Peugeot 1.6 e-HDI engine light on. P0031 P2425 P0102. Only one root cause. Fault finding and repair.
ฝัง
- เผยแพร่เมื่อ 1 ต.ค. 2024
- Consider to support my channel and all the hard work put into it at / lmautorepairs
Thank you
Hi
This car came to me with the engine light on.
A quick scanning showed several codes... but, in the end, only one issue causing them all...
Once again, managed to repair the faulty component, rather than replace...
Hope you enjoy the video.
Any questions or comments put them below.
Like always, thank you for watching!
![ผัวเถื่อน - ยูริ โตเกียวมิวสิค [ OFFICIAL MUSIC VIDEO ]](http://i.ytimg.com/vi/P08ORRVDGl8/mqdefault.jpg)
I like Frech people, but don't do cars please. Do wine, Food, Parfume, Clothing..But not cars
got trouble with my 208 e-hdi says engine repair needed on dash have look at my egr valve
That's a great start you don't even know what Car your fixing ,, ITS A 508!!! 😉😉😉
😅
Was kinda irrelevante... the issue was on the engine after all...
👍👍👍
Just thinking thats the same foult on my peugeot rcz.
I have a 2014 5008, intermittent same issue, ABS skid sign,, risk of ice, came on dashboard , then stop engine, 4 miles down motorway, any clues on what fault could be ,, next day and since (no issues) car running sweet.
Scan the car... the fault codes should give you a clue of what happened... could have a glitch, not common, or something that will come back to hunting you...
Perhaps water/moisture related?
👍👍👍
After watching a few of your videos to help me diagnose a fault with my Peugeot 308, I have to say I'm thoroughly impressed! I love the way you find and repair faults in the quickest and most cost efficient way possible. I just wished you lived in the Midlands somewhere so I could book my car in with you. Oh and ignore trolls like Carla Todd, the only person those comments reflect badly on is her - what a dick! I'm now subscribed so will be continuing to look out for any new content :)
😊
Thanks...
For watching, for your comment and subscription!
👍👍👍
Hi
I have a Citroen C4 1.6 HDI 2007 . Last 6 months i have problems with the injectors . Even though the injectors have been calibrated and are fine the car rattles under load. I found coincidentally that I also have an electrical problem. There is a voltage of 9.9 volts at the lights without the lights on, without the engine running with the key in the on position. When I turn off the key switch it lasts about 1 minute (as long as the BSI standby) and then stops. I think there is a problem with the COM2000 but im not sure.I found the following:
Key in the on position (without the engine running) BSM and BSI fuse measured and everything was normal except for the headlight 9.9volt.
If I switch off the key switch (standby) on the BSM F6, F7, F9, F13 and BSI F3, F4, F7 I have residual current of 0.5 volts and 9.9 on the headlights. In sleep mode after 2 minutes then everything is gone
By diagbox, i found F522 and 7155 (It appears when I turn the switch to on and disappears when the engine starts)
Have you seen anything similar?
Is there any way to check the light switch without removing the steering wheel?
I'm starting to think the injectors rattling is coming from some electrical problem in the BSI.
Any idea what it could be??
That wheel is from Mercedes
Probably...😁
👍👍👍
You can see the Mercedes star logo and numbers.
I have Mercedes, I know.
😁😁😁
Great find and thought process mate... I was thinking about a damage wire after seeing the loose loom , top work 👍👍👍👍
Thanks Igor!
👍👍👍
He breaks things as he has a reader and instead of knowing why sensors are showing a fault he just thinks its the sensors sensors let you know when something is wrong
@@carlatodd4464
What?
Do you actually read what you write?
Watch the video before make such ridiculous comments...
You don't have a clue... nothing off what you are saying makes any sense...
Don't waste your time making such pointless comments...
@@LMAutoRepairs we watching it we are thinking of making one of you with the clips we are extracting as we speak where did you learn your skills ?
greetings from the Indonesian Peugeot car repair shop
Hi
Thank you for watching!
👍👍👍
my peugout 1.6hdi has come up with fault p0401 p1459 p0100 p0299 p0409 and has more pending codes coming on it has the engine light on but runs ok
Good diag and good job Luis as always. I think u should replace this valve to fix surely the problem.
It was obvious it was a blocked egr but he had to pull apart and break things we are having a great laugh watching him bodge poor customers lol
@@carlatodd4464 jealous much
Hi L.
Thanks for another good upload!
