I'm an experienced quad builder and that was very well done. You must work in the video industry or have a lot of experience doing this. Hats of to this excellent build and flight. I enjoy flying my Cinerace20 quite a bit. Running more powerful motors 1303 5000kV. I think Flywoo is having great success with this release lots of good buzz around how well it flys for something so small.
Thank you! Yes I do photography and videography for my job, so this video is just for fun. Thanks for the kind comments, Im still pretty new to fpv. Yeah Flywoo makes really really fun products to fly. I also have their firefly babyquad 1.6" and also explorer. They all really make sense for some reason and at least one of them are with me every flight session! Not only fun, but most likely also with its portability! They fit in the bag easily haha just throw it in there!
for me it was a relaxation video and at the end it was exciting to watch that it flies well! I really enjoyed it! 🙂 Excellent skills of building, flying and editing!! Well done! 👍
Hi! No, actually in the beginning, it doesn't actually matter. BUT, I usually like to solder each wires direct because it just looks cleaner. (I give the wires a little twist too before bolting down the motor, especially for cinewhoops so its nice and tight against the top of the ducts. Just some extra info: Please keep in mind even though you soldered direct or crossed, you will need to always check/adjust your preferred motor direction in bl_heli and betaflight (with props off) and change settings from there. What I like to do is put a thin piece of coloured tape on the tip of the each of the motors and film them in slow motion using my phone to see which ones are rotating the wrong direction. Another way to reverse motor direction is re-solder that specific motor crossed and it will rotate the other way! Cheers.
Nice video I just have one question, which pad did you solder the LED lights to on the flight controller. Was it a 5 volt 8 volt 12 volt pad just curious.
I believe it was 12v! Here is the product page for more.details. It comes with a BEC and switch so you can turn it on and off. flywoo.net/collections/cr20-part/products/1pcs-dc12v-flexible-cob-led-strip-4mm-x-1m
Hello Sir I have build this drone bit its not lifting up and when I change flying mode it's not arming please help me out I am exhausted completely trying different things
Hi did you go into betaflight and set your modes such as arm, beeper, angle, turtle and ensure your remote controller is set exactly the same? To check, Props off, plug in battery to quad, plug into betaflight and turn on your remote controller. go into modes tab. click your buttons and Make sure it matches with the modes you created.
Hi yes you need 12v. Flywoo sells a 12v bec with switch, or another version (v2) that can communicate to betaflight by transmitter switch. Flywoo led strip usually comes with the bec
@@PattyFlipzis it okay if i direct conect it to battery pad? i bought used frame,it comes with ledstrip and litle thing to switch it on / off. its that the bec?
I recommend to use the switch. After that I forgot where the switch solders to. I might show it in my old cinerace build video.. please check and good luck
Video Mistake Log & Suggestions: ***I mounted the props wrong - Do not copy or your quad will do a funky flip! (mount prop side with 2 circular depressions, make sure they are visible on the screw side) Correct picture here (reverse prop direction shown) drive.google.com/file/d/1xKo4hb1SN-6eFbFBA15YQq0dO8veF64a/view?usp=sharing ***TBS nano RX should have been attached behind the 3d print that also holds the 2 antennas out back, for now I just stuffed it to the inside of a duct instead of leaving it beside the top plate like in my video. ***Antenna holder was designed to hold a smaller antenna such as a TBS minimortal T, I stuffed a TBS Immortal T V2, but realized it would pop out from time to time, I added zip ties so it stays in place. (not shown in the video)
I'm not 100% sure, but I think you installed the propellers upside down. The "prettier" side of the propeller with one dot should face the motor, while the "uglier" side with injection marks should face down. Check it out and maybe your performance will increase.
Hi yes I did but didnt re-shoot the footage 🤣. I did write it somewhere in my super long description that I made that mistake. hehe Thanks for watching! 😃
@@alexandrughita5891 Hi, don't follow my video to mount the propellers, its wrong. Please do reverse prop direction in betaflight. The 2 circular indention Markings on the prop should be facing you when screwing down the propellers. Look at my correct image here for reference: drive.google.com/file/d/1xKo4hb1SN-6eFbFBA15YQq0dO8veF64a/view?usp=sharing
hello Sir I really need your help I need your quad's default configuration for my flywoo I somehow messedup with default setting now its not going well please send the configuration file.
