No it ain't, you can't cheap out on those. EVERYTHING IS LITERALLY THE SAME! and it was operating error. Didn't hit the bolt release, kept yanking the charger and under lubricated I guarantee
When reloading mags from an empty mag and the bolt locked back, hit the bolt catch on the side. Much faster than racking the charging handle when reloading for a tactical reload from empty mag.
its a few issues.. dont think it has an adjustable gas block.. the short barrel is optimal for suppression in blackout... so its probably designed around suppression.. so supers are going to act unreliable.. and that shows the likely case being the malfunctions were failure to extract due to incomplete cycling. second.. hes holdint it out limp wrist like.. the action of the bolt cycles best when you have it braced against your should.. should put a brace on it. also i may be going off on a limb here, but i highly doubt he properly oiled it as well.. all factoring into the malfunctions... what is my experience regarding the issue? research task force 145.. :-) peace, love, and chicken grease.
@@ShowMe_GunzTVthe 5.56 out of any barrel below a 10.5 inches is going to lose an insane amount of velocity. Additionally, because of the barrels twist rate coupled with the extremely low velocity, the round will begin to tumble and start to keyhole targets because it is not angle to rotate enough to create the tight spin necessary to keep the bullet pointed straight in the air. It’s like when you throw a foot ball. You want a tight spin because a tight spin makes the throw more accurate. This is very bad because it extremely negatively effects the accuracy of the 556/.223. A .223 will also perform even worse than a 5.56 out of an extremely short barrel below 10.5. It’s still bad out of a 10.5, don’t get me wrong. Longer barrels always perform better with these rounds. But 10.5 can be effective out to 250 yards and provides plenty of penetration in closer ranges too while being accurate.
My brother I new to guns but I learn fast ,1 he should have know if the gun is loaded or unloaded 2 went you fire an ar with a loaded mag a round automatic loads it self so went you change mag you don’t need to re rack it ,every sec counts went contacts down range 3 do not flinch forward went pulling a trigger it should surprise you and you should know the hammer about to go off 4 good standing position good eyes and ears but all so train with out so you understand what it like without it cause shit go down with out eye and ears, over all 8 out of 10 good job keep it up
@@ShowMe_GunzTVBecause everything about this is typical. The hood boys doing weird shit on the range with guns literally as whack as the makeshift sawn off pipe guns spotted in Brazil. Just buy a normal rifle you can hit something with, a bunch of ammo and youtube whatever you can't figure out. PSA ARs are cheap as hell and do the job fine.
So I'm so confused and please help me understand, why does the urban gun community hate stocks? Do they know they'll never hit a 25 yard target with a 2inch barrel let alone no buttstock for support, is this for show? Why show off a gun if it can't hit anything? And dont say "they're having fun" because there's a difference between fun and practical.
Can't stuff it in your pants if it has a stock. Honestly I wouldn't be surprised if the guy with a regular, stocked rifle was laughed at for it in those circles.
I would’ve been embarrassed to record that bullshit. Most races have rifles to reach out distances but, a lot of us blacks want pistols for close quarters battles to fight each other. What are we as black folk going to do when those who enslaved our ancestors are shooting from 100 yards or more away and we can’t physically see them or hit them with those damn micro barrels AR and AK pistols. You gotta wait until them enemies are in a 25 to 50 yard range because anything beyond that, those little ass barrels aren’t that effective and the bullets will tumble sooner than they would than with a 16 to 20 inch barrel
Those that enslaved you are dead. Their great grand children do exist and many of them are in positions of power... but most of y'all keep voting for them.
You mean muhammad Because muhammad Enslaved black people and sold black People as Slaves But momins defend that there is no racism in islam to gain more conversions
I feel it. I shoot 170yrds with lever action 22lr 16inch barrel iron sights. But since it a 22 it barely has enough to hit a ping at that far hahah..but it's funny to see people miss and winder how I can hit with it
I’ve had nothing but problems out of 300 blackouts it’s a gimmick yea it’s got better blah blah blah it doesn’t function don’t waste your time if you want a 7.62 stick with the tried and true.
Wow. Watch some TH-cam or something man and learn how to operate and handle the thing BEFORE you go to the range. ALWAYS study up on a firearm before you purchase, shoot/operate, work on and/or clean it. Always
2nd video ive seen of yours.. back to back... you shouldnt be firing a weapon.. pick up a training course before you hurt yourself.. or worse, someone else
I’d rather throw hands than shoot that to defend myself 😂
😂😂
😂😂
😂😂😂😂 gaaaadamnn
Facts
Na fr
I lost it when the mag fell out
Same 😂.
Works better as a flamethrower, then a slug thrower.
this boy got no idea what he's doing,. take it away.
Bro u exactly right! Possible cheap ammo too 🤦🏼♂️
Yes
This is the one 😂he been watching to much TH-cam 😅
Dubble feed put more oil in. It will be nice and smooth .
