@@brandokieft9567 certainly no bad words for this guy but you are right. He didnt even center the crankshaft after putting the casings together, thats a quick method to mess up new bearings. And no squish measurement :(
@@noelwillemsen3449 just search for Original Piaggio sm06 180cc and not sito plus crap the real sm06 exhaust that are installed under the runner 180cc or italjet 180cc. They are silent and perform way better then the 125 standard exhaust
VERY GOOD JOB! WITCH TRANSMISSION DID YOU USE? THE MALOSSI ONE OR THE ORIGINAL 125 ONE? THNKS. I AM PREPARING A GILARDONI 125 TO 180.SO I NEED TO KNOW.
Can I ask you a someting? Do you have a list of all the parts you bought. I wanna do this to mine skr 😊 and if you ask, yes I have a lot of expierence 😙
1 mistake here...when you put the 2 halfs together...always tap the crankcase left and right side with a plastic hammer to remove tension from the crankcase and bearings of putting the 2 engine halfs together...and also why dont change the rear tire?! it is worn and dangerous with that speeds
Where was the torque wrench for any of the case bolts or cylinder bolt. No squish band check. I could go on as I I see quite a lot wrong with this engine build.
Grymt! Är det originalförgasare? Vilken modell/märke isåfall? Sitter också på en 125:a Skipper med mikuni vm20, som jag tänkt byta cylinder på. Skulle du säga att det är en ”rolig” skillnad? Värt det? För övrigt är jag ganska säker på att jag köpte min blå Piaggio Sfera 80cc av dig. Den är under bygge, med ny Athena cylinder!
Hi! i have a question, does the piston from the kit comes with the same size pin as the original or do you need to change the crank? Thank you for the video!
meguiars compund och polish, hård skumtrissa med compund och mjuk med polish, tänk på att gärna använda litre extra medel på plastkåpor då de inte tål värmeutvecklingen lika bra som plåt.
You can see the experience while you work. Good job. Love to see it
He did a lot of things terribly wrong tho😬
@@brandokieft9567 certainly no bad words for this guy but you are right. He didnt even center the crankshaft after putting the casings together, thats a quick method to mess up new bearings. And no squish measurement :(
@@matthijs3891 Maybe he didn't show it
9:25 skr turns into 1000cc
Nice, i have a tph 172cc build 25mm dell orto and the gilera sm06 exhaust. Autowheelie. The standard 125cc exhaust you have is not good for the 172cc
Which one did we need for 172cc (exhaust) ?
@@noelwillemsen3449 just search for Original Piaggio sm06 180cc and not sito plus crap the real sm06 exhaust that are installed under the runner 180cc or italjet 180cc. They are silent and perform way better then the 125 standard exhaust
Why is the standart exhaust not good for the 172
@@thedungeongamer8511 Simple. Why isnt an sport 50cc exhaust good for a 70cc racing.
@@thedungeongamer8511underpowered. Its made for something with less power.
Madre mia!!! Menudo faenon!!! Tienes q desmontar casi toda la moto... Menuda currada te has pegado!!
Skippers are monsters
I haven't seen one of these for years 👏🏾 great vid thank you
You are a very, very good craftsman
VERY GOOD JOB! WITCH TRANSMISSION DID YOU USE? THE MALOSSI ONE OR THE ORIGINAL 125 ONE? THNKS. I AM PREPARING A GILARDONI 125 TO 180.SO I NEED TO KNOW.
Sleeper
verkligen!
Riktig bra video! 🔥🥰
Heel netjes gedaan👏
Well done 👏👏👏👏
Nice Movi
Cooles Video 😎
Get a sm06
Bra jobbat :) den blev riktigt snygg där i slutet!
Can I ask you a someting? Do you have a list of all the parts you bought. I wanna do this to mine skr 😊 and if you ask, yes I have a lot of expierence 😙
welldone!!!
What carb did you install??????? stock?????
Meraviglioso!...wonderful! Where r u from?
Why when the egine is cold the scooter has more power then when its warm?
Looks better without the rack on the back.
en dan met versleten achterband ,, rrijde
Do you also have video's while you are driving it ?
very nice how to fix mine like that
Nice video but you forgot to balance the crancase.
And he whacked the bearing in the case with a hammer🤦🏻♂️
This skipper malossi block can be setup in piaggio gilera sp180..??
Die Lagern sollten nicht erhitzt werden sondern nur der Lager sitzt
Die Lagern müssen kalt sein
Hallo, welchen Vergaser hast du denn verbaut???
Beste Grüße Matze
Che suono...
1 mistake here...when you put the 2 halfs together...always tap the crankcase left and right side with a plastic hammer to remove tension from the crankcase and bearings of putting the 2 engine halfs together...and also why dont change the rear tire?! it is worn and dangerous with that speeds
Where was the torque wrench for any of the case bolts or cylinder bolt. No squish band check. I could go on as I I see quite a lot wrong with this engine build.
Grymt! Är det originalförgasare? Vilken modell/märke isåfall?
Sitter också på en 125:a Skipper med mikuni vm20, som jag tänkt byta cylinder på. Skulle du säga att det är en ”rolig” skillnad? Värt det?
För övrigt är jag ganska säker på att jag köpte min blå Piaggio Sfera 80cc av dig. Den är under bygge, med ny Athena cylinder!
2 questions. What kind of motor is this? Is it similar in mounting to the gy6?
Piaggio 125cc 2 stroke
No idea if the mounting is any different
Is it good in fuel gas?
Depends on how u drive it
What parts do you need I have a paiggio skipper st 125 2001
Ich habe die gleiche und noch 5 weitere davon in anderen Farben.
😍😍😍👍👍👍👍👍👍👍
hi can I put a 150 engine set on a piaggio skiper 180 engine?
Hätte Interesse an dem selben Service
✊✍️
Exhaust origine 125 ?
Which battery you buy
How do i know which 1 is 2 stroke and which 1 is 4 stroke? There are 2 types right
Its the sound 2stroke its toef toef toef like a chainsaw and 4stroke like someone shitting himself
It is 2 stroke right?
What model for the block mallosi
Carburator?
Testrun ????
How long did the bulid take?
Kan du fixa min moppe, den startar inte
Hi! i have a question, does the piston from the kit comes with the same size pin as the original or do you need to change the crank?
Thank you for the video!
Also did you keep the same carb? bigger jets?
U can use The standaard crank it has a bigger piston then 125cc and i reccomend u using a bigger jet and keep The original 20,5mm carb
Fet build men måste erkänna att det är den fulaste scootern
Kommer det videos med betan?
vill ni det?
@@snabbmoppe klart!
Vad använder du för vax medel?
meguiars compund och polish, hård skumtrissa med compund och mjuk med polish, tänk på att gärna använda litre extra medel på plastkåpor då de inte tål värmeutvecklingen lika bra som plåt.
jobbar du med detta eller är det em hobby
hobby, pluggar atm
@@snabbmoppe ok, gött me extra cash
@@Erik-fd2jw som student hjälper det :)
Translate in dutch please
Fet video
tack!
Bad sound quality