👍👍👍
Thank you for watching!
My 308 gt line 2.0 hdi on mornings shows engine fault on the screen but no engine light or codes. 🤦🤷
EASY FIX: Replace ABS pump, fix 100%
What has the ABS pump to do with it?
You haven't watched the video... have you?
👍👍👍
@@LMAutoRepairs No, miért watcholnám meg?
Anyone know why my 2012 508 saloon boot won’t open? The electronics are not opening the boot
Someone pls help
Impossible to say what it is without any checks...
It can be many things...
Start with the basics, fuses etc...
Scanning the car, and have a look at some live data might be also quite helpful...
Otherwise, it is all pure guess work...
👍👍👍
Thanks mate I’ll probably just have someone come look at it
Hello I have same problem with same code but my car won’t start last time start normally but not not
Every time Louis is using his multimeter, I have strong urge to walk past while he is probing something under the bonnet and peal that fecking foil from the MM screen. xD
😬😊😜🤦♂️
🤣🤣🤣🤣🤣
You really made me laugh now...
Me too. I tend to raise my head, lean on one side to see better. This means that his videos are good.
@@MirceaD28
😊😉
Hi , I'm experiencing the same problem with my 508. Are in in manchester by any chance? So I can pop on your driveway/garage. Tyia
Hi
Not really... I quite far from Manchester...
👍👍👍
greeting. I have a problem, if you know what it is, I would be very grateful. at 80 c the car heats up and starts the fan in 2 speed and starts the error as soon as the fan is activated ... and there is not a single error on the computer. It is a Peugeot 508 .2012 2.0 diesel
The fan shouldn't kick at that temperature...
Check live data as during warming up...
See if anything looks odd... I never came across such fault...
👍👍👍
autel , launch etc seems to have the (cracked) PSA diag. software embedded as asks for km , etc in the same fashion. same goes for VAG and VCDS similarities.
👍👍👍
Thank you for watching and for your comment!
,
, NOT, NOT, NOT ... Peuge-NOT.
,
,
,
,
Can you come and fix my 3008, its juddering at random speeds but have no engine light or anything haha
Awesome Fix👍
Really informative video, without changing any parts, your content is awesome, you deserve more sub's
Thanks for sharing Bro👍
Slowly will get there...
Thanks!
For watching and for your comment!
Very good video again, always always always start with basic checks like fuses, power and ground etc etc. So many dealers start with throwing parts and then £800 later the panic starts as the fault still is there!
Absolutely!
Thank you for watching and for your comment!
👍👍👍👍
Nice video and help me so much.
Can you tell me, please where is MAP sensor on Peugeot Partner 1.6 HDI 2013?
Thanks
Not sure on that one...
But they usually on the intake manifold, hose or somewhere near the intercooler outlet...
Thank you for watching and for your comment!
👍👍👍
Hi thanks for the good work. I have a Peugeot 5008 with the engine light on. I bought almost half of the engine parts but nothing change. At the end, one mechanic decided to cut off the signal wire and convinced me that the problem is solved. Am now stack. I don't know if you can help. If so send me your working address please.
Hi
What was the codes or live data saying?
Thank you for watching!
man my peugeot 308 has P3060 and P0Q11 referring to fault in timing control solenoid and carbon built up in engine air intake
can you please suggest how much this would cost?
Good logical approach, but what a horrible engine, quality of components and wiring is appalling.
Was definitely not the best...
Thank you for watching and for your comment!
hi I recently found your channel, and I must say as a mechanic in the motor trade your abilities are fantastic, I don't know if your a qualified mechanic or not but I think any garage would be more than happy to have you on their team as a most valued member of staff, your diagnostic technique must surely be second to none.
As a small point about the wheel issue, I spotted that the castellated retaining cap and 'R' clip was missing off the end of the CV thread...
Thanks for your most informative videos
😊
I am just a guy playing with stuff really...
Really appreciate you comment, thanks!
👍👍👍
Luis, have you bought a work truck? I did it too and would love to see yours :)
I have it for about 4 years now... lol
You have been missing some of my videos...😔
Naughty boy...😜
Thank you for watching and for your comment!
@@LMAutoRepairs XD Ok maybe i haven't watched every video you have uploaded but i have the time now as i am in quarantine in Italy :)
@@planet1250
Ah... hope you are ok...