Thanks for the tip
Why lie. You clearly don’t know anything either
And you're a Democrat.
That flinch lol
Take a good luck, you are seeing the future of America 😮😮😮😮
This is what Happens when you cheap out on the barrel. Bcg. Buffer. And gas system
So I’m in the process of building my first ar 15 any suggestions on those parts in particular?
@@stormlife3824 need more info. On the build your doing.
@@stormlife3824Buy PSA rifle to save money until you get a feel for what you want, spend the extra money on ammo to train with.
No it ain't, you can't cheap out on those. EVERYTHING IS LITERALLY THE SAME! and it was operating error. Didn't hit the bolt release, kept yanking the charger and under lubricated I guarantee
@@stormlife3824DO NOT buy a PSA. There is a test on yt. They're budget for a reason. Trash. Stick with aero precision
Feed Jams!!?? Malfunctions everywhere..Geezzz!!!
lol ikr his friend says "first hangup" after like the 3rd thing that went wrong... lmao just flip that POS and get a proper setup
My man’s got the reciprocating rear charger.. nice
:'D
Flip ups on backwards 😂😂😂
😂😂😂😂😂
When reloading mags from an empty mag and the bolt locked back, hit the bolt catch on the side. Much faster than racking the charging handle when reloading for a tactical reload from empty mag.
The charging handle is coming undone because the bcg is slamming back to had. Try a heavier buffer or stronger spring.
U gotta adjust ur gas system on it
How you kno that’s the issue?
@@TheLilmikeymike15 It's not the gas it's the micro buffer he has to put it together a certain way
I don’t think he has an adjustable gas block……..
@@TheLilmikeymike15could be gas or buffer. Looks like it got a cycle issue.
its a few issues.. dont think it has an adjustable gas block.. the short barrel is optimal for suppression in blackout... so its probably designed around suppression.. so supers are going to act unreliable.. and that shows the likely case being the malfunctions were failure to extract due to incomplete cycling. second.. hes holdint it out limp wrist like.. the action of the bolt cycles best when you have it braced against your should.. should put a brace on it. also i may be going off on a limb here, but i highly doubt he properly oiled it as well.. all factoring into the malfunctions... what is my experience regarding the issue? research task force 145.. :-) peace, love, and chicken grease.
You may want to pay someone to change the gas block. The gas is way too much. Are you using a .9 diameter journal instead of a standard .75?
What’s better out of 5inch barrels, 223/556, 300,762,458
.300
Really like my barrels 7” or more this one is not my build
@@ShowMe_GunzTVthe 5.56 out of any barrel below a 10.5 inches is going to lose an insane amount of velocity. Additionally, because of the barrels twist rate coupled with the extremely low velocity, the round will begin to tumble and start to keyhole targets because it is not angle to rotate enough to create the tight spin necessary to keep the bullet pointed straight in the air. It’s like when you throw a foot ball. You want a tight spin because a tight spin makes the throw more accurate. This is very bad because it extremely negatively effects the accuracy of the 556/.223. A .223 will also perform even worse than a 5.56 out of an extremely short barrel below 10.5. It’s still bad out of a 10.5, don’t get me wrong. Longer barrels always perform better with these rounds. But 10.5 can be effective out to 250 yards and provides plenty of penetration in closer ranges too while being accurate.
Them boys got switchs
This is why you practice which is what he is doing.
That buffer system does the same in mine they suck
Safety my boi 🫡
I lost it when the MAG Dropped 😅🤣🤣😱
My brother I new to guns but I learn fast ,1 he should have know if the gun is loaded or unloaded 2 went you fire an ar with a loaded mag a round automatic loads it self so went you change mag you don’t need to re rack it ,every sec counts went contacts down range 3 do not flinch forward went pulling a trigger it should surprise you and you should know the hammer about to go off 4 good standing position good eyes and ears but all so train with out so you understand what it like without it cause shit go down with out eye and ears, over all 8 out of 10 good job keep it up
Good boy 😅
Micro thaaaaaang, what?!? Gangsters thinking they hard until it's time to actually use a gun lmaoo
Koolaid jammer😂
Mine did the same thing I had to modified it for it to cycle good
Micro buffer only work for 556 or lower
Dam fr ?
@@210_inks3 nah I got updated info now g they say it work with 300 blk and 7.62 Buffertube needs adjustment
All looks no show. Lmao.
Jammerrrrrr 🤣
Bro getting smoke he get into a shoot out wit dat
Not my gun anyway you mfs speaking from the outside in got a lot to say
@@ShowMe_GunzTVBecause everything about this is typical. The hood boys doing weird shit on the range with guns literally as whack as the makeshift sawn off pipe guns spotted in Brazil.
Just buy a normal rifle you can hit something with, a bunch of ammo and youtube whatever you can't figure out. PSA ARs are cheap as hell and do the job fine.
So I'm so confused and please help me understand, why does the urban gun community hate stocks? Do they know they'll never hit a 25 yard target with a 2inch barrel let alone no buttstock for support, is this for show? Why show off a gun if it can't hit anything? And dont say "they're having fun" because there's a difference between fun and practical.
