Counterbalance Forklift Training Video | How to De-stack at High Level | 4KS Forklift Training
ฝัง
- เผยแพร่เมื่อ 25 พ.ค. 2024
- In this Online Forklift Training video, our instructor demonstrates how to safely de-stack at high level using a counterbalance forklift truck. This is a common forklift truck for Novice (beginner) forklift training.
Visit 4ksforklifttrainingltd.co.uk/... for more information on the best counterbalance forklift training to book your course today or call 0121 294 9395.
Steps for Counterbalance forklift training:
► Follow the correct forklift procedure to move off; Gear, Observation, Handbrake release and final Observation (GOBO).
► Drive forward in a slow steady speed in the centre of aisle looking at the direction of travel.
► Line up front wheel axle (pivot point) to the centre of load
► Apply handbrake and full lock steering towards the load and gently accelerate, maintaining observation in all directions
► Stop 6 inches before racking, apply handbrake and transmission in neutral
► Using tilt hydraulic adjust the mass into vertical position to have the fork arms straight
► Complete all round especially above looking out for obstructions above ourselves
► Lift fork arms towards the height of the load
► Complete all round check and follow GOBO and gently drive forward in to the load
► Once into position and ready to pick up, apply handbrake and transmission into neutral
► Gently raise the fork arms to lift the load up ensuring looking above the load for any obstructions
► Follow the forklift GOBO procedure, twist body, arm behind seat looking at direction of travel and slowly creep back in reverse
► Concentrating 80% in direction of travel and 20% at the load ensuring clean exit from the racking
► Stop 6 inches away from racking and apply handbrake and transmission in neutral
► Lower the load into travelling position, 4-6 inches off the ground
► Follow GOBO procedure and twist your body posture behind the seat and full lock steering towards the direction of travel.
4KS Forklift Training Ltd provides RTITB accredited forklift truck training at both our fully approved and accredited training centres in Birmingham and Peterborough.
► View all our Forklift Training Courses: 4ksforklifttrainingltd.co.uk/...
► Forklift Refresher Course: 4ksforklifttrainingltd.co.uk/...
► Reach Truck Training: 4ksforklifttrainingltd.co.uk/...
► Bendi Flexi Forklift Training: 4ksforklifttrainingltd.co.uk/...
► LLOP PPT Training: 4ksforklifttrainingltd.co.uk/...
► Forklift Instructor Course: 4ksforklifttrainingltd.co.uk/...
To skip to a particular section of the forklift training video please see the chapters below.
► Chapters for Counterbalance forklift training:
0:00 - Counterbalance Forklift Training Video Intro
0:10 - How to de-stack at high level using a counterbalance forklift truck
0:19 - Forklift GOBO procedure to move off
0:30 - How to drive a forklift counterbalance truck
0:48 - How to turn a forklift 90 degrees safely
1:19 - How to raise forklift forks safely
2:00 - How to enter a load at high level with a forklift
2:44 - How to lift a load using a forklift
3:45 - Lowering a load with a counterbalance forklift
4:19 - How to reverse a forklift counterbalance Truck
► Follow us on Facebook: / 4ksforklift
► Follow us on Instagram: / 4ksforklifttrainingcentre
![[TH]FFWS SEA Spring 2024 Point Rush - Day 1](http://i.ytimg.com/vi/_LI5pXZFYhw/mqdefault.jpg)
Think a lot of people are missing the point of the strictness of this video compared to how fast it really is in the workplace… as the old saying goes some rules can be bent but not meant to be broken is a good way of summing it up where common sense is concerned. He’s not wrong in the video as that is proper and correct use of the equipment! You wouldn’t show someone a training vid cutting corners just because your gaffas up your arse lol. Safety is everything and it’s better to know how it’s supposed to be done in the most safest way possible even if it does look like it’s taking the Mickey
Very well explained and in depth and calm
My guy ones you lift the pallet up you tilt the fork back so it doesn't slide forward during a reverse or incase of an emergency when someone or something coming up behind you out of nowhere.
Please Note, The very First thing you should do is check for the weight of the item you plan to move and your forklifts limit. There’s different size machines in a lot of the facilities I’ve been to with different weight capacity for different lifts. ALWAYS DOUBLE CHECK.
While I've been taught to do this where I got my certificate. I have never and will never do this, you can feel when it's on the verge of being to heavy for that truck. And yes, I've had my back wheels lift up trying to lift a 2000kg pallet. But I would obviously never try to lift anything so heavy high up anyway. We hardly use racking regardless and I obviously won't stack it on top of something.
th-cam.com/video/2yWvVv39bzo/w-d-xo.html
@@msmit1999 Lifting back wheel is asking for disaster.
@@megafauna8374 you think i lift stuff like that meters high? If i only lift it 10 centimeters, the pallet will hit the ground before the forklift can even come close to tipping over.