I will might make a video on it... once is tidy up...😬
👍👍👍
@@LMAutoRepairs All is good man, except the fact that i have no car to work on since the workshops are mostly closed... We're currently living off my savings... we'll see my friend :)
planet1250 di dove sei?
Thank you for this video...helps me get a guide to what might be faulty in my peugeot 508
☺️
👍👍👍
Old school common sense fitter' did you find the Gorilla that broke the componants ??
🤷♂️
wrong wheel... sometimes the mind goes wild thinking why and how it gets to this state, it just doesn't make any sense.
Lol
Thank you for watching!
👍👍👍
I know what you're saying about Peugeot on the MaxiSys. I've been having quite a few problems over the last 12-18 months with PAS vehicles on my MaxiSys Elite.
I've been struggling to get decent support from Autel on the topic but recently they've told me that they're completely reworking the PAS system, as they have many issues, and it's due to be completed this March but I'm not holding my breath...
Would be great if they do something about it though...🤞
Thank you for watching and for your comment!
Supervideo.. nice
☺️
👍👍👍
Hi LM, when the battery of a peugeot is replaced does it require the battery registration to be done?
Depends on the model... not all require...
👍👍👍
did peugot have relays for indicators lights behind speedometer!?
Which peugeot?
👍👍👍
@@LMAutoRepairs 207, i think it is because sounds come from there but maybe its just better to buy canbus led lights with no hyperflash then dismantling speedometer and under it to replace relay
Year?
Doubt there is any relays in the cluster... that will be just a speaker making the sound...
The indicators are most likely controlled by the BSI...
You need to scan the car to have a better understanding of what is happening...
👍👍👍
@@LMAutoRepairs i didnt see any other place with relays not under sterrring wheels or where fuses are so there could be only there or maybe behind radio /central console !! NObody on net dont show anything but i see that many dismantling alot
Most the the cars now have internal relays inside the modules... in the case of peugeot, inside the BSI... so no, you don't see the relays... some don't even have relays anymore, as everything is electronically controlled... the sound on the dash it is just a mimicking of the relay sound...
👍👍👍
Helpful repair video 👍
Thanks!
👍👍👍
Good work! Hot glue is wonderful stuff; you should consider using in future. Tried to fix a freezer compartment door with lots of diffrrent glues and epoxies and hot glue was the best, especially since the door is being opened and closed many times.
When that engine gets to operating temperature, that hot glue of yours will become as soft as epoxy resin.
He was not trying to glue anything together, it was already a snug fit, he was sealing the unit to keep water out.
As per UK Citizen...
Thank you for watching and for your comment!
👍👍👍
@@ukcitizen1158
Thanks for the reply!
👍👍👍
And for watching obviously!
Hi
I have Peugeot 3008 and i have code P0030 how resolve this problem.
Check fuses, wiring and connectors to the heater...
Test it to make sure the ecu is activating and supplying the sensor.
If all good, I would suspect a bad sensor...
👍👍👍
what IS model of your car?
and what number of fuse?
IS HS
This was not my car... all as per the video...
👍👍👍
@@LMAutoRepairs
What IS number of fuse ?
Hi mate I have problem peugeot 508 2.0 diesel 2014 years I take off flow meter it's working bad is lights check engine.if I put it back it goes very slow what's the problem?
Scan the car, and check live data...
Could be a bad air flow meter... but might not be...
Thank you for watching!
@@LMAutoRepairs I found the wrong cable connecting maf sensor colors are not correct United ... can you send some pictures if you can help me nicrusu007@mail.ru please
Immobilizer system have a separate controller in ecu
If its raining like that, you can use a cheap mobil tent and park the front of the car. Keep up the good work ;) www.monivel.hu/monivel/feltolt/termek/kep/n_324386_1.jpg
👍👍👍
Thank you for the suggestion...
For watching and for your comment!
Hi Louis, hope this words finds you well, I paused the video in 19:45 to say thank you man, it's really interesting what you sharing, thank a lot, respect 😊💪👍
😊
Thanks!
👍👍👍
Cat needs looking at 70.000 on pugs great video
Thanks!
👍👍👍
Mine happend few days after getting DPF cleaned by the garage.
if i remember right the corsa are wired the same of the one feed
Possibly...
Thank you for watching and for your comment!
Hi can you help on a 308 low circuit on egr ?
Thanks, nice video and you solved the problem, don't forget to tell the guy that the wheel will fall off soon.
