
      @PacMoto  ปีที่แล้ว

      I’m glad it helped you!

  • @aldvex8541
    @aldvex8541 ปีที่แล้ว

    My winscreen has a little bit of play when i push it with my hands up and down , maybe 1 cm its not stiff steady , is it normal ?

    • @PacMoto
      @PacMoto  ปีที่แล้ว

      That sounds pretty normal. Double check that the black plastic slider is not broken. This is the slider that rides up and down the stainless steel slider bar.

    • @aldvex8541
      @aldvex8541 ปีที่แล้ว

      @@PacMoto its okay thanks tho !!

  • @givemeanaxe
    @givemeanaxe 5 หลายเดือนก่อน

    "How to replace this thing" should have called it, "how do jury rig a solution to fixing this thing"
    Gee thanks man.

    • @PacMoto
      @PacMoto  5 หลายเดือนก่อน

      Haha good point!