Very clear and professional demonstration! Thanks Tony!
thank you so much i needed rerence of turning towards the pillet
Sou empilhador, aprendo muito com seus vídeos, obrigado!
A really good tutorial. Thank you.
I would be fired on the spot if it took me any longer than 2 minutes to do all of this lmao
Yea, imagine actually applying the handbrake and putting it in neutral everytime you raise or lower the forks.
Exactly
I’m telling you 😂 like always gotta break and neutral whatever he’s saying I’ll be fired bc I’m being expected to boom boom like fast lol this are for beginners and easy way to get fired
@@dunnervibz3397 yeah this way I'll take an entire day to load a trailer, and I can't even line up for the pallet as the aisle is narrow tight, I have to pull it out with one fork diagonally behind one of the pallet's blocks. It's also impossible not to turn with raised forks (often with load) as it's the only way to make the turn in the narrow aisle.
@@msmit1999 you know this guy tryna get ppl fire during the pandemic and Russia vs Ukraine war 😂
Perfect training
Nice , thank you
Good job
Thank you...👍🏾
Very good quick and simple way on lining up for a pallet, Great video👍
Nice one sir.
Good couch
We have been taught to lifting the pallet a few inches and then tilting the mast backwards. Then moving a few inches backwards, till it’s clear to lower the forks down to roughly 10 inches above the ground. Is it also a correct way to do it or not? Please do answer.
Thanks😎
Tony the Top G
This is all nice in theory, but if we had to go through all his steps, it would take us 1 whole day to unload a 30 pallet truck. And the next day we would probably be fired :)))
The average operating time for this entire process is 3-4 minutes. As a trainer myself I have kept track of times from new operators to experienced operators
To the people who are saying that he is working slow . Fool this is a training video
Good
Failed to do all round checks before changing direction 90 degree turn, failed to check underneath when raising lowering load. No mention of mass deflection at high level. And and every time he stopped whilst pulling out the load he never once looked over to his left shoulder.
What a Janet!
No observations when raising the forks or lowering the forks?
Nearly 5 minutes to take down one pallet. I’d be getting my P45 if I did this
This is a demonstration video, intended for learners.
In my 9 hours shift With this tempo I wouldn’t do 10% of the norm 😂😂😂
Yeah that's what went through my mind as well watching this video 🤣🤣🤣, if I load a truck at this speed the truckdrivers would be very happy with me....NOT! And why use the handbrake while your forklift isn't moving? You can put your foot on the brake if necessary. A lot of this video is over exaggerating!!
@@Countravendark
Its overexaggerated because people will sue a place like McDonalds for not knowing coffee is hot and win.
@@Countravendark for the sake of training yes, obviously once youre used to the controls you just get on with the job which yes means move your a*s
@@bobshanery5152 That case you quoted is quite literally the definition of dangerous practice for a business and a legitimate lawsuit for negligent practices. The coffee in the McDonalds lawsuit was over 110C when served to that woman which is far past boiling point and essentially becoming steam every few seconds. Do me a favour and boil a kettle and pour it over your legs for 5 seconds and see how that feels? Because that temperature is only 85C on average.
It seems that you are an expert already. When a first-timer trainee on a very first day, should a trainer/instructor focus on "speed" in traveling, hoovering around, turning left and right, spinning, lifting up and down, etc. in teaching???
I think the point of this video/demo is for beginners and for safety as well. like me who completely have no idea how to operate, this is very helpful.
Is that palet the wrong way round?
Never looked up before raising ur forks, also reversing out of the racking with out without a load u should be looking back but also having frequent checks to make sure the load or forks are withdrawn cleanly
he did, he levelled off the load at eye level then looked up when he raised to high level, what he didn't do is when he raised the load off the rack, he didn't do a slight stabilising tilt back when the pallet was at high level.
@dannye3325 I was taught not to tilt until the load has been lowered .It appears your comment is not best practice.
Drove a forks for nearly 30yrs, we'd be that far behind if we done all that, we'd get the run...i was trained in 3, 5 and 11 tonne forks
can we take training on visit visa
I've got an instructor that is going to fail me if I don't do all around checks when i am using the hydraulics tomorrow, yet you are not doing them? 3 times i counted. Why the lack of consistency in the training?
Good evening my name is Orlando Nathaniel please put me through about how i can get a forklift operator job i have been working as a forklift operator for over 10ysrs up till date . I want to experience working with a different company i am open for day and night shift as an added value thanks.
I will do a retraining next week. I cannot put the fork inside the pallet when im picking above eye level. Give some advise
When you first begin just take it slow Don't be anxious that will only make you mess up eventually you'll get the hang of it and it will be second nature you'll be able just to look at the pallet and know exactly how high to raise your forks. A lot of people in the beginning make the mistake of having their tilt too far back and that will cause you to mess up especially above eye level because you cannot see how far back your forks are.