😊
👍👍👍
Hope you and your family are doing ok is this strange time Luis. Good diag and fix no need for new sensor it will out last the wheel and bearing lol
Yes Ian... so far so good... difficult is to explain the girls what is going on...😔
Same fo you, take care...
Thank you for watching and for your comment!
Nice
☺️
Thanks!
👍👍👍
Thanks a lot ! You are very strong person to get to the destination of your problem solving....:)
😊
Thanks!
👍👍👍
😁 usa agua mano..ta usar saliva 😁engracado
Fantastic bro I'm doing my best to understand you because I just start learning English... God bless you I prefer you speak French 😂
Ahahah
No chance on French... lol
You will learn English before I can speak any French at all...😜
Thank you for watching and for your comment!
Just like my car :-) but I have the steering wheel on the other side :-)
🤣🤣🤣🤣
Thanks!
👍👍👍
maybe you can get that fixed :P
@@jusb1066
Turn it up side down...😜
You are the best ... Greats from Germany
😊
Thanks... for watching and for your comment!
👍👍👍
Hello,i came here for my 308,you are a genius.thank you.
☺
Thank you!
And that tire ! my lord the things people do .......................
Indeed...
Thank you for watching!
Good repair as always . I would definitely say something about the wrong sized rims as well . You have the footage and I know this video is pretty old but still . I write everything what I find wrong and is not related to the repair I am hired to do down . Let the client sign of and I am happy .
👍👍👍
Thank you for watching and for your comment, really appreciated!
Wonderful job as always thump's up!!
Thanks!
For watching and for your comment!
GREAT JOB
Thanks!
👍👍👍
Thank you, nice work as always... 👍
Thanks!
👍👍👍
quando tiveres que mexer em silicone usa ajax ou um limpa vidros e do melhor pra nao agarrar aos dedos basta borrifar bem a peca e acertar o silicone
👍👍👍
Obrigado pela dica!
Very helpufull repair and interresting method
Thanks!
👍👍👍
Hello, I have a problem with my car Peugeot 207 1.6 hdi 2011 82kw 112ps, one day I get a message Engine fault repair needed, the car loses power and the engine noise changes sharply, and the engine vibrates, and the gas does not exceed 3, then removed the battery and put it back again this problem is removed, after a month the same problem appears again, I am thankful if you help me solve this problem
Scan the car... any suggestions from me would be pure guess work...
👍👍👍
@@LMAutoRepairs
the foult code P0268
- Cylinder 3 injection circuit
-Short circuit to positive
-Permanent
@Jupa Home
Hi
Have you tried to unplug that injector, and see if the codes change to open circuit?
Have you measured that circuit at the ecu?
@@LMAutoRepairs no no i have not tried it
Today I checked the car on the computer and it showed me this code
UCE: E8
CODE P0268
DESCRIPCION: HIGH INPUT CYLINDER 3 INJECTOR CIRCUIT
Thanks Luis for this great video I like it so much . always your videos are useful
😊
Thank you very much, for watching and for your comment!
👍👍👍
Congratulations from France
😊
Merci !
👍👍👍
Good work thank for your time you r master
😊
Not quite...lol
Thank you for watching and for your comment!
😊 good job 👏 my friend 👌
Thanks!
👍👍👍
Thank you for sharing diagnose video,Hope you are happy and safe!
Hi
Yes... so far so good!
Hope are also all safe!
Thank you for watching and for your comment!
👍👍👍
@@LMAutoRepairs Welcome my friend
@@kingbolen_official
👍
Thanks good video working in rain is the worst
Yes it is... I hate it...
Lol
Thanks, for watching and for your comment!
Again a good fix rather than part swap. Could it have been done with a cheep OBD2 code reader?
Most likely yes...
Thank you for watching and for your comment!
@@LMAutoRepairs Thanks you are great at finding and repairing. And passing that on to all of us watching. It's just the very expensive scanner for DIY'er. Really enjoy watching you work.
@@johnf3278
Yes it is... but as I said, you can get cheaper, way cheaper scanner, and do the same thing... (or similar...)
I’m glad you won in the end.
😊
Thanks!
👍👍👍
Good analyting, good Video. Thanks.
Thanks!
👍👍👍
its really informative video ,
Thanks!
👍👍👍
Hi, i really admire you knowledge and most of all the way that you think.
I would like to ask you about something that you are doing. I saw that you are measuring resistance with your DVΩM with no cutting power supply to the car.