The urban community prefers to look cool over being practical.
Can't stuff it in your pants if it has a stock. Honestly I wouldn't be surprised if the guy with a regular, stocked rifle was laughed at for it in those circles.
Glad you tested it out at the range
Shit my arp runns flawless you gotta adjust the gas block and upgrade buffer internals
What size buffer do you have?
It’s the buffer tube it’s known to jam on the 7.62’s had the same problem
Get a longer buffer tube
Finally a black guy with sights
Should have went with the aero precision build cheap but not too cheap to whwrre the gun doesnt function properly this is crazy
I hate how mfs never know their gun isn’t loaded
Oil goes a long way
What brand is it?
None
Didn’t jam, he didn’t put one in the head. Then he shot it dropped mag and reloaded 😂 he’s running drills it didn’t jam.
You know very little about firearms
Yeah u would've been deceased my guy. How do people forget to switch from safte to fire before firing I don't get it.😅
put a 7.5 barrel and it will be usable
Subs or supers??
Why tho?
Flop wrist causes cycle failures
Put the brace on! Fawwk ATF
😂😂
What’s the point of buying an 300 black out that short ? Like help me here folks😂
That’s the point of 300blk. Better for short barrels. Pointless to have a 300blk without a can though.
Why not just buy a firearm that’s actually useful
Need subsonic shells bruh
556 mags don’t work with 300 blk out
yea they do
I would’ve been embarrassed to record that bullshit. Most races have rifles to reach out distances but, a lot of us blacks want pistols for close quarters battles to fight each other. What are we as black folk going to do when those who enslaved our ancestors are shooting from 100 yards or more away and we can’t physically see them or hit them with those damn micro barrels AR and AK pistols. You gotta wait until them enemies are in a 25 to 50 yard range because anything beyond that, those little ass barrels aren’t that effective and the bullets will tumble sooner than they would than with a 16 to 20 inch barrel
I’m sure he’s only got one rifle there couldn’t possibly be a way for him to have an arp and a regular ar
Those that enslaved you are dead.
Their great grand children do exist and many of them are in positions of power... but most of y'all keep voting for them.
You mean muhammad
Because muhammad Enslaved black people and sold black People as Slaves
But momins defend that there is no racism in islam to gain more conversions
Lol I gotta a 7.5 too😂
I feel it. I shoot 170yrds with lever action 22lr 16inch barrel iron sights. But since it a 22 it barely has enough to hit a ping at that far hahah..but it's funny to see people miss and winder how I can hit with it
I’ve had nothing but problems out of 300 blackouts it’s a gimmick yea it’s got better blah blah blah it doesn’t function don’t waste your time if you want a 7.62 stick with the tried and true.
Need that pistol gas tube
Bunch of milk carton models waiting to happen
Kinda look like a baby scar
Not cycling properly. I'd get a different buffer and tube
Only way this is cool is if u make it shoot slugs with a 308 lower
W oppss
Wow. Watch some TH-cam or something man and learn how to operate and handle the thing BEFORE you go to the range. ALWAYS study up on a firearm before you purchase, shoot/operate, work on and/or clean it. Always
Nah I’m good
Wtf is he doing bruh
At least you can beat someone withbit
Smoked boots 😂
Yeah pack it up
boi WTF😂😂
Try some oil
This is getting embarrassing now. With all these failing ars
Bruh y’all better just stop following these corrupt ahh atf laws and get a brace 😂 all love bro❤
Dat thang look nice
What is the actual hell is this guy doooooing lmfaoooo
Did that MF jam with every shot?
Whats the purpose...silly dangerous machine...especially in the hands of the unskilled.
Buffer tube
Mines blow smoove
Velocity has left the chat
2nd video ive seen of yours.. back to back... you shouldnt be firing a weapon.. pick up a training course before you hurt yourself.. or worse, someone else
Thanks for watching
Basketball "ARP" americans...
Outta pocket😂
Clean your bolt assembly
Its too small get a lil mo inches on ur barrel it needs sum mo weight dats all
cant afford ammo?
Can’t afford a stock or brace either.
@sector986 right because people not posting felonies means "broke" you sound dumb
Wtf? First hang up he says. Smh.
Its that micro buffer
Yessir
Learn how to use a firearm first.... THEN make youtube videos.
Why post this????
Y comment
@@ShowMe_GunzTV cause I wasted my time expecting to see some good shooting
Limpen it.
Sights are backwards
They have no idea what they are doing
Buffer tube to short
You know you didn't need to post this unimpressive video and the sights are on backwards
No targets were harmed in the making of this video
Damn
Good he not ina field wit it and only in THAT field with it
Throw the whole gun away
Buddy has no idea what he’s doing. Show him.
Cringe
Ah nah. You dead
Yeah you'd die
koolaid jammer
cringe af
😅😅