@@PattyFlipz Thank you very much for the quick reply settings problem resolved but one problem I am facing that I am using R9 MX ota Rx and QX7 tx both are binded and registered correctly but not communicating please help me to resolve this issue I have soldered Sbus out to rx pad
@@naveensingh2491 R9 and R9MM must be on the same firmware. R9MM needs to solder F.Port to any TX UART pad and enable Serial in Port Configuration tab in Betaflight. Go to Receiver tab, choose Serial then choose F.Port
Hi Chris Newby! Thank you for visiting! This video is only intended to give you just an "idea" on what it takes to build a FPV drone. It is not a step by step tutorial. Cheers and positive vibes to you. Hope you find what you are looking for. If you have any questions on the build just let me know. I'd be happy to answer.
I'm an experienced quad builder and that was very well done. You must work in the video industry or have a lot of experience doing this. Hats of to this excellent build and flight. I enjoy flying my Cinerace20 quite a bit. Running more powerful motors 1303 5000kV. I think Flywoo is having great success with this release lots of good buzz around how well it flys for something so small.
Thank you! Yes I do photography and videography for my job, so this video is just for fun. Thanks for the kind comments, Im still pretty new to fpv. Yeah Flywoo makes really really fun products to fly. I also have their firefly babyquad 1.6" and also explorer. They all really make sense for some reason and at least one of them are with me every flight session! Not only fun, but most likely also with its portability! They fit in the bag easily haha just throw it in there!
Awesome!!!!!
I love to build.
Love the bird commentary. Nice touch.
Yeah man! Buildings awesome!!! Especially when it flies! Best hobby ever. Let's keep on building!! XD
Great sound track with the breeze blowing,lol.
hahaha! nice and calm video except behind the scenes I'm swearing every couple minutes with these finicky screws and wires
for me it was a relaxation video and at the end it was exciting to watch that it flies well! I really enjoyed it! 🙂 Excellent skills of building, flying and editing!! Well done! 👍
Thank you so much. I am glad you enjoyed it 😍🤩
Very nice my man! Love watching drone builds like this
Thanks man!!
amazing build video!
Love the detail, the sound, all around. really bliss!
Thank you!! Glad you enjoyed it!!
really great build log! this channel needs more subs!
Thank you so much!! :D
❤ Awesome 🎉🎉🎉🙏🙏🙏
Thx bro!
Great video
Thank you!
Amazing work my friend! I've one question, soldering the motors wires requires any specific order (direct, crossed)?
Hi! No, actually in the beginning, it doesn't actually matter. BUT, I usually like to solder each wires direct because it just looks cleaner. (I give the wires a little twist too before bolting down the motor, especially for cinewhoops so its nice and tight against the top of the ducts. Just some extra info: Please keep in mind even though you soldered direct or crossed, you will need to always check/adjust your preferred motor direction in bl_heli and betaflight (with props off) and change settings from there. What I like to do is put a thin piece of coloured tape on the tip of the each of the motors and film them in slow motion using my phone to see which ones are rotating the wrong direction. Another way to reverse motor direction is re-solder that specific motor crossed and it will rotate the other way! Cheers.
Interesting. Subscribed. ❤️
10K VIEWS! Thanks Everyone. I need to make more of these build videos!!! What should I build next??? 🤣
Nice video I just have one question, which pad did you solder the LED lights to on the flight controller. Was it a 5 volt 8 volt 12 volt pad just curious.
I believe it was 12v! Here is the product page for more.details. It comes with a BEC and switch so you can turn it on and off. flywoo.net/collections/cr20-part/products/1pcs-dc12v-flexible-cob-led-strip-4mm-x-1m
Hello Sir I have build this drone bit its not lifting up and when I change flying mode it's not arming please help me out I am exhausted completely trying different things
Hi did you go into betaflight and set your modes such as arm, beeper, angle, turtle and ensure your remote controller is set exactly the same? To check, Props off, plug in battery to quad, plug into betaflight and turn on your remote controller. go into modes tab. click your buttons and Make sure it matches with the modes you created.