I thought that was dangerous and could harm car's systems but if you do that it's obvious that is ok :-)
What's finally the right procedure? Can i measure the resistance on a circuit which is on power or not?
Thanks for the knowledge that you share with us and keep up the EXCELLENT work
Greetings from Greece
Hi
Remember I said in the video that the ignition was off... so the circuits where not powered...
Thank you for watching and for your comment!
He is a idiot it was obvious its the egr needs cleaning I have watched a few of his dodgy repairs and all he does is use his reader and try change sensors breaking parts on the way that car will be coming back like every repair i have seen
@@carlatodd4464
🤣🤣🤣🤣🤣
No, did not came back... still going strong...
So, in your opinion, I have not yet fixed anything right on my videos, why do you carry on watching them?
🤦♂️🤦♂️🤦♂️
You really made launch with such a pointless comment...
Still, thank you for stopping by...
@@LMAutoRepairs lol you have a scanner wow learn how to use it sensors are there to let you know there is something wrong investigate why the sensor is showing a fault as this video was just a blocked egr valve I would not trust you with a bicycle
@@LMAutoRepairs you cleaned egr you must have the 3 codes all said blocked egr nothing wrong with the sensors
This guy knows his stuff 👍🏽🇬🇧
😊
Thank you...
👍👍👍
Hey is that scan tool good and what's the part number or name I know autel but which one and again you are smart love your work man
Hi
This one is the Autel Maxisys MS908P.
Thank you for watching and for your comment!
@@LMAutoRepairs any time I learn alot as being a auto electrician
1 last question does that scan tool do just about all cars and Australian cars
@@thekustomknight2264
We all do...😉
@@thekustomknight2264
Yes...
👍
Thank you Louis for the information on your channel
Thank you for watching!
👍👍👍
Thank you for another great video!!!
Thanks!
👍👍👍
In vw 1.9 tdi ecu detect function of egr through map sensor by changes of pressure in intake manifold.
speak in simpler terms, whats ur point
Thank you.
😊
👍👍👍
Awesome video, thank you!!
Thanks!
👍👍👍
Another one of your masterclass , thanks again mate.
Appreciated!
😊
Thank you for watching and for your comment!
What scan tool is this?
Hi
Maxisys MS908P...
Thank you for watching!
,good job luis thank u
Thanks!
👍👍👍
Obrigado pelo vídeo Luís, espero que estejam todos bem.
Só aventuras neste carro 🙄
Sim, por aqui estamos todos bem, obrigado...
Espero que por aí também...
👍👍👍
Good video
Thanks!
👍👍👍
another good job,
😊
👍👍👍
Mercedes rim on peugeot 😂
😊
I know... ridiculous...🤦♂️
Thank you for watching!
Super film 📼 pozdrawiam
Thanks!
👍👍👍
Excellent as always! Thanks
😊👍👍👍
Thanks!
........Good work
Thanks!
Nice bro
Thanks!
👍👍👍
Hola, en español?
Hola!
Garcias!
👍👍👍
Tambem tenho essa avaria no meu Peugeot.... Onde posso comprar essa valvula?
Na marca... ou online...
Normalmente uso o ebay...
👍👍👍
@@LMAutoRepairs peço desculpa.. só hoje vi que repondeste... como posso pesquisar no ebay?
@@perdidolx
www.ebay.co.uk
E os termos de pesquisa?? Solenoid valve??
Sim...
Thanks for the video
@LM Auto Repairs . Hi, great video. We have 2016 308 1.6 hdi. The alternator failed, so it was replaced, but the stop engine light comes up with a battery charging fault still. The alternator is charging at 14.4V though, and the car drives fine. They tried clearing the BSI and the ECU, but it keeps coming back. Any ideas, we're desperate?! Thanks
What code are you getting on the BSI and engine ecu?
Thank you for watching!
@@LMAutoRepairs I'll let you know. It went into our Peugeot dealer and they couldn't get rid of it, waste of time!
that is a first time I dislike your video because you haven't showed us how did you fix the issue
🤦♂️
You need to watch the video first...
I just did not showed what was the problem, but I definitely showed how I have repaired it...
So, not really sure what you are talking about...
🤷♂️
@@LMAutoRepairs Of course I have watched the whole video at the end but you supposed to show us where was the problem, thanks
@muhammed sons
Watch the video again then...
I showed the broken valve, I showed why the fuse was blowing and I showed how I have repaired the valve...
So, what part have I missed?