Practice.
What more would you expect from a Linde operator.
shouldnt you had the tilt on back so the load is resting on the backrest when you were lowering the load to the floor?
@Elango I was told to by our instructors on the course that it was a must i dont know if its different in an lane warehouse tho.
Yes, sufficient back tilt when lowering. The lack of consistency across the education sector is infuriating.
To be fair no....nearly never a reason to tilt in the air. Mast vertical is how the trucks base lifting rating is determined, tilting back only moves the centre of gravity towards the rear of the truck. If you are reversing out responsible there is no way to make that pallet slide off of level forks.
Linde e20 badboy
Seatbelt?
I get that these are instructional videos, but on a professional level this severely hampers productivity of everyone on the workfloor. At my workplace we have a NUMBER ONE rule, which is: "When you see a forklift or reach truck doing its job, STAY AWAY. Accidents will be held liable against the person entering the vehicle's operating space."
When I drive my reach truck down the narrow aisles, I can't keep track of EVERYTHING that's going on around me because I have a quota to meet. When I have my forks up at the fifth shelve (6-7 meters up in the air) I am never allowed to remove my eyes off the load, as the goods I am handling are dangerous chemicals. The safety of the product goes above the safety of well-informed, alert employees. We also have a section in our warehouse which hermetically seals itself off in case of the fire alarm going off, trapping people inside. The only exit door can only be opened with a key and a code.
Again, I completely agree to use this footage for educational and training footage, but it's a LONG SHOT from operational reality. It's just too slow.
The grey area between training and reality.
You mean you never apply the handbrake every single time you want to use the hydraulics?!
@@mrdoogle5931 Exactly, because our forklift has an automatic brake that engages when the wheels aren't turning.
It's common sense not to drive or walk behind a forklift driver when he's working. But unfortunately, common sense isn't at all common.
Where is the pivot point ??
How to find pivot point properly?
aligne your front wheel axis with the center of the pallette/load you want to pick, whilest driving exactliy in the center of the runway
It’s usually the middles of the front tire
This is good, nice and slow until you have to load a lorry in under x amount of time and is pouring down with rain and diver tell you to get a move on …😮😅
Sir please set the seatbelt first before you startup and driving
You didn’t honk the horn.
And why does he need to do that??
Left hand sir is always on the steering wheel
I can not find a job as a forklift operator cause I taken my driving license a year ago and I never operate anything. I can operate if they add me their company but they always said you are a beginner that why we can not choose you sorry :(
You are not showing the controls and the pedals.
Limb was outside of the cab that’s a 5 point penalty
Tutorial on how to get fired 😂
Under no circumstances should your forks be tilted back beyond level without a load. That being said, once you have a load, you tilt your forks back beyond level. It's called a load rest for a reason. DIRP.
I would get fired if I took the time to do all that
no, thank you
20 mins at home depot just became 4hours
by the time he gets back with the pallet it will be time to go home.
Il est inutile de gerber au sol de basculement est impossible mais très possible en hauteur
There so many job available I don’t care about no forklift I’ll work elsewhere cuz so many job available 😂
so why are you here?
Could only watch 1 minute of that pish
Too much for your limited brain capacity I imagine..
He did not put his seatbelt!😂
Ce n est pas tout à fait vrai lorsque vous avez soulever la charge et que vous ignorez son poids qui doit être indiquer sur les cartons vous devez gerber pour que le poids que vous igno soit plus sur l arrière c est une sécurité de plus
He didnt tilt the forks before he moved the truck
He obviously tilted it before moving before video was recorded
But for training purposes he should of shown tilting the truck initially before moving
anyone who knows clarks never buys linde
Those where way to many breaks on and neutrals.
But then this is training. Not working on ⏰
Plenty of old timey gunslinger forklift cowboys here. This is a pretty good instruction video for learners on how to qualify for a license, not be a gung ho hero. Driving a forklift while operating the forks is an instant fail in most jurisdictions.
At my previous job it was regularly an issue getting 20 ft long lumber through a 16 ft wide gate. You have to have the load in the air to see and avoid obstacles finesseing through. Not being a cowboy but I like to say I've got a black belt in forklifting 😆
If you actually did this you'd be working a 23hr day!
Learn how to cut Africa hair
Typical dopey instructor. Should be at home with his slippers.
watching videos from trainer like this makes me sic & eyes bleeding
to ALL newcomers who watch this : it is not reality and in fact, some of these advices will make u huge mistakes
for example : u never go full inside pallet. u have 99% chance u gotta catch something behind and make it fall.
and it works for eveywhere, from a truck to a pallet rack
i wont speak about the quickness, those ppl never worked in rush time
Whoever would follow this guidance it’ll be they first day on the job and last day on the job too this video needs to be reported 😂🫡
And the guy goes to a claims court and says the company told him to skip safety procedures! kerching!