@@PattyFlipz yep everything is setup but now problem is the battery I want to know that how much weight it can lift
@@PattyFlipz I have 4s 1300 mah battery
@@amritafagna130 Hello! 1300 is a bit heavy for this quad. You will want something under 800 mah. 500, 650, 750, etc.
@@PattyFlipz thanks I'll order the same
my ledstrip wont turn on when conecting it to 5V pad,but when i try tro direct to power cable it turn on..
Hi yes you need 12v. Flywoo sells a 12v bec with switch, or another version (v2) that can communicate to betaflight by transmitter switch. Flywoo led strip usually comes with the bec
@@PattyFlipzis it okay if i direct conect it to battery pad? i bought used frame,it comes with ledstrip and litle thing to switch it on / off. its that the bec?
I recommend to use the switch. After that I forgot where the switch solders to. I might show it in my old cinerace build video.. please check and good luck
Video Mistake Log & Suggestions:
***I mounted the props wrong - Do not copy or your quad will do a funky flip! (mount prop side with 2 circular depressions, make sure they are visible on the screw side)
Correct picture here (reverse prop direction shown) drive.google.com/file/d/1xKo4hb1SN-6eFbFBA15YQq0dO8veF64a/view?usp=sharing
***TBS nano RX should have been attached behind the 3d print that also holds the 2 antennas out back, for now I just stuffed it to the inside of a duct instead of leaving it beside the top plate like in my video.
***Antenna holder was designed to hold a smaller antenna such as a TBS minimortal T, I stuffed a TBS Immortal T V2, but realized it would pop out from time to time, I added zip ties so it stays in place. (not shown in the video)
I'm not 100% sure, but I think you installed the propellers upside down. The "prettier" side of the propeller with one dot should face the motor, while the "uglier" side with injection marks should face down. Check it out and maybe your performance will increase.
Hi yes I did but didnt re-shoot the footage 🤣. I did write it somewhere in my super long description that I made that mistake. hehe Thanks for watching! 😃
@@PattyFlipz Hello. Could you please help me with some advice? how are the propellers mounted and what is the direction of the mottors? thanks !
@@alexandrughita5891 Hi, don't follow my video to mount the propellers, its wrong. Please do reverse prop direction in betaflight. The 2 circular indention Markings on the prop should be facing you when screwing down the propellers. Look at my correct image here for reference: drive.google.com/file/d/1xKo4hb1SN-6eFbFBA15YQq0dO8veF64a/view?usp=sharing
hello Sir I really need your help I need your quad's default configuration for my flywoo I somehow messedup with default setting now its not going well please send the configuration file.
Hope your quad is ok. Please find flywoos default factory cinerace dump here flywoo.tawk.help/category/cli/cinerace20
@@PattyFlipz thank you very much
@@PattyFlipz Thank you very much for the quick reply settings problem resolved but one problem I am facing that I am using R9 MX ota Rx and QX7 tx both are binded and registered correctly but not communicating please help me to resolve this issue I have soldered Sbus out to rx pad
@@amritafagna130 remember to flash the same Betaflight firmware to match dump file from Flywoo website. Very important.
@@naveensingh2491 R9 and R9MM must be on the same firmware.
R9MM needs to solder F.Port to any TX UART pad and enable Serial in Port Configuration tab in Betaflight.
Go to Receiver tab, choose Serial then choose F.Port
How many temperature for soldering like that? I'm usually use 250-400°C
Hi, I turn it up as hot as it can go. I believe the number is around 800+ degrees.
@@PattyFlipz whuaaa my solder iron max only 400°C hahah it's more than enough, Oke thanks for the answers
@@Mclfpv i think patty meant °F not °C. 800°F is about 426°C which is not a big difference.
Nice tutorial !
Thank you! Glad you enjoyed it!
This fc support 6s?
No I don't believe so. If you need 6s aio you can look into The Beast aio from iflight.
ah another one is mamba 722 aio 35a from diatone.
How much does it cost? Brother
The cinerace20 starts at $220 and depending if HD can be over $300
Show
✌ Thanks!
What a complete waste of time. Basically the instruction manual but worse.
Hi Chris Newby! Thank you for visiting! This video is only intended to give you just an "idea" on what it takes to build a FPV drone. It is not a step by step tutorial. Cheers and positive vibes to you. Hope you find what you are looking for. If you have any questions on the build just let me know. I'd be happy to answer.