Thanks for subscribing and commenting ~ If so, you'll need an ESC instead of a PWM controller If you have time, please watch the following video(Arduino). th-cam.com/video/M93DgNz4zeI/w-d-xo.html
Is it possible that I can control the direction of the motor without switch? Could I just simply set the pot to 50% and move it forward or back to switch direction?
Hi i have the same problem as capripiu... but i cannot understand the reply. ....., I mounted those controllers on my hoverboard, I mounted one for each motor, however instead of the potentiometer I mounted an electric bike throttle or trigger, but how do I put it into effect, it already turns, slowly but turns, even at minimum, while with the potentiometer everything is ok, how could I make it work with throttle? Thanks
I understand that the throttle and potentiometer have the same principle. The initial value of the potentiometer is 0. However, the throttle seems to be outputting initially. So, I think it would be a good idea to compare the throttle electric circuit and the potentiometer circuit. I'm afraid there isn't a sufficient answer. thank you
@@meditajin3088 I have the same problem of @keithfrancis4178 and I realized throttle have always a little voltage passing through. How many ohms is your potentiometer?
Hi, I mounted those controllers on my hoverboard, I mounted one for each motor, however instead of the potentiometer I mounted an electric bike throttle or trigger, but how do I put it into effect, it already turns, slowly but turns, even at minimum, while with the potentiometer everything is ok, how could I make it work with throttle? Thanks
Thanks for this helpful video, but when I tried it at home, I attached it with external potentiometer 10K ( also tried 20K), and for sorry the motor motion was making noise at low speed till it became stable at certain speed. then when I go to top speed it stops suddenly. then when I try it again from low speed it works as before. Can you help.
Thank you.. Search for the following specs on Amazon ...DC 6-60V 400W BLDC Three-Phase DC Brushless Motor Controller PWM Hall Motor Control Driver Board 12V 24V 48V
instead of potentiometr can i use rc receiver with out arduino
Thanks for subscribing and commenting ~
If so, you'll need an ESC instead of a PWM controller
If you have time, please watch the following video(Arduino).
th-cam.com/video/M93DgNz4zeI/w-d-xo.html
Is it possible that I can control the direction of the motor without switch? Could I just simply set the pot to 50% and move it forward or back to switch direction?
This controller can only be used with forward and backward direction control switches.
Thank you..
안녕하세요, 이 홀센서 컨트롤러와 인휠모터를 사용해서 자작차를 만드는 학생입니다. 혹시 홀센서 도선 체결에서 문제가 생겨 그런데 선 연결을 어떻게 해야하는지 알려주실 수 있으실까요?
th-cam.com/video/UF8VWYvS_Qw/w-d-xo.htmlsi=r6IMjZEbY9Y5fY0l
이 영상을 보시면 도움이 될겁니다..
오 한국분이셨군요! 혹시 해당 드라이버로 브레이크 기능 써보셨나요??? 이거 회생이라는 말이 있어서 저도 파워서플라이로는 안하고 참고 있는데
브레이크 기능은 사용해보지 않았습니다.
가변저항기로 제어하면 속도를 줄일때 부드럽게 속도가 줄어드네요.
회생은 조금 되겠지만 급 브레이킹 하면 컨트롤러가 문제가 될 수도 있을 것 같네요.
감사합니다..
안녕하세요. 혹시 모터의 홀센서와 아두이노를 연결하여 시계방향회전 반시계회전 정지등을 컨트롤할수 있나요??
선생님 영상중 전동차 무선제어를 보았습니다 그럼 그영상에서도 홀센서를 이방식으로 연결하신건가요?? 홀센서를 아두이노 어디에 연결할지를 모르겠습니다. 도와주십쇼 ㅠㅠ
홀센서는 PWM 컨트롤러에 연결해야됩니다.
시간 나시면 이 영싱을 한번 보세요..
th-cam.com/video/UF8VWYvS_Qw/w-d-xo.html
감사합니다.
컨트롤러 종류에 따라서 가능한데 이 영상의 PWM 컨트롤러는 역방향 스위치를 ON 해야 역방향(반시계방향) 으로 돌아갑니다.
감사합니다..
@@meditajin3088 저는 킥보드용 36v모터 컨트롤러가 있는데요 이걸로는 어떻게 못하나요?
Hi i have the same problem as capripiu... but i cannot understand the reply. ....., I mounted those controllers on my hoverboard, I mounted one for each motor, however instead of the potentiometer I mounted an electric bike throttle or trigger, but how do I put it into effect, it already turns, slowly but turns, even at minimum, while with the potentiometer everything is ok, how could I make it work with throttle? Thanks
I understand that the throttle and potentiometer have the same principle.
The initial value of the potentiometer is 0. However, the throttle seems to be outputting initially. So, I think it would be a good idea to compare the throttle electric circuit and the potentiometer circuit.
I'm afraid there isn't a sufficient answer.
thank you
@@meditajin3088 I have the same problem of @keithfrancis4178 and I realized throttle have always a little voltage passing through. How many ohms is your potentiometer?
Hi, I mounted those controllers on my hoverboard, I mounted one for each motor, however instead of the potentiometer I mounted an electric bike throttle or trigger, but how do I put it into effect, it already turns, slowly but turns, even at minimum, while with the potentiometer everything is ok, how could I make it work with throttle? Thanks
gabyeonjeohang-gi(seuloteul)ui jeohang-gwa jeon-ab-eul cheugjeonghae bosyeossnayo? je saeng-gag-eneun misehan jeonlyuga gong-geubdoego issneungeos gatseubnida. gamsahabnida..
@@meditajin3088 Non si è capito nulla della tua risposta, forse é meglio che scriva in Inglese, il traduttore ha dato frasi irreprensibili
Can this controller work with hall sensor 60 ?
I'm not sure because I haven't used that sensor. sorry..
What type of tire did you use for your hub motor?
These are normal rubber tires.
Thank you..
Thanks for this helpful video, but when I tried it at home, I attached it with external potentiometer 10K ( also tried 20K), and for sorry the motor motion was making noise at low speed till it became stable at certain speed. then when I go to top speed it stops suddenly. then when I try it again from low speed it works as before. Can you help.
Perhaps the wiring of the Hall sensor is incorrect.
Change the A, B, C hall sensor wiring in sequence.
thank you..
Can it be used without the hall sensor
This is difficult with pwm inverters.
A complex controller is required to operate a BLDC motor without a Hall sensor.
Thank you..
@@meditajin3088 but BLDC drills use them without hall sensors
Where did you get the datasheet for the motor controller? Link?
Thank you..
Search for the following specs on Amazon
...DC 6-60V 400W BLDC Three-Phase DC Brushless Motor Controller PWM Hall Motor Control Driver Board 12V 24V 48V
great but my motor has 7 hall wires
2 power lines, U, V, W and the What are the other 2 wires?
@@meditajin3088 no clue